Renesas REJ06B0732-0100 Installation and operating instructions
APPLICATION NOTE
REJ06B0732-0100/Rev.1.00 March 2008 Page 1 of 13
SH7211 Group
Data Transfer between On-chip RAM Areas with DMAC (Cycle-Stealing Mode)
Introduction
This application note describes the operation of the DMAC, and is intended for reference to help in the design of user
software.
Target Device
SH7211
Contents
1. Introduction ....................................................................................................................................... 2
2. Description of Sample Application.................................................................................................... 3
3. Documents of Reference................................................................................................................ 11
SH7211 Group
Data Transfer between On-chip RAM Areas with DMAC (Cycle-Stealing Mode)
REJ06B0732-0100/Rev.1.00 March 2008 Page 2 of 13
1. Introduction
1.1 Specification
•DMAC channel 0 is used.
•Auto-request mode is used as the interrupt source for activating DMA transfer.
•Cycle-stealing mode is used as the bus mode.
1.2 Used Module
•Direct memory access controller (DMAC channel 0)
1.3 Applicable Conditions
•Microcontroller: SH7211
•Operating Frequency: Internal clock 160 MHz
Bus clock 40 MHz
Peripheral clock 40 MHz
•C Compiler: SuperH RISC engine family C/C++ compiler package Ver.9.01,
from Renesas Technology
SH7211 Group
Data Transfer between On-chip RAM Areas with DMAC (Cycle-Stealing Mode)
REJ06B0732-0100/Rev.1.00 March 2008 Page 3 of 13
2. Description of Sample Application
In this sample application, the direct memory access controller (DMAC) is set to auto request mode to transfer 512-
Kbtyte data stored in the on-chip RAM to another address.
2.1 Operation of Modules Used
When a DMA transfer request is made, the DMAC starts to transfer data in accordance with the priority order of
channels and continues the transfer operation until the transfer end condition is met. Transfer requests for the DMAC
are of three kinds: auto requests, external requests, and on-chip peripheral module requests. The bus mode is selectable
as burst mode or cycle-stealing mode.
For details on the DMAC, refer to the section on the direct memory access controller in the SH7211 Group Hardware
Manual.
An overview of the DMAC is given in table 1. Examples of DMA transfer in cycle-stealing mode and burst mode are
shown in figures 1 and 2, respectively. In addition, a block diagram of the DMAC is shown in figure 3.
Table 1 Overview of DMAC
Item Description
Number of channels 8 (CH0 to CH7)
Only 4 (CH0 to CH3) can receive external requests.
Address space 4 Gbytes
Length of transfer data Byte, word (2 bytes), longword (4 bytes), and 16 bytes (longword ×4)
Maximum transfer count 16,777,216 (24 bits) transfers
Address mode Single address mode and dual address mode
Transfer request External request, on-chip peripheral module request, and auto request
(SCIF: 8 sources, IIC3: two sources, A/D converter: one source, MTU2:
five sources, CMT: two sources)
Bus mode Cycle-stealing mode (normal mode and intermittent mode) and burst
mode
Priority level Channel priority fixed mode and round-robin mode
Interrupt request An interrupt request to the CPU is made when half or all of a transfer
process is completed.
External request detection DREQ input low/high level detection, rising/falling edge detection
Transfer request acknowledge
signal/transfer end signal Active levels for DACK and TEND can be set independently
SH7211 Group
Data Transfer between On-chip RAM Areas with DMAC (Cycle-Stealing Mode)
REJ06B0732-0100/Rev.1.00 March 2008 Page 4 of 13
DREQ
Bus mastership returned to CPU once
Bus cycle
WriteRead WriteRead
CPU CPU CPU DMAC DMAC DMAC DMAC CPUCPU
In the normal mode of cycle stealing, bus mastership is given to another bus master after each DMA
transfer of one transfer unit (byte, word, longword, or 16-byte unit). When a subsequent transfer
request occurs, bus mastership is obtained from the other bus master and transfer proceeds for one
transfer unit. When that transfer ends, the bus mastership is passed to another bus master. This is
repeated until the transfer end condition is satisfied.
The cycle-stealing normal mode can be used in transfer across any interval, regardless of the
requesting source, source, and destination of the transfer.
Figure 1 DMA Transfer Example in Cycle-Stealing Normal Mode
(Dual Address, DREQ Low Level Detection)
DREQ
CPU CPU CPU DMAC DMAC DMAC DMAC CPUCPU
Bus cycle
Read Write Read Write
In burst mode, once the DMAC has obtained bus mastership, it continues to perform transfer without
releasing the bus until the transfer end condition is satisfied. In external mode, however, when the DREQ
signal is being level-detected and changes to the non-active level, even if the tranfer end condition has not
been satisfied, bus mastership is passed to another bus master on completion of the DMA transfer request
for which the request has already been accepted.
Figure 2 DMA Transfer Example in Burst Mode (Dual Address, DREQ Low Level Detection)
SH7211 Group
Data Transfer between On-chip RAM Areas with DMAC (Cycle-Stealing Mode)
REJ06B0732-0100/Rev.1.00 March 2008 Page 5 of 13
DMATCR_n
SAR_n
CHCR_n
DAR_n
DMAOR
DMARS0 to DMARS3
HEIn
DACK0 to DACK3,
TEND0, TEND1
DEIn
RDMATCR_n
RSAR_n
RDAR_n
On-chip
memory
On-chip
peripheral
module
DMA transfer
request signal
DMA transfer acknowledge signal
Interrupt controller
External ROM
External RAM
External device
(memory mapped)
External device
(with acknowledge)
DREQ0 to DREQ3
Peripheral bus
Internal bus
DMAC module
Iteration
control
Register
control
Start-up
control
Request
priority
control
Bus
interface
Bus state
controller
[Legend]
RDMATCR: DMA reload transfer count register CHCR: DMA channel control register
DMATCR: DMA transfer count register DMAOR: DMA operation register
RSAR: DMA reload source address register DMARS0 to DMARS3: DMA extension resource selectors 0 to 3
SAR: DMA source address register HEIn: DMA transfer half-end interrupt request to the CPU
RDAR: DMA reload destination address register DEIn: DMA transfer end interrupt request to the CPU
DAR: DMA destination address register n: 0, 1, 2, 3, 4, 5, 6, 7
Figure 3 Block Diagram of DMAC
SH7211 Group
Data Transfer between On-chip RAM Areas with DMAC (Cycle-Stealing Mode)
REJ06B0732-0100/Rev.1.00 March 2008 Page 6 of 13
2.2 Operational Description of Sample Program
The settings of the DMAC for the sample program are listed in table 4. Also, the operation of the sample program is
illustrated in figure 4.
Table 4 Settings of DMAC
DMA transfer condition Auto request mode
Channel CH0
Length of transfer data 4 bytes
Maximum transfer count 128 transfers (128 ×data length of 4 bytes = 512-byte data)
Address mode Dual address mode
Bus mode Cycle-stealing mode
Priority level Channel priority level fixed mode
Interrupt request Disable an interrupt request to the CPU at the end of a transfer
DMAC H'0xFFF81000
H'0xFFF82000
DAR
SAR
Transfer source
address
On-chip RAM
DMA transfer
512-byte data
512-byte data
Transfer
destination
address
[Legend]
SAR:Source address register
DAR:Destination address register
Figure 4 Operation of Sample Program
SH7211 Group
Data Transfer between On-chip RAM Areas with DMAC (Cycle-Stealing Mode)
REJ06B0732-0100/Rev.1.00 March 2008 Page 7 of 13
2.3 Procedure for Setting Modules
This section describes the procedure for making initial settings when the DMAC is to be used to transfer data between
locations within the on-chip RAM. Auto request mode is used for the transfer requests.
By default, the on-chip peripheral modules of this MCU are in module standby mode. Whenever any of these modules
is to be used, be sure to take it out of module standby mode before making the initial settings. Although processing to
delete the end of DMA transfer is typically handled by interrupts, polling is used in this sample application. A
flowchart of the sample program is shown in figure 5. In addition, a flowchart of DMAC initialization is shown in
figure 6.
For details on registers, refer to the SH7211 Group Hardware Manual.
main
DMAC0.CHCR.BIT.DE = 1
DMAC0.CHCR.BIT.DE = 0
STB.CR2.BIT._DMAC = 0
END
[3]
[4]
[5]
[1]
[2]
No
Yes
No
Yes
DMAC_init
512-byte Initialization
completed?
Transfer completed?
[1] Cancel module standby mode
Activate the DMAC
[2] Initialize the DMAC (channel 0)
[3] Initialize the transfer destination
Clear a 512-byte area to 0
[4] Enable DMA transfer
Set DMA enable flag
[5] Perform DMA transfer end processing
Disable DMA transfer after confirmation
of the tranfer end.
*In this sample application, sleep processing is performed after the main routine is complete.
Figure 5 Flowchart of Sample Program
SH7211 Group
Data Transfer between On-chip RAM Areas with DMAC (Cycle-Stealing Mode)
REJ06B0732-0100/Rev.1.00 March 2008 Page 8 of 13
DMAC_init
END
[3]
[4]
[5]
[6]
[1]
[2]
[1] Disable DMA transfer
Set the DE (DMA enable) bit to 0
Disable DMA transfer
[2] Set the DMA transfer source address (SAR_0)
Specify the DMA transfer source address
[3] Set the DMA transfer destination address (DAR_0)
Specify the DMA transfer destination address
[4] Specify the DMA transfer count (DMATCR_0)
Set the DMA transfer count to 128
[5] Set the channel control register (CHCR_0)
Set TC to B’1: transfer data for the count specified in DMATCR
Set RLD to B’0: disable the reload function
Set RS[3:0] (resource selector) to B’0100: auto request
Set DM[1:0] to B’01: increment the destination address
Set SM[1:0] to B’00: fix the source address
Set TB to B’0: cycle steal mode
Set IE to B’0: disable interrupts
[6] Set the DMA operation register (DMAOR)
Read from the AE and MNIF bits and clear them to 0
Clear the address error flag
Set the DME bit to 1 after clearing the flags
Enable DMA transfer on all the channels
Set DMA channel control register
(CHCR_0)
Set DMA source address register
(SAR_0)
Set DMA destination address
register (DAR_0)
Set DMA transfer count register
(DMATCR_0)
Set DMA channel control register
(CHCR_0)
Set DMA operation register
(DMAOR)
Figure 6 Flowchart of Initializing DMAC
SH7211 Group
Data Transfer between On-chip RAM Areas with DMAC (Cycle-Stealing Mode)
REJ06B0732-0100/Rev.1.00 March 2008 Page 9 of 13
2.4 Register Settings for Sample Program
2.4.1 Clock Pulse Generator (CPG)
The settings of the clock pulse generator for the sample program are described in table 5.
Table 5 Settings of Clock Pulse Generator
Register Name Address Setting Value Description
Frequency control
register (FRQCR) H’FFFE0010 H’1303 CKOEN = “B’1”: output clocks
STC[1:0] = “B’00”: frequency multiplication
ratio of PLL circuit ×1
IFC[2:0] = “B’000”: internal clock ×1
PFC[2:0] = “B’011”: peripheral clock ×1/4
2.4.2 Standby Control Register
The settings of the standby control register for the sample program are described in table 6.
Table 6 Settings of Standby Control Register
Register Name Address Setting Value Description
Standby control
register 2 (STBCR2) H’FFFE0018 H’00 MSTP8 = “B’0”: the DMAC operates
SH7211 Group
Data Transfer between On-chip RAM Areas with DMAC (Cycle-Stealing Mode)
REJ06B0732-0100/Rev.1.00 March 2008 Page 10 of 13
2.4.3 Direct Memory Access Controller (DMAC)
The settings of DMAC registers for the sample program are described in table 7.
Table 7 Settings of DMAC Registers
Register Name Address Setting Value Description
DMA source address
register 0 (SAR) H’FFFE1000 H’FFF81000 Transfer source start address
DMA destination address
register 0 (DAR) H’FFFE1004 H’FFF82000 Transfer destination start address
DMA transfer count
register 0 (DMATCR) H’FFFE1008 D’128 DMA transfer count:
128 transfers
H’0000 0000 Before DMA initialization
DE = “B’0”: disables DMA transfer
H’8000 4410 DMA initialization
TC = “B’1”: transfers data for the count
specified in DMATCR for each transfer
request
DM[1:0] = “B’01”: increments the destination
address
SM[1:0] = “B’00”: fixes the source address
RS[3:0] = “B’0100”: auto request
TB = “B’0”: cycle-stealing mode
TS[1:0] = “B’10”: longword (4 bytes) unit
IE = “B’0”: disables interrupt requests
DE = “B’0”: disables DMA transfer
H’8000 4411 When enabling DMA transfer
DE = “B’1”: enables DMA transfer
DMA channel control
register 0 (CHCR) H’FFFE100C
H’8000 4410 When disabling DMA transfer
DE = “B’0”: disables DMA transfer
DMA operation register
(DMAOR) H’FFFE1200 H’0000 0001 DME = “B’1”: enables DMA transfer on all the
channels
This manual suits for next models
1
Table of contents
Other Renesas Computer Hardware manuals
Renesas
Renesas M16C/6NK User manual
Renesas
Renesas RX72T User manual
Renesas
Renesas M3T-FLX-120NSE User manual
Renesas
Renesas M3A-HS19G50 User manual
Renesas
Renesas RX23T Series User manual
Renesas
Renesas H8/3007 User manual
Renesas
Renesas QB-78K0KX1H-DA User manual
Renesas
Renesas 740 Family Operation instructions
Renesas
Renesas RD74LVC04B User manual
Renesas
Renesas CE2000-H8S Series User manual
Renesas
Renesas RL78/D1A User manual
Renesas
Renesas e1 User manual
Renesas
Renesas RL78/G1F User manual
Renesas
Renesas 7200 Series User manual
Renesas
Renesas RA Series User manual
Renesas
Renesas FP-100A User manual
Renesas
Renesas M3A-HS25 User manual
Renesas
Renesas H8S/2368 Series User manual
Renesas
Renesas H8S Family User manual
Renesas
Renesas M3A-HS37 User manual
Popular Computer Hardware manuals by other brands
EMC2
EMC2 VNX Series Hardware Information Guide
Panasonic
Panasonic DV0PM20105 Operation manual
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 user manual
Gigabyte
Gigabyte B660M DS3H AX DDR4 user manual
Raidon
Raidon iT2300 Quick installation guide
National Instruments
National Instruments PXI-8186 user manual
