Regency P33R-LP2 Quick start guide

FPIFIREPLACEPRODUCTSINTERNATIONALLTD. 6988VentureSt.,Delta,BC Canada,V4G1H4

918-063a

MODELS: P33R-NG2 Natural Gas P33R-LP2 Propane

P33R Zero Clearance Rear Direct Vent

Gas Fireplace

04/26/04

Owners &

Installation Manual

WARNING:

Iftheinformationintheseinstructionsarenotfollowedexactly

a fire or explosion may result causing property damage

personal injury or loss of life.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors an

liquids in the vicinity of this or any other appliance.

Installation and service must be performed by a qualifie

installer, service agency or the gas supplier.

FOR YOUR SAFETY

What to do if you smell gas:

Do not try to light any appliance

Do not touch any electrical switch

do not use any phone in you

building.

Immediately call your gas supplie

from a neighbour's phone. Follow

the gas supplier's instructions.

If you cannot reach your ga

supplier, call the fire department.

Tested by: Installer: Please complete the details on the back cover

and leave this manual with the homeowner.

Homeowner: Please keep these instructions for future reference.

www.regency-fire.com

Regency P33R-2 Zero Clearance Rear Vent Direct Vent Gas Fireplace

To the New Owner:

Congratulations!

Youaretheownerofastate-of-the-artGasStoveby FIREPLACEPRODUCTSINTERNATIONAL.

TheP33R-2isahandcraftedapplianceandhasbeendesignedtoprovideyouwithall thewarmthand

charm of a wood fireplace at the flick of a switch. The model P33R-2 has been approved by Warnock

Hersey for both safety and efficiency. As it also bears our own mark, it promises to provide you with

economy, comfort and security for many trouble free years to follow. Please take a moment now to

acquaintyourselfwith these instructions and the many features ofyourRegency Fireplace.

INFORMATION FOR MOBILE/MANUFACTURED HOMES AFTER FIRST SALE

This Regency product has been tested and listed by Warnock Hersey as a Direct Vent Wall Furnace to the following standards: ANSI Z21.44-

1995, CAN1-2.19-M81, CAN/CGA-2.17-M91 and ANSI Z21.88-1998/CSA 2.33-M98.

This Direct Vent System Appliance must be installed in accordance with the manufacturer's installation instructions and the Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280, or the current Standard of Fire Safety Criteria for Manufactured Home Installations,

Sites, and Communities ANSI/NFPA 501A, and with CAN/CSA Z240-MH Mobile Home Standard in Canada.

This appliance installation must comply with the manufacturer's installation instructions and local codes, if any. In the absence of local codes follow

the current National Fuel Gas Code, ANSI Z223.1 and the current National Electrical Code ANSI/NFPA 70 in the U.S.A., and the current CAN/CGA

B149 Gas Installation Code and the current Canadian Electrical Code CSA C22.1 in Canada.

ThisRegencyMobile/ManufacturedHomeListed

appliance comes factory equipped with a means

to secure the unit.

This Regency Mobile/Manufactured Home listed

appliance comes equipped with a dedicated #8

ground lug to which an 18 gauge copper wire

from the steel chassis ground must be attached.

This appliance may be installed in an aftermar-

ket permanently located, manufactured (mobile)

home, where not prohibited by local codes.

This appliance is only use with the type of gas

indicated on the rating plate. This appliance is

notconvertibleforusewithothergases,unlessa

certified kit is used.

Regency P33R-2 Zero Clearance Rear Vent Direct Vent Gas Fireplace 3

TABLE OF CONTENTS

Operating Instructions

LightingPlateInstructions .........................................28

OperatingInstructions ...............................................29

LightingProcedure ....................................................29

ShutdownProcedure .................................................29

First Fire ...................................................................29

AerationAdjustment..................................................29

NormalOperatingSoundsof

GasAppliances ..................................................30

Maintenance

MaintenanceInstructions ..........................................30

GeneralVentMaintenance ........................................30

Gold-PlatedorBrassLouvers ....................................30

Gold Plated or Brass Trim .........................................30

LogReplacement ......................................................30

Thermopile/Thermocouple .........................................31

Glass Gasket............................................................31

Door Glass: Flush and Bay Glass .............................31

RemovingValve .........................................................32

InstallingValve ..........................................................32

PartsList

Replacement/SparePartsList...................................33

Warranty

Warranty ...................................................................39

Safety Label

SafetyLabel ............................................................... 4

Installation

ImportantMessage .................................................... 5

BeforeYouStart ........................................................ 5

GeneralSafetyInformation ......................................... 5

ManufacturedHomeAdditionalRequirements ............ 5

InstallationChecklist .................................................. 6

UnitDimensions......................................................... 6

HeatWaveDuctSystemOption.................................. 6

LocatingYourGasStove............................................ 6

Clearances................................................................. 7

CombustibleMantelClearances................................. 7

MantelLegClearance ................................................ 7

FramingandFinishing................................................ 8

Unit Assembly Prior to Installation ............................. 9

ExteriorVentTerminationLocations..........................10

VentingIntroduction ..................................................11

Venting - Regency Direct Vent System (Flex)

HorizontalTerminationsonly...............................11

Venting-Installation of Regency Direct Vent

System (Flex) ..............................................12

Venting - Simpson Dura-Vent System.......................13

SimpsonDura-VentComponentsList .................13

VentingArrangements-HorizontalTerminations.14

VentingArrangements-VerticalTerminations ....15

VerticalTerminations-Co-LinearFlexSystem ...16

VentingArrangements..................................17

Venting-HorizontalInstallations.........................18

Venting-VerticalTermination .............................19

GasLineInstallation..................................................19

Pilot Adjustment .......................................................20

HighElevation ...........................................................20

System Data.............................................................20

Gas Pipe Pressure Test ............................................20

SITValveDescription ................................................20

ConversiontoPropane ..............................................21

Optional Brick Panels ...............................................22

LogInstallation..........................................................22

FlushDoor-Standard ...............................................23

OptionalFlushTrim...................................................23

Louvers-Flush..........................................................24

DoubleScreenDoor ..................................................24

OptionalBayFront ....................................................24

OptionalBayTrim .....................................................24

Louvers-Bay ............................................................25

RemoteControl(optional)..........................................25

WallThermostat(optional) ........................................25

Remote Wall Switch..................................................25

WiringDiagram .........................................................26

OptionalFanInstallation............................................27

Regency P33R-2 Zero Clearance Rear Vent Direct Vent Gas Fireplace

This is a copy of the label that accompanies

each P33R-2 Zero Clearance Direct Vent Gas

Fireplace. We have printed a copy of the con-

tents here for your review. The safety label is

located on the front inside base of the unit,

visible when the bottom louver is open.

NOTE: Regency units are constantly being

improved.Checkthelabelontheunitandifthere

isadifference,thelabelontheunitisthecorrect

one.

SAFETY LABEL

FortheStateofMassachusetts,installation

and repair must be done by a plumber or

gasfitter licensed in the Commonwealth of

Massachusetts.

For the State of Massachusetts, flexible

connectors shall not exceed 36 inches in

length.

For the State of Massachusetts, the appli-

ances individual manual shut-off must be a

t-handle type valve.

Regency P33R-2 Zero Clearance Rear Vent Direct Vent Gas Fireplace 5

INSTALLATION

IMPORTANT:

SAVE THESE

INSTRUCTIONS

The P33R-NG2 or P33R-LP2 Direct Vent Fire-

place must be installed in accordance with these

instructions. Carefully read all the instructions in

this manual first. Consult the "authority having

jurisdiction"todeterminetheneedforapermitprior

tostartingtheinstallation.Itistheresponsibilityof

the installer to ensure this fireplace is installed in

compliance with manufacturer's instructions and

all applicable codes.

BEFORE YOU START

Safeinstallationandoperationof thisappliance

requires common sense, however, we are

required by the Canadian Safety Standards

and ANSI Standards to make you aware of the

following:

YOUNG CHILDREN SHOULD BE

CAREFULLY SUPERVISEDWHEN

THEYAREINTHESAMEROOMAS

THEAPPLIANCE.

CLOTHINGOROTHER FLAMMA-

BLEMATERIALSHOULDNOTBE

PLACEDONORNEARTHEAPPLI-

ANCE.

INSTALLATION AND REPAIR

SHOULD BE DONE BY A QUALI-

FIEDSERVICEPERSON.THEAP-

PLIANCESHOULDBEINSPECTED

BEFOREUSEANDATLEASTAN-

NUALLY BY A PROFESSIONAL

SERVICE PERSON. MORE FRE-

QUENT CLEANING MAY BE RE-

QUIREDDUETOEXCESSIVELINT

FROMCARPETING,BEDDINGMA-

TERIAL, ETC. IT IS IMPERATIVE

THAT CONTROL COMPART-

MENTS,BURNERSANDCIRCULAT-

ING AIR PASSAGEWAYS OF THE

APPLIANCEBEKEPTCLEAN.

DUE TO HIGH TEMPERATURES,

THEAPPLIANCESHOULDBELO-

CATED OUT OF TRAFFIC AND

AWAY FROM FURNITURE AND

DRAPERIES.

WARNING:FAILURETOINSTALL

THIS APPLIANCE CORRECTLY

WILLVOIDYOURWARRANTYAND

MAY CAUSE A SERIOUS HOUSE

FIRE.

CHILDRENANDADULTSSHOULD

BE ALERTED TO THE HAZARDS

OF HIGH SURFACE TEMPERA-

TURES, ESPECIALLY THE FIRE-

PLACE GLASS, AND SHOULD

STAYAWAYTOAVOIDBURNSOR

CLOTHINGIGNITION.

GENERAL SAFETY

INFORMATION

1) The appliance installation must conform

with local codes or, in the absence of local

codes, with the current Canadian or

National Gas Codes, CAN1-B149 or

ANSI Z223.1 Installation Codes.

2) The appliance when installed, must be

electrically grounded in accordance with

local codes, or in the absence of local

codes with the current National Electrical

Code,ANSI/NFPA 70 or CSAC22.1 Cana-

dian Electrical Code.

3) See general construction and assembly

instructions.Theapplianceandventshould

be enclosed.

4) This appliance must be connected to the

specified vent and termination cap to the

outside of the building envelope. Never

vent to another room or inside a building.

Make sure that the vent is fitted as per

Venting instructions.

5) Inspect the venting system annually for

blockage and any signs of deterioration.

6) Ventingterminalsshallnotberecessedintoawall

or siding.

7) Any safety glass removed for servicing

must be replaced prior to operating the

appliance.

8) To prevent injury, do not allow anyone who

is unfamiliar with the operation to use the

fireplace.

9) Wear gloves and safety glasses for pro-

tection while doing required maintenance.

10)Be aware of electrical wiring locations in

walls and ceilings when cutting holes for

termination.

11)Under no circumstances should this appli-

ance be modified. Parts that have to be

removed for servicing should be replaced

prior to operating this appliance.

12)Installation and any repairs to this appli-

anceshouldbe donebyaqualifiedservice

person. A professional service person

should be called to inspect this appliance

annually. Make it a practice to have all of

your gas appliances checked annually.

13)Do not slam shut or strike the glass door.

14)Under no circumstances should any solid

fuels (wood, paper, cardboard, coal, etc.)

be used in this appliance.

15)Theapplianceareamustbekeptclearand

free of combustible materials, (gases and

other flammable vapours and liquids).

MANUFACTURED

MOBILE HOME

ADDITIONAL

REQUIREMENTS

1) Ensure that structural members are not cut

or weakened during installation.

2) Ensure proper grounding using the #8

ground lug provided. See page 26.

Emissions from burning wood or gas could

contain chemicals known to the State of

California to cause cancer, birth defects or

other reproductive harm.

Regency P33R-2 Zero Clearance Rear Vent Direct Vent Gas Fireplace

INSTALLATION

CHECKLIST

1) Locate appliance

a) Room location, page 6

b) Clearances to Combustibles, page 6

c) Mantle Clearances, page 7

d) Framing&Finishing Requirements,

page 8

e) Venting Requirements, pages 10 to 15.

2) Assemble Top Facing Support and Side

NailingStrips,page8.(NOTE:mustbedone

before installing unit into fireplace.)

3) Install vent, pages 10 to 19.

4) Make gas and electrical connections. Test

the pilot. Must be as per diagram. Page 20.

Convert to Propane if desired, page 21.

5) Install brick panels (optional), page 22.

6) Installlogsandembersandrockwoolwhere

indicated on page 22.

7) Install Flush Door Front (Standard) and

optional Flush Gold Trim, page 23.

8) Install optional Double Screen Door, page

24.

9) Install Optional Bay Front and optional Bay

Gold Trim, page 24.

10)Install Louvers (Flush or Bay), pages 24

and 25.

11)InstalloptionalWallSwitch,RemoteControl,

or Wall Thermostat, page 25.

11)Install Optional Fan, page 27.

13)Final check.

Before leaving this unit with the customer, the

installer must ensure that the appliance is firing

correctly and operation fully explained to

customer.

This includes:

1) Clocking the appliance to ensure the cor-

rect firing rate (rate noted on label) after

burning appliance for 15 minutes.

2) If required, adjusting the primary air to

ensurethattheflame does notcarbon.First

allow the unit to burn for 15-20 min. to

stabilize.

CAUTION: Any alteration to the product

that causes sooting or carboning that

results in damage is not the responsibil-

ity of the manufacturer.

Diagram 1

INSTALLATION

LOCATING YOUR

GAS STOVE

1) When selecting a location for your stove,

ensure that the clearances outlined on this

page are met.

2) Provide adequate clearances for servicing.

3) The appliance must be installed on a flat,

solid, continuous surface (e.g. wood, met-

al, concrete). This may be the floor, or

raiseduponaplatformtoenhanceitsvisual

impact. If the appliance is going to be in-

stalled on carpeting, combustible linoleum

tileorothercombustible material other than

wood flooring, the appliance must be in-

stalled on a metal or wood panel extending

the full width and depth of the appliance.

4) The P33R-2 Direct Vent Gas Fireplace can

beinstalledinarecessedpositionorframed

out into the room as in A, B, C, D. See Dia.

UNIT DIMENSIONS 5) Thisappliance is Listed forbedroom instal-

lations when used with a Listed Millivolt

Thermostat. Some areas may have further

requirements, check local codes before

installation.

6) The P33R-2 Direct Vent Gas Fireplace is

approved for alcove installations, which

meet the clearances listed on this page.

7) We recommend that you plan your installa-

tion on paper using exact measurements

for clearances and floor protection before

actually installing this appliance. Have a

qualified inspector, dealer, or installer re-

view your plans before installation.

Note: For vent terminations see page 10.

A) Flat on Wall

B) Flat on Wall Corner

C) Recessed into Wall/Alcove

D) Corner

DUCT SYSTEM

OPTION

KIT #946-556

The HeatWave Air Duct Kit increases the

effectiveness of your fireplace by dispersing

warm air from the fireplace to remote locations

inthesameroom or other rooms inyour home.

Upto twokitsmaybeinstalledonthefireplace.

Please Note: Only 1 HeatWave kit may be

operatedat onetime.Thisincludestheinternal

blower option as well.

Regency P33R-2 Zero Clearance Rear Vent Direct Vent Gas Fireplace 7

COMBUSTIBLE MANTELS

INSTALLATION

Clearances for Bay or Flush Front

WARNING

Fire hazard is an extreme risk if

these clearances are not ad-

hered to.

Because of the extreme heat this fireplace emits, the mantel clearances are critical.

Combustible mantel clearances from top of unit are shown in the diagram below.

Note: A non-combustible mantel may be installed at a lower height if the framing is

made of metal studs covered with a non-combustible board.

MANTEL LEG CLEARANCES

Combustible mantel leg clearances as per diagram below:

This drawing is to scale at 1:6 (one inch = 6 inches). Mantel can be installed anywhere in shaded

area or higher using the above scale.

Note: Ensure the paint that is used on the mantel and the facing is "heat resistant"

or the paint may discolour.

CLEARANCES

The clearances listed below are Minimum dis-

tances unless otherwise stated:

A major cause of chimney related fires is

failure to maintain required clearances

(air space) to combustible materials. It is

of the greatest importance that this fire-

place and vent system be installed only in

accordance with these instructions.

Clearance to Combustibles from:

Back 0" (0mm)

Side 0" (0mm)

Floor 0" (0mm)

NOTE: The minimum floor clearance must be

maintained from the top surface of the carpet-

ing, tile, etc.

Minimum Clearance from Top of Unit to:

Mantel* min.7" (177mm)

Ceiling 30" (762mm) from

top of unit.

Side Wall Clearance

Bay or Flush Front 7-1/2" (191mm)

Maximum

1-1/2"

projection at

2"minimum

clearance.

The HeatWave Duct Kit has different

clearance and framing requirements,

check the HeatWave manual for details.

Vent 1-1/2" (38mm) Flex

1-1/4" (32mm) Simpson Dura-Vent

Alcove Clearances:

Max. Depth 36" (914mm)

Min. Width 48" (1219mm)

Min. Height 59" (1499mm)

* see mantle clearance instructions (page 7).

Regency P33R-2 Zero Clearance Rear Vent Direct Vent Gas Fireplace

INSTALLATION

InstallSideNailingStrips, and Top Facing

Support before unit is slipped into

position. See page 9 for assembly

details.

3) For exterior walls, insulate the enclosure to

the same degree as the rest of the house,

apply vapour barrier and drywall, as per

local installation codes. (Do not insulate

the fireplace itself.)

4) The top of the unit must not be closer than

30" (762mm) to the ceiling.

5) Combustiblematerial may bebroughtup to

thetopandsidesoftheunitandbecovered

with ceramic tiles, bricks, rock or other

suitable combustible finishing materials.

Note: The unit does not have to be com-

pletely enclosed in a chase. The

clearance on top of the unit is 0" to

the standoffs so combustible

building materials can be laid di-

rectly on top of the standoffs. You

must maintain 1-1/2" (38mm) clear-

ance from the vent to combustible

materials for flex (1-1/4" for Simp-

son Dura-Vent).

1) Determine the total thickness of facing

material (e.g. drywall plus ceramic tiles) to

allow the finished surface to be flush with

the front of the unit. Total facing thickness

canvaryfrom1/2"(13mm)to1-1/4"(32mm)

thick.

6) Use steel studs for framing where the

1-1/2" (38mm) clearance from the vent to

combustiblematerialcannotbemaintained.

2) Frame in the enclosure for the unit with

framing material.

Vertical Termination or

Vertical Rise with Horizontal

Termination

Rear Termination

FRAMING AND FINISHING

NOTE:Ifthisisanoutsidecorner,theminimum

distance between the vent and the outside

corner is 6" (15cm) with AstroCap termination

cap or 12" (30cm) with Dura-Vent termination

cap.

NOTE: If this is an outside corner, the minimum

distance between the vent and the outside

corner is 6" (15cm) with AstroCap termination

cap or 12" (30cm) with Dura-Vent termination

cap. The HeatWave Duct Kit has different

clearance and framing requirements,

check the HeatWave manual for details.

Regency P33R-2 Zero Clearance Rear Vent Direct Vent Gas Fireplace 9

"C" Screw Position:

For a facing material depth of

1-1/4"(32mm), the top facing

support must be reversed.

TheTopFacingSupport,theSideNailingStrips

and the 2 Top Standoffs must be correctly

positioned and attached to the top before unit

is slipped into position.

TopStandoffAssembly

The top standoffs are shipped in a flat position

and must be pulled up and bent into the correct

shape. Setup each of the 2 Top Standoff by

bendingupatthebendlinesuntilthescrewhole

in the standoff and the pre-punched screw

holesonthetoplineup.Use threemorescrews

per standoff to attach securely to the top.

Top Facing Support &

Side Nailing Strips

Determine the total thickness of facing material

(e.g. drywall plus ceramic tiles) to allow the

finished surface to be flush with the front of the

unit. Total facing thickness can vary from 1/2"

(13mm) to 1-1/4" (32mm) thick.

The Top Facing Support & Side Nailing Strips

canbemountedin3differentpositionsdepend-

ing on the thickness of the facing material.

Screw FacingMaterial

Position Depth

A 1/2" /13mm

B 7/8" /22mm

C*1-1/4" /32mm

*For "C" screw position the top facing support

is reversed.

1) Mount Top Facing Support using the 3

suppliedscrewsintothethree pre-punched

screw holes on the top front of the unit. Use

holepositions A, B, orC dependingonyour

facing depth.

2) Use the same screw hole position for the

Side Nailing Strips as was used for the Top

Facing Support. Attach each side nailing

strip using 3 screws.

UNIT ASSEMBLY

PRIOR TO INSTALLATION

INSTALLATION

Regency P33R-2 Zero Clearance Rear Vent Direct Vent Gas Fireplace

EXTERIOR VENT TERMINATION LOCATIONS

INSTALLATION

Fixed

Openable

Closed Closed

Openable

Vertical

Termination

Vent terminal Area where terminal is not permited

Air supply outlet

24"

Inside

corner detail

24"

18"

Vertical

Termination

A= Clearance above grade, veranda, porch, deck, or balcony *(min. 12"/30cm)

B= Clearance to window or door that may be opened *(12"/30cm)

C= Clearance to permanently closed window *(min. 12"/30cm)

D= Vertical clearance to ventilated soffit located above the terminal within a horizontal

distance of (24"/60cm) from the centerline of the terminal (min. 18"/46cm) check with

local code.

E= Clearance to unventilated soffit (min. 15"/38cm)

F= Clearance to outside corner: with AstroCap Termination Cap (min. 6"/15cm), with

Dura-Vent Termination Cap (12"/30cm)

G= Clearance to inside corner: with AstroCap TerminationCap(min.6"/15cm), with Dura-

Vent Termination Cap (12"/30cm)

H= Nottobeinstalledaboveameter/regulatorassemblywithin(3'/90cm)horizontallyfrom

the centerline of the regulator.

J= Clearance to service regulator vent outlet *(min. 36"/90cm)

K= Clearance to non-mechanical air supply inlet to building or the combustion air inlet to

any other appliance *(12"/30cm)

L= Clearance to a mechanical air supply inlet *(min. 72"/1.8m)

M= Clearance above paved sidewalk or a paved driveway located on public property

*(min. 84"/2.1m)

N= Clearance under veranda, porch, deck, or balcony *(min. 12"/30cm)

Note:

- A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings.

- Only permitted if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the floor.

- If the vent termination is accessible, a certified guard shall be installed.

* As specified in CGA B149 Installation Code. Note: Local codes or regulations may require different clearances.

This manual suits for next models

Table of contents

Other Regency Indoor Fireplace manuals

Regency

Regency City CV60EPV-NG Quick start guide

Regency

Regency E18-NG Quick start guide

Regency

Regency Classic i2450 User manual

Regency

Regency U30-NG and User manual

Regency

Regency Z2510L Quick start guide

Regency

Regency Panorama P121 Quick start guide

Regency

Regency P42-LP3 Quick start guide

Regency

Regency Liberty LRI6E-NG11 Quick start guide

Regency

Regency P36-NG4 Quick start guide

Regency

Regency HZ54E-NG10 Quick start guide

Regency

Regency Classic I2405M Quick start guide

Regency

Regency Cascades I2500 User manual

Regency

Regency L540PB Service manual

Regency

Regency L540E-NG1 Quick start guide

Regency

Regency L676S-LP1 Sunrise User manual

Regency

Regency P48-2 Quick start guide

Regency

Regency Cardinia F150B-1 Quick start guide

Regency

Regency U31-NG3 Quick start guide

Regency

Regency classic i2400m Service manual

Regency

Regency GEM54-NG Quick start guide

Regency

Regency E21-LP1 Quick start guide

Regency

Regency Alterra CI1150 Quick start guide

Regency

Regency Liberty L234 Series Quick start guide

Regency

Regency City CV60E Series Quick start guide

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual