Resideo ADEMCO 4208SN Assembly instructions

ADEMCO 4208SN

V-Plex Eight Zone Expander

Installation and Setup Guide

FEATURES

The ADEMCO 4208SN is a V-Plex

eight zone expander for use with

Resideo controls that support serial number V-Plex (polling loop)

devices. Characteristics of this device include:

•Can be optionally powered from the control panel aux. power

supply to reduce the amount of current draw from the polling loop.

•Uniquely identifies 8 EOLR supervised zones (all zones use 10k

resistors, supplied).

•Each zone is identified by a unique serial number, which is

assigned via on-board DIP Switches.

•Detects faults on all zones within 400ms of occurrence. Loops A

& B can be programmed for fast (10ms) response.

•Provides cover tamper protection, which may be enabled or

disabled via on-board DIP Switches.

MOUNTING

1. Power should be disconnected before

proceeding.

2. Be sure to mount the 4208SN before making any

wire connections.

When mounted remotely, tamper protection is required. Holes on the

back of the module’s housing permit it to be mounted horizontally or

vertically. Wires can exit from the side or the breakout on the back of

the housing. To enable tamper protection, set DIP Switch 8 to OFF

and attach the tamper magnet (provided) (Figure 1) to the module

inside cover. Be sure to enable the expansion zone tamper option at

the control (program field *24 = 0). If the module’s cover is removed,

the magnet attached to the cover (positioned near the reed switch) will

cause a tamper signal to be sent to the control for every active zone on

the 4208SN module. When the installation is complete, install the

cover and affix the Serial Number and Zone Assignment Tables to the

inside cover of the control.

When mounted inside the cabinet with the control, the 4208SN should

be mounted horizontally and does not need tamper protection,

provided the cabinet is supervised. Insert two screws into the raised

metal tabs leaving the heads app. 1/8” exposed, then hang the

4208SN using the two slots on the back.

1. INSERT BOTTOM TABS FIRST.

2. ENGAGE TOP WITH CLIP. 4219-002-V0

Figure 1. Tamper Magnet Installation

WIRING

For CE installations, ADEMCO N6361 EMI

suppression bead is required. Refer to the N6361

installation guide for wire routing instructions.

Polling loop and protection loop wires can be brought in either through

the back or front of the unit by removing the knockouts. Use 22 gauge

twisted pair wire for polling loop connections. All protection loops use

10k EOL resistors (included). A maximum resistance of 300 ohms is

allowed on protection loops (excluding EOLR). See Figure 2 for all

connections. Keep in mind that connections to the polling loop are

always required, while aux. power connections are optional.

For UL commercial and household fire installations,

no more than one wire per terminal may be

connected.

4208SN-SOC-V1

NOTES:

4208SN

NOT

USED

( ) GR OUND

(+) 12V

( )

(+)

1

2

3

5

4

4 65

TB2

TB1

REED (TAMPER) SWITCH

10k 10k

LOOPS: A B C D E F G H

(EACH LOOP'S MAX

RESISTANCE:

300 ohms + 10k EOLR)

ON

DIP Switches

1 3

2 10 12

11

7 9

8

10k 10k 10k 10k10k 10k

8

12345 6 7

TO POLLING LOOP

(USE  TWISTED P AIR)

IF USING AUXILIARY POWER ON COMMECRICAL

FIRE/BURG COMBINATION SYSTEMS

(e.g.VISTA-128FBP), DO NOT CONNECT THE

POLLING LOOP GROUND ON TERMINAL 2.

AUXILIARY POWER CAN ONLY BE USED IN

BURGLARY APPLICATIONS.



FOR CE INSTALLATIONS A N6363 EMI

SUPPRESSION BEAD IS REQUIRED.

OPTIONAL AUX.

POWER INPUT.

SEE NOTE 1.

1.



Figure 2. Wiring Diagram

1. For dry, indoor use only.

2. Do not install in air-handling spaces.

3. All circuits are supervised and power-limited.

4. Use only 14-22 AWG wire.

5. Refer to the control panel installation

instructions for specific programming /

installation requirements.

For all fire (NFPA) and UL Commercial Burglary

installations, the 4208SN must be tamper protected

or mounted in a tamper-protected cabinet.

This device is NFPA

72 Compliant.

DIP SWITCH SETTINGS

The DIP Switches are used to assign serial numbers to loops A

through H. You can assign the serial number of any module loop to

any of the control panel’s expansion zones. You do not lose zone

numbers if you do not use all eight module loops. To select serial

numbers for loops A through H, follow the steps below using Figure 3

and Tables 1 through 4 for DIP Switch settings:

Select fast/slow response for loops A and B using DIP Switch 1:

Fast = OFF (10msec) Slow = ON (400msec). Do not select fast

response for a zone dedicated for Fire usage.

Select Serial Number Assignment Table containing the desired

group of 8 serial numbers (Tables 1 through 4) using DIP switches

6 and 7.

Select the group of 8 serial numbers using DIP switches 2, 3, 4,

and 5. See the Table selected in step 2 for serial number

assignments. If using more than one 4208SN be sure to set each

one to a different group setting.

Select the Tamper Protection setting using DIP Switch 8: Tamper

Disabled = ON Tamper Enabled = OFF. Tamper will report for

every active zone on the 4208SN module.

2 3 4 5 61 7 8

SIDE VIEW

POSITIONS 6-7:

POSITION 8:

OFF ON

SELECT TAMPER PROTECTION

SETTING (SHOWN

OFF = TAMPER ENABLED).

POSITION 1:

DIP SWITCHES (TYPICAL SETTING:

ALL SWITCHES SHIPPED IN "ON" POSITION) .

SELECT RESPONSE TIME FOR

LOOPS A & B.

(SHOWN ON = SLOW: 400msec).

POSITIONS 2-5:

SELECT ROW OF SERIAL

SWITCH POSITIONS 6 & 7 FOR

CORRECT TABLE TO USE.)

SELECT SERIAL NUMBER TABLE

TO BE USED

6 ON, 7 ON = TABLE 1

6 ON, 7 OFF = TABLE 2

4208SN-001-V0

Figure 3. Dip Switch Settings

PANEL PROGRAMMING

When the 4208SN is used as a zone expander, each of the module

loops that will be used must be assigned to one of the control panel’s

expansion zones. To accomplish this, assign a module loop’s serial

number to a control panel’s expansion zone using procedures

contained in the control panel’s installation instructions. Expansion

zones must be programmed as INPUT TYPE “6”−SL (Serial Number

V-Plex Loop Device), which will enable the control panel to accept the

serial number. Module loops can be programmed in any order and can

be assigned to any legitimate control panel expansion zone.

If enrolling a serial number by faulting its

associated loop, be sure that other V-Plex

loop

dev

ices are not activated, as they may interfere

with the device being enrolled.

When prompted to “enroll” the serial number for a particular zone, you

may enter the serial number for the associated module loop manually

through the keypad, through the V-Link downloader, or by momentarily

.faulting (shorting) and restoring the terminals of the associated

module loop twice when prompted by the keypad. If entering a serial

number manually through the keypad, enter the serial number and

press “*” to advance to the next prompt, which will ask you for the loop

number. Enter a “1” for the loop number for each serial number

entered.

If enrolling or entering a serial number, and the message “Duplicate of

Zone XX” is displayed, another device with that same serial number is

aready in the system. In that case, use a different serial number group

setting on the 4208SN.

If desired, peel the label corresponding to the serial number

assignment table used from the sheet of labels supplied, and apply it to

the outside of the case cover or next to the module for future

reference.

VERIFICATION OF PROGRAMMING

To verify proper 4208SN wiring and programming, fault each of the

module loops that are used and verify that the control panel displays

the correct zone number on the keypad.

WARRANTY

For the latest warranty information, please go to:www.resideo.com

– 3–

Table 1: 4208SN Serial Number Assignments

THE DIP SWITCH SETTINGS PRESET THE LOOPS TO THE APPLICABLE SERIAL NUMBERS

Dip Switch Settings

(6 &7 ON selects serial numbers in this table)

Loop Serial Number

2 3 4 5 6 7 Prefix A B C D E F G H

ON ON ON ON ON ON 006- 5540 5541 5542 5543 5548 5549 5550 5551

ON ON ON ON ON 019- 6612 6613 6614 6615 6620 6621 6622 6623

ON ON ON ON ON 013- 9268 9269 9270 9271 9276 9277 9278 9279

ON ON ON ON 020- 8900 8901 8902 8903 8908 8909 8910 8911

ON ON ON ON ON 027- 8532 8533 8534 8535 8540 8541 8542 8543

ON ON ON ON 034- 8164 8165 8166 8167 8172 8173 8174 8175

ON ON ON ON 041- 7796 7797 7798 7799 7804 7805 7806 7807

ON ON ON 048- 7428 7429 7430 7431 7436 7437 7438 7439

ON ON ON ON ON 055- 7060 7061 7062 7063 7068 7069 7070 7071

ON ON ON ON 062- 6692 6693 6694 6695 6700 6701 6702 6703

ON ON ON ON 069- 6324 6325 6326 6327 6332 6333 6334 6335

ON ON ON 076- 5956 5957 5958 5959 5964 5965 5966 5967

ON ON ON ON 083- 5588 5589 5590 5591 5596 5597 5598 5599

ON ON ON 090- 5220 5221 5222 5223 5228 5229 5230 5231

ON ON ON 097- 4852 4853 4854 4855 4860 4861 4862 4863

ON ON 104- 4484 4485 4486 4487 4492 4493 4494 4495

Table 2: 4208SN Serial Number Assignments

THE DIP SWITCH SETTINGS PRESET THE LOOPS TO THE APPLICABLE SERIAL NUMBERS

Dip Switch Settings

(6 ON, 7 OFF selects serial numbers in this

table)

Loop Serial Number

2 3 4 5 6 7 Prefix A B C D E F G H

ON ON ON ON ON 006- 5796 5797 5798 5799 5804 5805 5806 5807

ON ON ON ON 019- 6868 6869 6870 6871 6876 6877 6878 6879

ON ON ON ON 013- 9524 9525 9526 9527 9532 9533 9534 9535

ON ON ON 020- 9156 9157 9158 9159 9164 9165 9166 9167

ON ON ON ON 027- 8788 8789 8790 8791 8796 8797 8798 8799

ON ON ON 034- 8420 8421 8422 8423 8428 8429 8430 8431

ON ON ON 041- 8052 8053 8054 8055 8060 8061 8062 8063

ON ON 048- 7684 7685 7686 7687 7692 7693 7694 7695

ON ON ON ON 055- 7316 7317 7318 7319 7324 7325 7326 7327

ON ON ON 062- 6948 6949 6950 6951 6956 6957 6958 6959

ON ON ON 069- 6580 6581 6582 6583 6588 6589 6590 6591

ON ON 076- 6212 6213 6214 6215 6220 6221 6222 6223

ON ON ON 083- 5844 5845 5846 5847 5852 5853 5854 5855

ON ON 090- 5476 5477 5478 5479 5484 5485 5486 5487

ON ON 097- 5108 5109 5110 5111 5116 5117 5118 5119

ON 104- 4740 4741 4742 4743 4748 4749 4750 4751

SPECIFICATIONS

Physical:

Width:

6-7/16” (163mm)

Height:

1/4” (108mm)

Depth:

1/4” (32mm)

Electrical:

Current: 33.6mA when polling loop provides power to module;

0.6mA when using external power. See Table 5.

Polling

Loop Voltage:

11V nominal; 8

VDC

range

Power Input (optional): 12VDC @ 33mA (from control

panel’s auxiliary power)

Exp

ander Sensor Loop Response:

Slow:

400msec (all loops)

Fast:

10msec (option for loops A and B)

Note: These currents apply when polling loop input = 11VDC

and 12VDC input is not connected to external

supply.

Sensor Loop Max. Resistance:

Up to 300 ohms of wire

resistance + 10k EOLR.

SEE THE CONTROL PANEL’S INSTALLATION INSTRUCTIONS FOR COMPLETE INFORMATION REGARDING LIMITATIONS OF THE

ENTIRE SECURITY SYSTEM.

Table 5. Current Draw Calculations

Power Input Source (8 – 11VDC)Current Draw (all zones shorted)

From Polling Loop From Control Panel Aux. Power

Polling Loop Only 33.6mA N/A

Polling Loop and External Power Input

0.6mA 33mA

Do not use a remote power supply. On commercial fire panels, when using optional aux. power

and ground from the control, do not additionally connect the polling loop ground to this device.

For UL Listed Commercial Fire Usage:

Use N.O. contacts. Style B, supervise these loops using Model

# EOL 100 fire listed 10k EOLRs (purchased separately).

For UL Listed Commercial Burglary Usage:

Use N.O. or N.C. contacts. Supervise using EOLRs supplied

FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENTS

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual.

Unauthorized changes or modifications could void the user's authority to operate the equipment.

CLASS B DIGITAL DEVICE STATEMENT

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

INDUSTRY CANADA (IC) STATEMENTS

This device complies with RSS210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Responsible Party / Issuer of Supplier’s Declaration of Conformity: Ademco Inc., a subsidiary of Resideo Technologies, Inc., 2 Corporate Center Drive., Melville, NY

11747, Ph: 516-577-2000.

The product should not be disposed of with other household waste. Check for the nearest authorized collection centers or authorized recyclers. The correct disposal of