Richmat HJC56 Ble User manual
1. Remark:
Up to 4 motors
BLE control available
Memory function
Color: black
2. Dimension:(mm)
3.System configuration diagram
Before powering on, please install the accessories in place according to
the system configuration diagram
4.Remote control button silicone diagram
5.Fixed position size
ZG
LOUNGE
TV
SNORE
Head（mm）
49
127
149
30
Foot（mm）
125
83
94
0
6.Remote control function description
Button
label
Function
1
Press the button, the motor will run to the TV position
with one button (there is an initial position)
Multiplexing function: Press and hold the FLAT button
while pressing the TV button, the buzzer sounds, the
backlight flashes, and the current motor status is
recorded to the TV position. (Power-off memory clear)
2
Press the button, the motor will run to the LOUNGE
position with one button (there is an initial position)
Alternate function: Press and hold the FLAT button while
pressing the LOUNGE button, the buzzer sounds, the
backlight flashes, and the current motor status is
recorded to the LOUNGE position. (Power-off memory clear)
3
Press the button, the motor will run to the ZG position
with one button (there is an initial position) Alternate
function: Press and hold the FLAT button while pressing
the ZG button, the buzzer sounds, the backlight flashes,
and the current motor status is recorded to the ZG
position. (Power-off memory clear)
4
Press the button to extend the back motor, and the back
motor extends to the position of maximum stroke to stop.
Release the button in the middle to stop the motor.
5
Press the button to retract the back motor, and the back
motor retracts to the 0mm position to stop. Release the
button in the middle, and the motor stops.
6
The Partner Control key has three options: ①Press the
Partner Control key, the -10min light on the left side
of the decorative strip will light up, and you can control
bed A at this time; ②Press the Partner Control button
again, the -20min light on the right side of the
decorative strip will light up, and the B bed can be
controlled; ③Press the Partner Control button again,
the left side + right side of the decorative strip
-10min+20min lights at the same time, you can control the
AB bed at the same time.
7
Press the button, the motor will run to the SNORE position
with one button (there is an initial position) Alternate
function: Press and hold the FLAT button while pressing
the SNORE button, the buzzer sounds, the backlight
flashes, and the current motor status is recorded to the
SNORE position. (Power-off memory clear)
8
Press the button to extend the leg motor, and the leg motor
extends to the maximum stroke position to stop. Release
the button in the middle to stop the motor.
9
Press the button to retract the leg motor, and the leg
motor retracts to the 0mm position to stop. Release the
button in the middle, and the motor stops.
10
Press the button, the motor will run to memory position
1 with one button (no initial value) Alternate function:
Press and hold the FLAT button while pressing the M1
button, the buzzer sounds, the backlight flashes, and the
current motor status is recorded to the memory position
1. (Not cleared after power failure)
11
Press the button, the motor will run to memory position
2 with one button (no initial value) Alternate function:
Press and hold the FLAT button while pressing the M2
button, the buzzer sounds, the backlight flashes, and the
current motor status is recorded to the memory position
2. (Not cleared after power failure)
12
One key to restore the motor reset position, the control
box will automatically perform a reset operation after
power on.
13
Multiplexing function: press the button, if the head
massage motor is not activated, it will start the head
massage motor and enter the "CONSTANT" mode, if the head
massage motor is activated, the vibration intensity of
the head massage motor will be enhanced, a total of 3
intensities, When the intensity increases to the maximum,
press the button to turn off the massager. (Default 30min
is off)
14
Bed bottom lamp on/off (default 5min off)
15
Multiplexing function: Press the button, if the foot
massage motor is not activated, the foot massage motor
will be activated and enter the "CONSTANT" mode. If the
foot massage motor has been activated, the vibration
intensity of the foot massage motor will be increased,
with a total of 3 intensities. When the intensity
increases to the maximum, press the button to turn off
the massager. (Default 30min is off)
16
Reuse function button: Before pressing the button, if the
massager is in working state, after pressing the button,
all massagers will be turned off, and the working time
of the next massage motor will be set to 10min, 20min and
30min respectively. The timing time is displayed by two
indicator lights, and the maximum timing time is 30min.
If the massager is not in working state, it will directly
time the next massage motor working time.
17
Press the button to turn on the flashlight, release the
button to turn off the flashlight.
18
Adjust the massage motor mode. After the massager has been
turned on, press this button, the working massage motor
enters the "PULSE" mode, press the button again, the
massage motor enters the "WAVE" mode, press the button
again, the massage motor enters In "CONSTANT" mode, after
pressing the button again, the massage motor enters the
"PULSE" mode and cycles in sequence.
Coding method: 1. First press the light on the left side of the Partner
Control decorative strip for -10 minutes to light up, then press
[remote control head up + foot up (4, 8) + control box code key] the
buzzer will sound, indicating that it is paired with control box A
The code is successful; press the light on the right side of the Partner
Control decorative strip again for -20 minutes, and then press the
[remote control head up + foot up (4, 8) + control box code key] buzzer
sounds, indicating that it is with control box B The code pairing is
successful. 2. The remote control is powered off, and the default mode
is A+B. 3. The control box has a reset function for the code key.
Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
Table of contents
Other Richmat Control Unit manuals
Popular Control Unit manuals by other brands
Festo
Festo Compact Performance CP-FB6-E Brief description
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Quick installation guide
JS Automation
JS Automation MPC3034A user manual
JAUDT
JAUDT SW GII 6406 Series Translation of the original operating instructions
Spektrum
Spektrum Air Module System manual
BOC Edwards
BOC Edwards Q Series instruction manual
KHADAS
KHADAS BT Magic quick start
Etherma
Etherma eNEXHO-IL Assembly and operating instructions
PMFoundations
PMFoundations Attenuverter Assembly guide
GEA
GEA VARIVENT Operating instruction
Walther Systemtechnik
Walther Systemtechnik VMS-05 Assembly instructions
Altronix
Altronix LINQ8PD Installation and programming manual
