Renesas ICS601-21 User manual
ICS601-21 Preliminary 1Revision 010405
Integrated Circuit Systems, Inc. l525 Race Street, San Jose, CA 95126 ltel (408) 297-1201 lwww.icst.com
ICS601-21 Demo Board Instructions
ICS601-21 Demo Board
The ICS601-21 demo board provides a way to quickly evaluate the performance of the ICS601-21 Low
Phase Noise Clock Multiplier.
Power
Connect either 3.3 volts across the VDD and GND header pins.
Frequency Selection
The output frequency can be changed by setting S0, S1 and S2 on SW1 according to the information in the
Multiplier Select Table on page 2 of the datasheet. Alternatively, shunts can be soldered to the appropriate
0604 device landings underneath SW1. Turning on a switch or stuffing a shunt will pull that particular input
low. Opening the switch or removing the shunt will allow the on-chip pull-up resistors to take the input high.
Input Options
The ICS601-21 Demo board supports either a thru hole or an SMT crystal or a single ended clock input.
Crystal Tuning
In order to achieve 0 PPM frequency synthesis, the ICS601-21 supports external tuning capacitors (C1 and
C2). For exact tuning when using a crystal, capacitors should be connected from pins X1 to ground and X2
to ground. The value of these capacitors is given by the following equation, where CLis the specified
crystal load capacitance in pF:
C1 and C2 (pF) = (CL - 5) x 2.
So, for a crystal with 16 pF load capacitance, use two 22 pF caps.
Output Termination
The 50 ohm resistors R3 and R5 as serve as termination resistors to ground. These values match the
PCB’s trace impedance. Component locations R2 and R4 are provided to allow for user experimentation.
This “on-board” termination allows the clock outputs to be measured directly with a high impedance
oscilloscope probe. To use “off-board” termination, remove R3 and R5, connect 50 ohm coax cables
between the clock connectors and the oscilloscope and terminate with 50 ohms in the oscilloscope.
Trace Impedance
The ICS601-21 board has controlled impedance traces of 50 ohms for all clock inputs and outputs.
Component Crystal Input 50 ohm Clock Input
CN1 open SMA connector
R1 open short
C2 open 50 ohm
Y1/Y2 stuff only one open
ICS601-21 Demo Board Instructions
ICS601-21 Preliminary 2Revision 010405
Integrated Circuit Systems, Inc. l525 Race Street, San Jose, CA 95126 ltel (408) 297-1201 lwww.icst.com
Demo Board Schematics
ICS601-21 Demo Board Instructions
ICS601-21 Preliminary 3Revision 010405
PCB Power Plane
PCB Ground Plane
PCB Top
PCB Bottom
Corporate Headquarters
TOYOSU FORESIA, 3-2-24 Toyosu,
Koto-ku, Tokyo 135-0061, Japan
www.renesas.com
Contact Information
For further information on a product, technology, the most
up-to-date version of a document, or your nearest sales
office, please visit:
www.renesas.com/contact/
Trademarks
Renesas and the Renesas logo are trademarks of Renesas
Electronics Corporation. All trademarks and registered
trademarks are the property of their respective owners.
IMPORTANT NOTICE AND DISCLAIMER
RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL
SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING
REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND
OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible
for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3)
ensuring your application meets applicable standards, and any other safety, security, or other requirements. These
resources are subject to change without notice. Renesas grants you permission to use these resources only for
development of an application that uses Renesas products. Other reproduction or use of these resources is strictly
prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property.
Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims,
damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject
to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources
expands or otherwise alters any applicable warranties or warranty disclaimers for these products.
(Rev.1.0 Mar 2020)
© 2020 Renesas Electronics Corporation. All rights reserved.
Table of contents
Other Renesas Computer Hardware manuals
Renesas
Renesas M16C FAMILY User manual
Renesas
Renesas QB-RL78I1A User manual
Renesas
Renesas E2 Lite User manual
Renesas
Renesas Direct Dummy IC M3T-DIRECT80S User manual
Renesas
Renesas Emulation Probe M30850T2-EPB User manual
Renesas
Renesas RZB-ZMD16C-ZDK User manual
Renesas
Renesas QB-RL78G1F User manual
Renesas
Renesas MCU Board for 4513/4514 Group MCUs... User manual
Renesas
Renesas Converter Board R0E436049CFJ10 User manual
Renesas
Renesas H8SX/1520 Series User manual
Renesas
Renesas P9235A-RB User manual
Renesas
Renesas M3S-UFLA32R User manual
Renesas
Renesas SKP16C62P User manual
Renesas
Renesas RZ/V2M User guide
Renesas
Renesas H8/36912 Series User manual
Renesas
Renesas M16C/26A User manual
Renesas
Renesas M32170T-PTC User manual
Renesas
Renesas M3028BT2-CPE User manual
Renesas
Renesas M3T-FLX-DMY613 User manual
Renesas
Renesas M16C FAMILY User manual
Popular Computer Hardware manuals by other brands
EMC2
EMC2 VNX Series Hardware Information Guide
Panasonic
Panasonic DV0PM20105 Operation manual
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 user manual
Gigabyte
Gigabyte B660M DS3H AX DDR4 user manual
Raidon
Raidon iT2300 Quick installation guide
National Instruments
National Instruments PXI-8186 user manual
