Riello 3473784 Quick start guide
2915897 (2) - 08/2012
Installation, use and maintenance instructions
Pressure jet burner
CODE MODEL TYPE
3473784 PRESS GW 605 T80
5897
1
1- Suction line fitting
2- Return line fitting
3- Suction gauge fixing point (G 1/8)
4- Pressure gauge fixing point (G 1/8)
5- Pump pressure adjuster
6- Wiring terminal board
7- Combustion head control shaft
8- Fair leads
9- Control box reset button with signal of lock-out
DIMENSIONS (mm)
* Length available with special blast tube to be separately required.
Thermal power 107 / 178 - 350 kW - 92.000 / 153.000 - 301.000 kcal/h
Output 9/15 - 30 kg/h
Fuel Gas oil, max. viscosity at 20 °C: 6 mm2/s (1.5 °E)
Electrical supply Single-phase 220V +10% -10% ~ 60Hz
Motor 1.85 A / 220V
Capacitor 8 µF
Ignition transformer Primary: 1.8 A / 220V - Secondary: 1x 8 kV - 30 mA
Absorbed electrical power 0.4 kW
Fig. 1
Burner
Boiler front plate
drilling
Quantity Accessories
2 Flexibles oil-lines
2 Connectors for flexibles
2 Gasket for flexibles
1 Flange gasket
4Screws
1 Pipe fitting
1 Pipe fitting gasket
5897
2
PRESSURE IN THE COMBUSTION CHAMBER - OUTPUT
(in compliance with DIN 4787)
The burner is drawn for on-off operation and high-low operation.
Minimum firing-rate at on-off operation is 15 kg/h (two nozzles) and 9 kg/h (one nozzle) with high-low operation.
DIMENSIONS OF THE TEST COMBUSTION-CHAMBER (DIN 4787)
Pressure in the combustion
chamber in mbar
Burner output kg/h
Specific thermal test load
D = Boiler diameter in mm
P = Position of the mobile
back in mm
5897
3
HYDRAULIC SYSTEM
Gravity feed from the bottom of the oil storage tank
Gravity feed over the top of the oil storage tank
H= Difference in height; L= The total length of the suction line, including the vertical section.
The copper pipes of 8 mm and 10 mm I.D., as shown on the tables above, may be replaced by steel pipes of 1/4”
or 3/8” Gas.
The dimension P should not exceed 10 m, to avoid
breakage of pump seals.
H
meters
L meters
I.D. 8 mm I.D. 10 mm
0.5 5 10
11020
1.5 15 30
22040
The dimension P should not exceed 10 m, to avoid
breakage of pump seals.
Oil lines must be perfectly sealed. The use of copper
pipe is therefore recommended. The pump suction
must not exceed 4 m w.c. (30 cm Hg) because beyond
this value the pump becomes noisy.
The return line must terminate at the same level as the
foot valve; otherwise the pump may become air-locked.
H
meters
L meters
I.D. 8 mm I.D. 10 mm
03270
0.5 28 62
12455
1.5 20 48
21640
3725
3.5 - 10
Suction feed
5897
4
BURNER ELECTRICAL WIRING
(carried out by the factory)
KEY TO LAYOUT
CCapacitor TA Ignition transformer
FR Photocell TB Burner ground (earth) connection
MB Wiring terminal block V1 1st stage solenoid valve
MV Fan motor V2 2nd stage solenoid valve
RMO Control box
2463
5897
5
ELECTRICAL CONNECTIONS TO THE WIRING TERMINAL BLOCK
(to be carried out by the installer)
NOTICE
- The electric wiring carried out by the installer must be in compliance with the rules in force in the Country.
- Leads minimal section 1 mm2.
FLAME MODULATION
The flame modulation is obtainable through the thermostat, controlling the second valve, connected to the terminals
8 and 9, removing the existing bridge.
2646
KEY TO LAYOUT
HRemote lock - out signal TL Limit control device system
MB Wiring terminal block TR High - low mode control device system
PS Lock - out reset button TS Safety control device system
TB Burner ground (earth) connection
5897
6
FIXING OF THE ELECTRICAL WIRES
All the electrical wires, which are to be connected to the terminal block 6) (fig. 1) shall pass through the fair leads 8)
(fig. 1) as per this scheme.
1- Single phase supply: fair lead Pg 13.5
2- Adjustment thermostat: fair lead Pg 13.5
3- Safety thermostat: fair lead Pg 13.5
4- 2nd stage thermostat: fair lead Pg 13.5
5- 6- 7- Pre-sheared holes
Further prospective signals or controls can be connected to the burner wiring terminal board by removing the metal
weldnuts from the pre-sheared holes and inserting a commun fair lead for the passage and the clamping of the leads.
NOTES
- Do not exchange the neutral wire with the phase (avoid the plug-pin connection).
- Carry out a safe earth connection.
- Verify the burner stop by opening the boiler thermostat and the burner lock-out by darkening the photo-resistance.
ACCESSORIES
• RADIO DISTURBANCE PROTECTION KIT
If the burner is installed in places particularly subject to radio disturbance (emission of signals exceeding 10 V/m) owing
to the presence of an INVERTER, or in applications where the length of the thermostat connections exceeds 20 metres,
a protection kit is available as an interface between the control box and the burner.
Code 3010386
5897
7
BURNER ADJUSTMENT
Establish, on the basis of the output desired, and in accordance with the table and the diagram underneath:
- the type of nozzle;
- the pump pressure;
- the combustion head setting.
EXAMPLE
The burner has to be matched with a boiler of 210 kW.
Assuming an efficiency of 90%, we need to develop approximately 233 kW i.e. burning reughly 20 kg/h.
In the output column we find, corresponding to 20, on the left, the required nozzles (2 of 2.50 GPH at 60°) the pump
pressure (12 bar), and on the right the correct position of the combustion head (3 set-points).
(1) Nozzles of the major existing makers may be used.
It might well be possible however, that for certain specific outputs, one type of nozzle is less suitable than others.
It is recommended not to change the atomizing angle.
(2) It is recommended not to goes down to the 10 bar, otherwise the jack controlling the air damper will open with
difficulty.
The pump pressure may be varied by acting on the screw 5) (fig. 1) and it can be controlled by placing a pressure
switch on the pressure gauge 4) (fig. 1).
Output in kg/h
(4) Adjustment of the head (N° of set - points)
5897
8
(3) The indicated outputs are drawn from the average statistical data of
our tests.
Real output may well vary by ± 5%.
(4) The rear level of the control-shaft (7) (fig. 1) must line-up with the
set-point number, indicated by the diagram.
In the sketch on the right, the shaft is shown, in the position required
by the example on page 7.
AIR DAMPER ADJUSTMENT
Air damper adjustment for the first flame
Loosen the screw (1), the nut (3) and move the graduated scale (2) so that the pointer (4) lines-up with the set-point
desired; then tighten the screw (1) and the nut (3). A sufficiently exact control, valid for 12 bar and for the different
boilers pressurizations is given by the following table:
NOTE
For any necessary combustion adjustment, at the first flame stage, remove the bridge or the second stage thermo-
stat (see page 5).
Regulation of the air damper for the second flame
Loosen the threaded locking-ring (1) and tighten the hexagon (2) in order to reduce flow; slacken the hexagon to
increase flow.
This adjustment shall be modified, from time to time, in relation to the various combustion chambers pressurizations.
Set - point 3
On the sketch the graduated scale is shown, in
the position required by the example on page 7.
4
Set - point 2
This manual suits for next models
1
Table of contents
Other Riello Burner manuals
Riello
Riello Gulliver RG5DF Quick start guide
Riello
Riello 20066726 Quick start guide
Riello
Riello RG2D Quick start guide
Riello
Riello GAS 7 P/M Quick start guide
Riello
Riello Riello F10 User manual
Riello
Riello DB 3 SE FGR Quick start guide
Riello
Riello RLS 70 Quick start guide
Riello
Riello 40 G5R Quick start guide
Riello
Riello 40 FS20D Quick start guide
Riello
Riello Gulliver RG2KD Quick start guide
Riello
Riello PRESS 4G Quick start guide
Riello
Riello RLS 70 Quick start guide
Riello
Riello N10 Quick start guide
Riello
Riello RDB2.2 BX 15-20 Quick start guide
Riello
Riello 40 FS8 TL Quick start guide
Riello
Riello 40 GS5 Quick start guide
Riello
Riello Gulliver RG4D Quick start guide
Riello
Riello RS 160/M BLU Quick start guide
Riello
Riello RS Series Quick start guide
Riello
Riello DR 32 SE FGR Quick start guide
Popular Burner manuals by other brands
PROPOINT
PROPOINT 8933657 manual
baltur
baltur TBL 1000 ME Instruction manual for installation, use and maintenance
Riello Burners
Riello Burners P 200 P/G Installation, use and maintenance instructions
WLD-TEC
WLD-TEC powerjet instruction manual
MSR
MSR DRAGONFLY instruction manual
baltur
baltur COMIST 23SP Instruction