RF SOLUTIONS MAINSLINK–PRO User manual

MAINSLINK–PRO

DS-MAINSLINKPRO-2

•

MAINSLINK-PRO

DS-MAINSLINKPRO-2

PATENT PENDING

Application example: WORCESTER-BOSCH Boiler Installation

Warnings :

• Product is not independently isolated, ISOLATE the mains electricity supply before

removing the cover and observe any relevant safety precautions. Maintenance to the

product that involves removal of the cover should only be carried out by a competent

person or qualified electrician.

• F2 Fuse rating is 4A (T) 250 H (Ceramic). Replace fuse with same type and rating.

• Relay is rated at 10A peak, and 5A constant.

• Product must be connected to a switch fused (spur/supply) or BS 1363 Plug. It is

recommended a single Fuse Spur is used to supply the Boiler and MAINSLINK-PRO

jointly so that they are isolated together

CH ON

DHW

This system provides two functions, Switching of the Pump from the boiler and Switching of the

Boiler from the wiring Centre.

Connections at the Boiler

The boiler output to the Pump is connected to the MAINSLINK-PRO A, (Lin)

The boiler switching input is connected to the MAINSLINK-PRO A (Lout)

It is recommended to use a single switch fuse spur to supply the Boiler and Mainslink together. (so

that both appliances are isolated together)

Connections at the Wiring Centre

The thermostats switching output to switch the boiler is connected to the MAINSLINK-PRO B (Lin)

The Pump is connected to the MAINSLINK-PRO B (Lout)

Operation

When the wiring centre commands the Boiler ON MAINSLINK-PRO B (Lin) is switched is Live then

MAINSLINK-PRO A Lout will automatically switch a LIVE signal to turn the boiler on.

When the Boiler switches the Pump drive ON MAINSLINK-PRO, (Lin) “A” is switched Live then

MAINSLINK-PRO

DS-MAINSLINKPRO-2

PATENT PENDING

SWITCHED LIVE

N N L

Permanent

LIVE FEED

Lin (LIVE IN)

PERMANANT

SUPPLY

Lout (LIVE OUT)

Lin

Comm

Lout

WDOG

MODE

MOM/LAT

MAG Switch

Installation

Connect the Supply to both units

Connect the permanent LIVE and NEUTRAL supply.

Comms LED

Check the Green LED is always ON when both units are powered

Connect the Switched Input L in

When the Switched Live input (LIN) is ’LIVE’ the Red Lin will illu-

minate, and the L out at the other unit will then switch Live out

Connecting the Switching Load L out

Connect the LOAD Live to Lout

When the Switched Live Output (LOUT) is ’LIVE’ the Red L OUT

LED will illuminate

LED Off On Flashing

L in No Input LIVE input at

terminal

Comms RF Link Healthy See Comms

LED Table

L out Output is

OFF Output is LIVE

Watchdog Signal

MAISNLINK-PRO automatically transmits an rf ‘watchdog’ signal every ~30secs in the back-

ground. If the WDOG signal is not received within 90seconds, the output will drop out and

comms LED will flash.

This provides improved reliability and security useful in noisy or poor reception areas.

Multiple System Operation:

Each MAINSLINK-PRO system contains a unique identity so multiple systems can operate within

the same area without interfering with each other.

Comms LED

The Comms indicates the status of the MAINSLINK-PRO

COMMS LED Table

ON One Flash Two Flashes 3 Flashes

Operation

Status RF Link

Healthy Out of range Powered

But unpaired In Pairing Mode

Descrip-

tion

System

operating OK

No RF connection

to other

MAINSLINK-PRO

Waiting to be paired

to another

MAINSLINK-PRO

Actively sending an

RF ‘Please Pair

message’

MAINSLINK-PRO

Disclaimer:

Whilst the information in this document is believed to be correct at the time of issue, RF Solutions Ltd does not accept any liability whatsoever for its accuracy, adequacy or completeness. No

express or implied warranty or representation is given relating to the information contained in this document. RF Solutions Ltd reserves the right to make changes and improvements to the

product(s) described herein without notice. Buyers and other users should determine for themselves the suitability of any such information or products for their own particular requirements or

specification(s). RF Solutions Ltd shall not be liable for any loss or damage caused as a result of user’s own determination of how to deploy or use R F Solutions Ltd’s products. Use of RF

Solutions Ltd products or components in life support and/or safety applications is not authorised except with express written approval. No licences are created, implicitly or otherwise, under any

of RF Solutions Ltd’s intellectual property rights. Liability for loss or damage resulting or caused by reliance on the information contained herein or from the use of the product (including

liability resulting from

negligence or where RF Solutions Ltd was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict QuasarUK Ltd’s liability for death or

personal injury resulting from its negligence.

Important European compliance information

This RF Solutions product meets the essential requirements of the European Radio Equipment Di-

rective 2014/53/EU and has been tested to European Harmonised Standards and CE marked accord-

ingly. A copy of the EU Declaration of Conformity can be located on the RF Solutions Website,

www.rfsolutions.co.uk/certification-i59.

36.00

88.00

88.00~25.00

30.00

Dims in mm

Fixing Instructions:

1.Fix the rear of the MAINSLINK-PRO enclosure to the wall using the template above.

2.Ensure that all fixing screws are screwed flush to the enclosure.

3.Ensure that the screw covers are put in place. These ensure water proofing and insulate the

PCB from the wall fixing screws. Screw Covers are found inside the rear of the enclosure.

4.Once the enclosure is fixed to the wall, screw on the front plate with the PCB in place.

Dimensions and Wall mounting information:

MAINSLINK-PRO is a professional use product and should only be installed by a competent

person. The product must be FIXED to the wall (EN60950 4.1)

RF Solutions Ltd. Recycling Notice

Meets the following EC Directives:

DO NOT

Discard with normal waste, please recycle.

ROHS Directive 2002/95/EC

Specifies certain limits for hazardous substances.

WEEE Directive 2002/96/EC

Waste electrical & electronic equipment. This product must be disposed of through a licensed WEEE collection point. RF

Solutions Ltd., fulfils its WEEE obligations by membership of an approved compliance scheme.

MAINSLINK-PRO

DS-MAINSLINKPRO-2

PATENT PENDING

1. Apply a 230Vac supply to the first MAISNLINK-PRO

2. Briefly place a magnet across enclosure (top left corner

as shown) to activate the internal reed switch.

3. The GREEN comms LED will flash 3 times to show in Pair-

ing Mode

Advanced Operation—Pairing together two MAINSLINK-PROs

NOTE: This system does not require pairing , they are supplied ready to operate!

This process is described for advanced use only.

Erasing a MAINSLINK-PRO

3. Apply 230Vac to the second MAINSLINK-PRO

4. Briefly place a magnet across enclosure (top left corner as

shown) to activate the internal reed switch.

5. The GREEN comms LED will flash 3 times to show in Pairing

Mode

6. The two MAINSLINK-PRO units which will now auto pair to-

gether (allow 30 secs -Green Comms LED will stay on.)

To erase the system hold a magnet beside the top left

corner of the enclosure for 10 seconds as shown.

Repeat this process on both units to erase system.

Technical Specification:

Dimensions: 88 x 88 x 54mm

Electrical Characteristics Min Typical Max Units

Supply Voltage TX/RX: 100 230 250 Vac

Operating Frequency* 869.50 MHz

RF Output power +20 dBm

Bandwidth (Spreading Factor) 60 KHz

Maximum switching load (RX) 1000 W

Time delay from Tx Transmit to Rx Relay

operation:

Mode 3

Mode 7

Secs

MAINSLINK-PRO

DS-MAINSLINKPRO-2

PATENT PENDING

Jumper Link Setting

There are three Jumper Links which may be used to configure the following

Link Open Fitted

WDOG Watchdog Active

MODE LORA Mode 3 LORA Mode 7

MOM/LAT Momentary Latching

N N L

Permanent

LIVE FEED

Lin (LIVE IN)

Lout (LIVE OUT)

Lin

Comm

Lout

WDOG

MODE

MOM/LAT

WDOG - WATCHDOG

When the WDOG link is fitted each MAINSLINKPRO automatically sends a background watch-

dog RF signal and expects to receive a corresponding WDOG signal from its partner.

If the WDOG signal is not received within 90seconds, the output will drop out and comms LED

will flash.

This provides improved reliability and security useful in noisy or poor reception areas.

MODE

LORA Mode 3, Faster operation shorter range (Line of sight upto 3Km / 500m in buildings)

This mode is recommended for general operation,

LORA Mode 7, Slower operation Long range (Line of sight upto 5Km / 1Km in buildings)

This mode can be used where additional RF penetration / range is required

Note! In this mode a transmitted signal can take 2 seconds to trigger the receiver.

MOM/LAT - Momentary or Latching

Sets the Relay changeover contacts to operate as Momentary or Latching.

MOMENATRY: used for MAINSLINK TO MAINSLINK

LATCHING: is used when MAINSLKINK is being controlled from an RF Solutions hand held Re-

mote transmitter.

Switching Lower Power LED Lights

Mainslink incorporates a “snubber” protection circuit which

is recommended when motor switching. This is incorpo-

rated when Jumper Link J2 is connected between pins 1 & 2

(horizontally across the top pins)

If using MAINSLINK to switch lower power LED lighting the

snubber circuit can cause the LED lights to faintly glow.

To remove this the snubber circuit can be removed by taking

out the Snubber Jumper link as the image shows

Table of contents

Other RF SOLUTIONS Remote Control manuals

RF SOLUTIONS

RF SOLUTIONS TAURUSDIN User manual

RF SOLUTIONS

RF SOLUTIONS EZTEXT User manual

RF SOLUTIONS

RF SOLUTIONS ELITE-L Series User manual

RF SOLUTIONS

RF SOLUTIONS QS-TRAP-SHUFFLE-R1 User manual

RF SOLUTIONS

RF SOLUTIONS EZTEXT-DIN User manual

RF SOLUTIONS

RF SOLUTIONS FOBBER-8T6 User manual

RF SOLUTIONS

RF SOLUTIONS EZTEXT User manual

RF SOLUTIONS

RF SOLUTIONS ELITE Series User manual

RF SOLUTIONS

RF SOLUTIONS ELITE-KIT User manual

RF SOLUTIONS

RF SOLUTIONS Hornet-S1 User manual

RF SOLUTIONS

RF SOLUTIONS HORNETPRO Series User manual

RF SOLUTIONS

RF SOLUTIONS RIoT-Minihub User manual

RF SOLUTIONS

RF SOLUTIONS ELITE User manual

RF SOLUTIONS

RF SOLUTIONS HORNETPRO-8S1 User manual

RF SOLUTIONS

RF SOLUTIONS Keeloq FOBLOQA-4T1 User manual

RF SOLUTIONS

RF SOLUTIONS HORNETPRO MAINS User manual

RF SOLUTIONS

RF SOLUTIONS EZTEXT User manual

RF SOLUTIONS

RF SOLUTIONS ELITE Series User manual

RF SOLUTIONS

RF SOLUTIONS QUANTAFOB User manual

RF SOLUTIONS

RF SOLUTIONS TRAP User manual

RF SOLUTIONS

RF SOLUTIONS MAINSLINK User manual

RF SOLUTIONS

RF SOLUTIONS ELITE User manual

RF SOLUTIONS

RF SOLUTIONS PRO Series User manual

RF SOLUTIONS

RF SOLUTIONS PRO Series User manual

Popular Remote Control manuals by other brands

Panasonic

Panasonic EUR7622KB0 Operation guide

Bang & Olufsen

Bang & Olufsen Beo4 user manual

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 user manual

Multiplex

Multiplex PROFI TX 9 instructions

One Remote

One Remote RMB4 user manual

FUTABA

FUTABA 9ZAP - PART2 manual

HR Matic

HR Matic HR MULTI 3 quick start guide

Yamaha

Yamaha ACC-GNRST-30-20 installation instructions

EisSound

EisSound KBSOUND user manual

Marantz

Marantz RC101 user guide

Conrad

Conrad FS20 TC6 operating instructions

Anritsu

Anritsu MP1777A Operation manual

Niles

Niles WVC100 Installation & operating guide

RCA

RCA RCU1300 manual

Bang & Olufsen

Bang & Olufsen BEO6 Getting started

GE 94901 instruction manual

Onbon

Onbon YQ1-75 user manual

FUTABA

FUTABA R7108SB Full manual