Rigol RP1018H User manual

RIGOL User’s Guide

Publication Number: UGE22X00-1110

RP1018H

RP1018H High Voltage Probe

Sept. 2013

目录 Contents

1. 规格 ..........................................................................................................1

2. 安全须知....................................................................................................1

3. 操作说明....................................................................................................2

4. 匹配电容调整 .............................................................................................2

5. 注意事项....................................................................................................3

6. 清洁 ..........................................................................................................4

7. 电压测试临界曲线 ......................................................................................4

8. 附件 ..........................................................................................................5

1. Specification............................................................................................6

2. Safety Precautions..................................................................................6

3. Operation ................................................................................................7

4. Compensation Adjustment .....................................................................7

5. Warning...................................................................................................8

6. Cleaning ..................................................................................................9

7. Voltage Derating Curve ..........................................................................9

8. Accessories............................................................................................10

-6-

1. Specification

Model RP1018H

Division Ratio 1000:1

Input Resistance 200MΩ

Input Capacitor 1.5 PF

Max. Input: DC+AC peak 18kV CAT II

Max. Input: AC RMS. 12kV CAT II

Max. Loading Current 90uA

Bandwidth DC~150MHz

Rise Time 2.4 ns

Signal / Noise > 60dB at 1kHz ; > 50dB at 1MHz

DCV Accuracy ≤3% Full Range

ACV Accuracy ≤3% at 1 kHz

Temp. Coefficient ≤200 PPM / ℃

Compensation Range 10PF ~ 35PF

Safety Meets EN61010-031 CAT II

Cable Length 2M ± 0.2M

Operation Temperature Range -10 ~ 55℃

Humidity 85% RH or less (at 35℃)

Storage Temperature Range -20 ~ 70℃

Color: Handel/Body Black / Yellow

Weight / Volume 460g /80(W) x 80(H) X 320(L) mm

2. Safety Precautions

Thank you for purchasing RP1018H high voltage probe. High voltage probe can

prevent high voltage testers from subjecting to unexpected shocks when doing high

voltage measurement work. Before using the high voltage probe, the operator must

read and fully understand the safety rules.

In addition, this high voltage probe only for the person who are trained, experienced,

or otherwise qualified to recognize hazardous situations and who trained in the safety

precautions that necessary to avoid possible injury when using such a device.

-7-

Do not work alone when working with high voltage circuits.

For your own safety, inspect the probes for cracks and frayed or broken leads before

each use. If defects are noted, DO NOT USE the probe.

Hands, shoes, floor and work bench must be dry. Avoid making measurements under

humid, damp or other environmental conditions that might affect the safety of the

measurement situation. If possible, always turn the high voltage source off before

connection or disconnection the probe.

The probe body should be kept clean and free of any conductive contamination. The

probe is for indoor use only.

3. Operation

1) Connect the divider probe common lead (alligator clip) to a good earth ground or

reliable ground.

2) Connect the BNC connector to the BNC input of your oscilloscope.

3) Select the desired range of your oscilloscope.

NOTE

Please turn the high voltage source off before making any connections.

4. Compensation Adjustment

Connect the probe to the oscilloscope, and input a 200Hz square wave to the probe tip.

After that adjust the oscilloscope controls to display a few cycles of the waveform.

Adjust the trimmer located in the BNC plug for a flat topped square wave.

Illustration of 200Hz square wave adjustment

-8-

CAUTION

1) Please use function signal generator to output 20 Vp-p, 200 Hz square waveform.

2) Non-professionals do not adjust the Hole 2 and Hole 3.

3) This product is already adjusting Hole 2 and Hole 3. Please feel free to operation.

4) Use the adjust bar attached only.

5) When the measuring frequency was 40MHz up, you must replace the long earth

lead with the Alligator Clip (BP-276N-D) to obtain a best earth and the best

frequency response.

5. Warning

1) Do not attempt to take the ground of test equipment away from the ground

terminal.

The ground connection is critical to the safety operation of the probe. Failure to

make this connection may result in personal injury or damage to the probe or

oscilloscope. You must be sure to connect the ground before the probe tip comes

into contacting with the high voltage. And the ground connection must not be

removed until the probe tip has been taken away from the high voltage source.

2) Do not connect the ground clip to the high voltage source or the probe tip to the

ground for any reason.

3) Before turning the high voltage on, make sure that no part of your body is in

contact with the device.

4) Remembering that the voltage being measured is 1000 times greater than the

Adjust the frequency

response of the probe to

match your oscilloscope by

the adjust bar attached only.

For 40MHz up

Measuring Frequency

Hole 2.

for 200kHz Square

Wave Adjustment Hole 3.

for Bandwidth

Adjustment

Hole 1.

for 200Hz Square Wave Adjustment

-9-

voltmeter reading.

5) Disconnect the probe tip from the high voltage source before removing the

ground clip.

6. Cleaning

Clean only the exterior probe body and cables. Use a soft cotton cloth lightly moistened

with alcohol and water. Do not allow any portion of the probe to submerge in the liquid.

Dry the probe thoroughly before measuring voltage.

Do not place the probe into the corrosive solvents or fumes as these will cause

deterioration to the probe and cables.

7. Voltage Derating Curve

RP1018H (18kV:3MHz / 300V:150MHz / 100V:1GHz)

Voltage (dc+ac peak)

Frequency

-10-

8. Accessories

Test CRT for H.V. Adjust bar

Carrying Box

If you have any problem or requirement when using our products or this manual,

please contact RIGOL.

E-mail: servic[email protected]

Websites: www.rigol.com

Table of contents

Other Rigol Test Equipment manuals

Rigol

Rigol DS1000CA series Operating instructions

Rigol

Rigol DS1000Z Series Quick start guide

Rigol

Rigol DS1000CA series User manual

Rigol

Rigol MSO8000 Series User manual

Rigol

Rigol DG800 Pro Series Operating instructions

Rigol

Rigol RP7000 Series User manual

Rigol

Rigol RP1003C User manual

Rigol

Rigol MSO1000Z series User manual

Rigol

Rigol DS6000 Series User manual

Rigol

Rigol DHO800 Series User manual

Rigol

Rigol DHO1202 User manual

Rigol

Rigol DS8000-R Series User manual

Rigol

Rigol RP1010H User manual

Rigol

Rigol DS1204B Operating instructions

Rigol

Rigol DHO924 User manual

Rigol

Rigol DS6000 Series User manual

Rigol

Rigol MSO4000 Series User manual

Rigol

Rigol DS1000CA series User manual

Rigol

Rigol DS1000B Series User manual

Rigol

Rigol DS4000E Series Operating instructions

Rigol

Rigol DS1000E series Installation and operation manual

Rigol

Rigol DG900 Pro Series User manual

Rigol

Rigol MSO1000Z series Operating instructions

Rigol

Rigol DHO900 User manual

Popular Test Equipment manuals by other brands

SMART

SMART KANAAD SBT XTREME 3G Series user manual

Agilent Technologies

Agilent Technologies BERT Serial Getting started

Agilent Technologies

Agilent Technologies N3280A user guide

Vernier

Vernier Go Direct Voltage manual

Lifeloc

Lifeloc R.A.D.A.R. quick start guide

Fluke

Fluke T5-600 Service information

Mercury

Mercury TSL01 user manual

MAHA

MAHA MBT Series Original operating instructions

Fuji Electric

Fuji Electric P-61 instruction manual

ETC

ETC SealerAtor user manual

Skyfine

Skyfine ETHYWAY V2 user manual

Appion

Appion G5 Twin Operation manual

PCB Piezotronics

PCB Piezotronics 8159-0112A Installation and operating manual

BW Technologies

BW Technologies MicroDock II user manual

Sun Nuclear

Sun Nuclear 1027 user guide

Biomark

Biomark HPR LITE READER user manual

Hioki

Hioki 3169-20 instruction manual

Ashcroft

Ashcroft ATE-100 operating manual