Remington G4 Graphite Series User manual

G4 Graphite Series

Personal Groomer

PG4000

I www.remington.co.uk

Visit uk.remington-europe.com/product-registration

You must register within 28 days of purchase.

Thank you for buying your new Remington® product. Please read these instructions

carefully and keep them safe. Remove all packaging before use.

IMPORTANT SAFEGUARDS

• This appliance can be used by children aged from 8 years and above and

persons with reduced physical, sensory or mental capabilities or lack of

experience and knowledge if they have been supervised/instructed and

understand the hazards involved. Children shall not play with the

appliance. Cleaning and user maintenance shall not be done by children

unless they are older than 8 and supervised. Keep the appliance and cable

out of reach of children under 8 years.

• Always check the appliance before you use it. Do not use the appliance if it

is damaged, as this may cause injury.

• The adaptor contains a transformer. Do not cut oﬀ the adaptor to replace it

with another plug, as this causes a hazardous situation.

• WARNING: Keep the appliance dry.

• Do not use the product with a damaged cord.

• WARNING: For recharging the battery, only use the charger supplied with

the appliance - type reference PA-3215U (UK).

• Always replace a damaged adaptor with one of the original type.

• This appliance contains batteries that are non-replaceable.

• Do not use the appliance if it is damaged or malfunctions.

• Do not use attachments other than those we supply.

• This appliance should never be left unattended when plugged into a power outlet,

except when charging.

• Keep the power plug and cord away from heated surfaces.

• Do not plug or unplug the appliance with wet hands.

• Do not twist or kink the cable, or wrap it round the appliance.

• This appliance is not intended for commercial or salon use.

PARTS

1. On/O switch

2. Charging indicator light

3. Charging connector

4. Wide trimmer

5. Adjustable comb

6. Attachment guide combs

7. Precision trimmer

8. Nose, ear, eyebrow trimmer

9. Mini foil shaver

10. Adaptor (not shown)

11. Storage pouch (not shown)

CHARGING YOUR APPLIANCE

This appliance can be used ‘cordless’ by powering it from its internal rechargeable

battery, or ‘corded’ by connecting it to the charging adaptor and then the mains power

supply. Powering the appliance from the charging adaptor is useful if the rechargeable

battery does not have enough charge. Be aware however, that frequent use of the

cordless mode will reduce the life of the rechargeable battery.

Before using your trimmer for the rst time, charge for 10 hours.

1. Ensure the product is switched o.

2. Connect the charging adaptor to the product and then to the mains.

• When charging, the charge indicator light will light up. The light will go out when

charging is complete.

• Your trimmer cannot be overcharged. However, if it is not going to be used for an

extended period of time (2-3 months), unplug it from the mains and store.

• To preserve the life of your batteries, let them run out every 6 months then recharge

for 10 hours.

• On a full charge, your beard trimmer will run for up to 60 minutes of cordless usage.

CORDED

• Connect the charging adaptor to the product and then to the mains.

• Switch your trimmer on.

• We recommend you let the product charge for a few minutes before using corded.

ATTACHMENTS

TO FIT AND REMOVE ATTACHMENTS FIG. A

Ensure that the device is switched o before tting or removing attachments.

• To remove, rotate the attachment anti-clockwise until it unlocks and then lift it o.

• To t, place the desired attachment on top of the device and rotate the attachment

clockwise to lock it into place.

FITTING AND REMOVING FIXED GUIDE COMBS

To Fit

• Hook the front of the guide comb over the teeth of the wide trimmer.

• Press the back of the guide comb down until it clicks into place.

To Remove

• Lift the tab on the back of the guide comb upwards until it comes free from the wide

trimer head.

FITTING AND REMOVING THE ADJUSTABLE COMB

• To t, line up the rails on the comb with the slots on the sides of the groomer and

slide the comb downwards onto the groomer.

• To adjust, press and hold the adjustment button on the back of the comb and slide

the comb up or down. Release the button to lock the comb at that position. The

length of cut is indicated by the scale on the side of the trimmer.

• To remove, press and hold the adjustment button and push the comb up and o the

groomer.

INSTRUCTIONS FOR USE

• Comb facial hair with a ne comb before you start trimming.

• Comb your hair in the direction that it grows so that the hairs are at their maximum

height and facing in the same direction.

• After trimming, lightly go over the trimmed areas with the foil to get a smooth clean

nish.

• Since all hairs do not grow in the same direction, you may want to try dierent

trimming positions (i.e. upwards, downwards or across) for better results.

• Hair should be dry and free from any waxes or lotions.

• If hair builds up during use, switch the unit o, remove any attachment in use and

clean any excess hair clippings from the attachment and groomer.

3DAY STUBBLE, AND BODY HAIR MAINTENANCE

Attachments

Wide trimmer with 1.5 mm xed comb or 3 mm xed comb

Precision trimmer

3-day stubble look:

Let your stubble grow to a length that is slightly longer than the look you are trying to

achieve.

1. Fit the 1.5 mm xed comb to the wide trimmer attachment.

2. Run your trimmer through your beard against the direction of hair growth.

3. Tidy the edges of the stubble using the precision trimmer attachment.

• For more control over the length of your stubble, you can use the adjustable comb

and trim your stubble down in increments starting at a longer length setting until

you get the desired look.

Body hair maintenance

1. Let your hair grow to a length that is slightly longer than the look you are trying to

achieve.

2. Fit the 3mm xed comb to the wide trimmer attachment.

3. Run your trimmer through your body hair against the direction of hair growth.

HAIR CLIPPING

Attachments

Wide trimmer with adjustable comb

Step 1: Nape of the neck

1. Fit the wide trimmer and adjustable comb.

2. Set the adjustable comb to 4 mm or 6 mm.

3. Hold the clipper with the blade teeth pointing upwards. Begin starting at the centre

of the head at the base of the neck.

4. Slowly lift the clipper, working upwards and outwards through the hair, trimming

just a little at a time.

Step 2: Back of the head

• With the comb set at 12mm or 18mm, cut the hair at the back of the head.

Step 3: Side of the head

1. Adjust the comb to a shorter length setting for the areas around the ears.

2. Increase the length setting on the adjustable comb to gradually transition the length

of hair on the side of the head to the longer hair on the top of the head.

Step 4: Top of the head

1. Adjust the comb to the longer length settings (up to 20 mm) then cut the hair on top

of the head against the direction in which the hair normally grows.

2. Always work from the back of the head.

Trim the sideburns

• To trim the sideburns, adjust the comb to the desired length setting, or use one of

the xed guide combs.

SHORT/LONG BEARD TRIMMING

Attachments

Wide trimmer with adjustable comb

Precision trimmer

1. Fit the wide trimmer and adjustable comb.

2. Set the adjustable comb to the desired length.

3. Start trimming under the chin following the line of the jaw.

4. Work upwards towards the ear and upper beard line.

5. Tidy the beard edges using the precision trimmer attachment.

CONTOUR EDGING AND CLOSE HAIR CUTTING

Attachments

Wide trimmer

Contour edging:

1. Hold the device with the cutting blade (teeth) facing you and at 90 degrees to the

skin.

2. Start with the edge of the beard/moustache line and, with the blade resting lightly

against the skin, use slow controlled movements to create contoured lines.

Close hair cutting:

1. Use the ngers of one hand to lift the hair at the base of your head up o your neck.

2. Your index nger should be covering the roots of the hairs you are lifting to prevent

them from being accidentally cut.

3. Hold the trimmer to the base of your neck with the blade facing up. Move the

trimmer up the neck until it touches your index nger which is protecting the hair

roots.

4. Move your trimmer slowly and keep the hair roots at the base of your head out of the

way of the trimmer.

DETAILED NOSE, EYEBROW AND EAR HAIR TRIMMING

Attachments

Nose, ear and eyebrow trimmer

Nose and ear:

1. Fit the nose, ear and eyebrow trimmer.

2. Insert the attachment gently into the nostril or ear.

3. Gently move the attachment in and out while rotating the groomer at the same time.

• Don’t insert the attachment more than 6 mm into the nostril or ear.

Eyebrow:

1. Carefully guide the attachment to remove any stray or longer hairs from the eybrow.

2. To completely remove hairs, let the attachment touch the skin then move over the

desired area.

MICRO STUBBLE AND PRECISION TRIMMING

Attachments

Precision trimmer

Micro stubble:

The attachment has Trim Shave Technology which trims hair down to 0.2 mm to leave a

micro stubble nish.

1. Fit the precision trimmer.

2. Hold the attachment so that the guide on the lower edge of the blade contacts the

skin (in a the same way you as you would hold a wet razor). The guide on the lower

edge of the blade helps to stretch the skin during trimming.

3. Use motions similar to wet shaving.

Precision trimming:

1. Hold the precision trimmer attachment perpendicular to the skin.

2. Move it towards or away from the beard hair to achieve the desired result. Use gentle

pressure and controlled movements.

CLEAN SHAVEN EDGING

Attachments

Mini Foil Shaver

1. Hold the groomer so the mini foil shaver gently touches your face.

2. Use short, well-controlled movements to shave around your beard moustache. Use

your free hand to stretch your skin. This encourages the hair to stand upright,

making it easier to shave.

• Note: The mini foil shaver was designed to shave the detail areas around your beard/

moustache/sideburns. It was not designed to shave your entire face. For a close

comfortable shave, guaranteed, use one of Remington’s electric shavers.

CARE FOR YOUR GROOMER

Care for your product to ensure a long lasting performance. We recommend that you

clean your groomer after each use.

AFTER EACH USE

• Brush any accumulated hairs from the groomer and attachment heads.

• The easiest and most hygienic way to clean the groomer is by detaching the head

from the groomer body and rinsing the head with warm water.

• The groomer body should not be rinsed.

• Place one or two drops of cutter oil or sewing machine oil on the blades.

• Turn the clipper on to distribute the oil evenly, wipe o any excess oil.

BATTERY REMOVAL

We strongly recommend that a professional removes the rechargeable battery. Parts of

the shaver case, and tools have sharp edges and may cause injury if not handled

correctly.

• The rechargeable battery must be removed from the appliance before it is scrapped.

• Disconnect the charging adapter before removing the battery.

1. Ensure the device is discharged of all power. To do this, switch it on and allow it to

run until it stops.

2. Using a suitable tool, carefully pry apart the front and rear halves of the case at the

joint line.

3. Cut the tabs holding the battery to the circuit board.

• Used batteries must be removed from the appliance and disposed of at an

appropriate ocial recycling/collection point.

• Do not attempt to operate the shaver once you have opened it.

RECYCLING

WTo avoid environmental and health problems due to hazardous

substances, appliances and rechargeable and non-rechargeable

batteries marked with one of these symbols must not be disposed of

with unsorted municipal waste. Always dispose of electrical and

electronic products and, where applicable, rechargeable and

non-rechargeable batteries, at an appropriate ocial recycling/

collection point.

SERVICE AND GUARANTEE

Defects aecting product functionality appearing within the

guarantee period will be corrected by replacement or repair at our

option provided the product is used and maintained in accordance

with the instructions. Your statutory rights are not aected.

To claim an extra 1 year guarantee, register your product online

within 28 days of purchase.

Consumables are guaranteed only for their recommended lifecycle. Replacement/spare

parts* are excluded and are only covered by a 1 year warranty.

*Examples include, but are not limited to, adaptors, haircare attachments, grooming accessories, etc.

Other manuals for G4 Graphite Series

This manual suits for next models

Table of contents

Other Remington Trimmer manuals

Remington

Remington RM2520 User manual

Remington

Remington PG-6250 User manual

Remington

Remington RM2700 User manual

Remington

Remington wpg4035 User manual

Remington

Remington Omniblade Multi-Pro User manual

Remington

Remington RM3218H User manual

Remington

Remington HEDGE WIZARD 110946-01 User manual

Remington

Remington RM3218H User manual

Remington

Remington Axcess trimmer RM3017HP User manual

Remington

Remington RM4000 User manual

Remington

Remington BH1822A Instructions for use

Remington

Remington PG6000 User manual

Remington

Remington BHT250 User manual

Remington

Remington RM1822BH User manual

Remington

Remington AXCESS TRIMMER 110946-01A User manual

Remington

Remington MPT1000 User manual

Remington

Remington Nano NE3850 User manual

Remington

Remington Smooth & Silky MPT-3800 User manual

Remington

Remington G2 Graphite Series User manual

Remington

Remington Smooth & Silky WPG-250 User manual

Remington

Remington RM2520 EC User manual

Remington

Remington ST3010A User manual

Remington

Remington PG6300AU User manual

Remington

Remington RM1823BH User manual

Popular Trimmer manuals by other brands

MTD

MTD HT 51 E manual

McCulloch

McCulloch T22 LS Operator's manual

COCKRAFT

COCKRAFT PRO HL36-S Original instructions

Grizzly

Grizzly CT 1800 Li Instructions for use

Peco

Peco Z Trimmer ZT-3000 Operator's manual

Solo

Solo 116 instruction manual

Stiga

Stiga ST 1200 specification

Echo

Echo GT-225 - 10-09 Operator's manual

RedMax

RedMax BT17 owner's manual

GreenWorks

GreenWorks STA806 Operator's manual

Parkside

Parkside PHSL 900 A3 Translation of the original instructions

Gardeo

Gardeo PRO GPTHT2560 Original instructions

Park

Park DT-810870 Operation manual

Worx

Worx WG209 owner's manual

Gardenline

Gardenline 43671/HTKS26 user guide

Makita

Makita 3710 instruction manual

Champion

Champion 100683 Operator's manual

Stihl

Stihl FS 311 instruction manual