Regency HZ33CE-LP10 User manual

34-9/16"

16"

407mm

23"

584mm

[878mm]

26-1/16"

(662mm)

(406mm)

16"

NAILING STRIP

2-1/2"

[64mm]

742mm

29-1/4"

21-3/8"

543mm

26"

660mm

29-7/16"

747mm

742mm

29-1/4"

(76mm)

HZ33CE Gas Fireplace

Opening for gas

connection

Floor

DETAIL N

SCALE 1:6

2X4HEADER

Non-combustibl

Header

(steel stud

on edge)

* Measured from base of unit.

Model HZ33CE-NG10 HZ33CE-LP10

Fuel Type Natural Gas Propane

Minimum Supply Pressure 5” W.C. (1.25 kPa) 11” W.C. (2.73 kPa)

Manifold Pressure - High 3.5” W.C. (0.87 kPa) 10” W.C. (2.48 kPa)

Manifold Pressure - Low 1.6” W.C. (0.41 kPa) 6.4” W.C. (1.59 kPa)

Orice Size -Altitude 0-4500 ft. #47 DMS #56 DMS

Minimum Input

Altitude 0-4500 ft. (0-1372m)

12,000 BTU/h

(3.51 kW)

12,500 BTU/h

(3.66 kW)

Maximum Input

Altitude 0-4500 ft. (0-1372m)

17,000 BTU/h

(4.98 kW)

15,000 BTU/h

(4.39 kW)

Vent Sizing 4” x 6-7/8” - Flex

4” x 6-5/8” - Rigid

4” x 6-7/8” - Flex

4” x 6-5/8”- Rigid

Approved Venting Systems

Flex Vent Systems: FPI AstroCap™ Flex Vent

Rigid Pipe Vent Systems: Simpson Direct Vent Pro®

American Metal Products® Amerivent Direct

Security Secure Vent®

Selkirk Direct-Temp™

Metal-Fab® Sure Seal

34-9/16"

16"

407mm

23"

584mm

[878mm]

26-1/16"

(662mm)

(406mm)

16"

NAILING STRIP

2-1/2"

[64mm]

742mm

29-1/4"

21-3/8"

543mm

26"

660mm

29-7/16"

747mm

742mm

29-1/4"

(76mm)

Framing

Dimensions

Description HZ33CE

G Framing Width 35"(889mm)

H Framing Height * 31-3/4" (806mm)

I Framing Rise from Floor 0" (when not using a surround)

2" min (when using Casandra Surround )

3-5/16" min (when using Verona Faceplate)

J * For Finish with

Tile Surround

Framing Depth Vertical

Horizontal

22-3/4" (578mm) Vertical Rise

19-3/4" (502mm) Rigid / 16" (406mm) Flex

K Corner Wall Length 38-15/16" (988mm)

L Corner Facing Wall Width 55-1/2" (1410mm)

M Framed Chase Ceiling* 36" (914mm) Rigid 32"

(812mm)

Flex

NVent Centerline Height* 30" (762mm) Rigid 26"

(660mm)

Flex

OGas Connection Height* 1 1/2" (38mm)

P Gas Connection Inset* 7-3/16" (183mm)

Q Gas Connection Width* 3" (76mm)

HZ33CE Gas Fireplace

Caution Requirements

The top, back and sides of the ﬁreplace are deﬁned by

standoffs. The metal ends of the standoff may NOT

be recessed into combustible construction.

WARNING

Fire hazard is an extreme risk

if these clearances (air space) to combustible materials are not

adhered to. It is of greatest importance that this replace and vent

system be installed only in accordance with these instructions.

CLEARANCES

The clearances listed below are Minimum distances unless otherwise stated:

A major cause of chimney related res is failure to maintain required clearances (air space) to combustible materials. It is of the greatest

importance that this replace and vent system be installed only in accordance with these instructions.

Clearance: Dimension Measured From:

A: *Front Floor Clearance (min.) 0" Underside of Unit

B: *Sidewall (on one side) 9" (229mm) Side Opening of Unit

C: *Ceiling

(room and/or alcove) 30" (762mm) Top Opening of Unit

D: Alcove Width 84" (1219mm) Sidewall to Sidewall (Minimum)

E: Alcove Depth 36" (914mm) Front to Back Wall (Maximum)

F: Mantel 12" (305mm)

G:Mantel Clearances 15-3/4" (400mm) From Top Opening of Unit

Close to Ceiling

Flue Clearances

Horizontal - Top 2-1/2"

Horiztonal - Side 1-1/2"

Horiztonal - Bottom 1-1/2"

Vertical (Flex Vent) 1-1/2"

Vertical (Rigid) 1-1/4"

HZ33CE Gas Fireplace

MANTEL CLEARANCES

Note: Ensure the paint that is used on the mantel

and the facing is "heat resistant" or the

paint may discolour.

MANTEL LEG CLEARANCES

Combustible mantel leg clearances from side of unit as per diagram:

Top View

0-3

Allowable mantel leg projection

6-3/4"

Side opening of Unit

Due to the extreme heat this replace emits, the

mantel clearances are critical. Combustible mantel

clearances from top of front facing are shown in the

diagram on the right.

Note: A non-combustible mantel may be

installed at a lower height if the framing

is made of metal studs covered with a

non-combustible board.

Drywall

Mantel Clearances

12 64

810

Top opening

of Unit

12" (305mm)

0 - 3-1/2" (89mm)

7-1/2"(191mm)

15-3/4" (400mm)

11-3/4"(298mm)

13-3/4"(349mm)

24-1/4"(616mm)

to floor

3"(76mm)

Standoff

Side View

Non-combustible material

FRAMING & FINISHING

1. Frame in the enclosure for the unit with framing material.

Note: When constructing the framed opening, please ensure there is access to install the gas lines when the unit is installed.

2. For exterior walls, insulate the enclosure to the same degree as the rest of the house; apply vapour barrier and drywall, as per local installation codes.

(Do not insulate the replace itself.)

WARNING: Failure to insulate and add vapor barriers to the inside of the exterior wall will result in operational and performance problems

including, but not limited to: excessive condensation on glass doors, poor ame package, carbon, blue ames etc. These are not product

related issues.

3. The unit does not have to be completely enclosed in a chase. You must maintain clearances from the vent to combustible materials: See "Clearances"

section. Combustible materials can be laid against the side and back standoffs and the stove base.

4. Tile Finish Option 1: Drywall may be installed onto the unit as shown below to create a surface to apply ﬁnishing materials such as tile, slate, etc.

Drywall cannot extend beyond the metal surface of the unit.

5. Tile Finish Option 2: If applying a non-combustible ﬁnishing material (tile,slate,etc) the material can be installed directly onto the metal surface (clean

front) of the unit in the area shown below.

29-7/16"

747mm

21-3/8"

[542mm]

Nailing strip for Tile

Finish (set back 1/2")

Nailing strip for Clean

Finish (set ush with

unit)

TILE FINISH

1. There are 8 (eight) side nailing strips and one top nailing strip available on the unit. One set of four (4) are for a clean ﬁnish installation, the other set

are for a tile ﬁnish installation as they are set back 1/2" (13mm). The top nailing strip is adjustable to 1/2" (13mm).

2. Bend the required four (4) nailing strips to 90º.

3. Attach top nailing strip with one (1) screw (located at the back of the nailing strip). Adjust to required position, flush or back 1/2" and tighten screw.

Nailing strip for Tile

Finish (set back 1/2")

Nailing strip for Clean

Finish (set ush with

unit)

Adjustable Top Nailing

Strip

Combustible

Material

Non-combustible

Finishing Material

(ie. tile)

Non-combustible Material (3-1/2" x 34-9/16")

Finishing Material

(ie. tile)

Nailing Strip -1/2" back from unit face

Combustible

Material

Non-combustible Supplied with Unit

1-1/2

(38mm)

Ensure finished

material is

brought to lip

HZ33CE Gas Fireplace

29-7/16"

747mm

21-3/8"

[542mm]

NO FACING OR

FINISHING MATERIAL

IN THIS AREA

No Combustible

Materials in this Area

33-7/16"

[849mm]

34-9/16"

878mm

2-1/2"

[64mm]

5-3/16"

[132mm]

NON COMBUSTIBLE BOARD SUPPLIED WITH UNIT 3-1/2"

[89mm]

29-7/16"

747mm

21-3/8"

[542mm]

J Style trim or metal

corner bead may be

used to finish edges

No Combustible

Materials in this Area

1/2" DRYWALL

NON-COMBUSTIBLE FACING

FOR CLEAN LOOK

(ie. PAINTED FINISH)

34-9/16"

878mm

33-7/16"

[849mm]

1/2" DRYWALL

DO NOT EXTEND

DRYWALL ONTO METAL

SURFACE OF UNIT.

WOOD STUD

NON COMBUSTIBLE BOARD SUPPLIED WITH UNIT

3-1/2"

[89mm]

7. Non-combustible material (ie. tile, slate, etc.) may be brought up to the edge of the glass door of the unit. Minimum clearances must be adhered to,

this will assure ease of glass door removal and access to the lower panel.

NOTE: Non-combustible ﬁnishing materials may be of any thickness desired.

Minimum Clearances for Finishing Materials Trim materials

Combustible and Non-combustible Facing and Finishing

Materials around unit.

Note: All non-combustible facing material should butt up cleanly

to the ﬂanges around the ﬁrebox opening.

Rough edges may be visible from an angle.

To maintain a clean ﬁnished edge - facing material edges

may be ﬁnished with a J-style trim or metal cornerbead (both

materials available at your local building or hardware store).

IMPORTANT: Materials used must be NON-COMBUSTIBLE.

CLEAN FINISH

6. If applying a non-combustible facing it may be installed over the metal surface (clean front) of the unit in the area shown below.

Combustible

Material

Non-combustible

Finishing Material

Non-combustible Material (3-1/2" x 34-9/16")

Finishing Material Nailing Strip -flush with unit

Combustible

Material

Non-combustible

Supplied with Unit

1-1/2

(38mm)

Ensure finished

material is

brought to lip

IMPORTANT FINISHING DETAIL NOTE:

Before placing unit into nal position - it is important to know the

total thickness / height of nished hearth (tile, carpet, etc.) The base

of the replace, 4 sided faceplate or mantel should be level or higher

than the nished hearth height.

NOTE: The 3-1/2" x 34-9/16" non combustible material supplied with this unit can be replaced if trying to achieve a clean ﬁnish. A large piece of non

combustible material (ie. 4' x 8' x 1/2") can be used to eliminate taped seams on or near unit.

HZ33CE Gas Fireplace

RIGID PIPE VENTING ARRANGEMENTS

Vertical Terminations

(Propane & Natural Gas)

The shaded area in the diagram shows all allowable combinations of straight vertical and offset to vertical terminations, using one 90o elbow, with

rigid pipe vent systems for Propane and Natural Gas.

•Unit must be raised 1".

• Firestops are required at each oor level and whenever passing through a wall.

• Maintain clearances to combustibles.

• Vent must be supported at o󰀨sets.

Note: Must use optional rigid pipe adapter when using rigid vent systems (Part # 510-994.

HZ33CE Gas Fireplace

12 20

614

30” (762mm) / 26” (660mm) when using flex

Minimum

Height

Requirement

4810 18

Vertical Height (Feet)

Horizontal (Feet)

8"(0.2m)

2 (0.6m)

RIGID PIPE VENTING ARRANGEMENTS

Horizontal Terminations

REGENCY®DIRECT VENT SYSTEM (FLEX)

(Propane & Natural Gas)

This diagram shows all allowable combinations of vertical runs with horizontal terminations, using one 45o and one 90o elbow (two 45o elbows equal one

90o elbow).

Note: Must use optional rigid pipe adaptor (Part # 510-994. when using rigid pipe vent systems. (Refer "Rigid Pipe Venting Systems" Section)

• Maintain clearances to combustibles.

• Horizontal vent must be supported every 3 feet.

• Firestops are required at each oor level and whenever passing through a wall.

A vent guard should be used whenever the

termination is lower than the speciﬁed minimum

or as per local codes.

Note: Regency®Direct Vent System (Flex)

is only approved for horizontal

terminations.

Minimum

Simpson Dura-Vent Center-Line Minimum

Flex Kit Center-Line

This manual suits for next models

Table of contents

Other Regency Indoor Fireplace manuals

Regency

Regency CV40E-NG Quick start guide

Regency

Regency Panorama P121 Quick start guide

Regency

Regency Z2510L Quick start guide

Regency

Regency H2100 Quick start guide

Regency

Regency CC40LE-NG Quick start guide

Regency

Regency Panorama PG33NG4-R Quick start guide

Regency

Regency P33-LP3 Quick start guide

Regency

Regency Wood Insert I2400 User manual

Regency

Regency U31-NG3 Quick start guide

Regency

Regency Liberty LRI4E series Quick start guide

Regency

Regency Liberty L900-1 User manual

Regency

Regency Greenfire GF900C Quick start guide

Regency

Regency L390PB Quick start guide

Regency

Regency P36E-NG10 Quick start guide

Regency

Regency Liberty L900 Gas Fireplace L900-NG1 Quick start guide

Regency

Regency City Series New York 40 User manual

Regency

Regency MANSFIELD L850B ST Quick start guide

Regency

Regency P48-2 Quick start guide

Regency

Regency Ultimate U1500E-LP User manual

Regency

Regency U31-NG10 Quick start guide

Regency

Regency Liberty Gas Fireplace L676-NG1 Quick start guide

Regency

Regency Energy U32-NG10 Quick start guide

Regency

Regency Greenfire GF1500L NG-2 User manual

Regency

Regency Gas Insert E21-NG3 Quick start guide

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual