Regency GFi750 Quick start guide

PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE

REFERENCE

Models: GFi750NG

GFi750LP

GFi750ULPG

Owners &

Installation

Manual

11/23/22

LISTINGS AND CODE APPROVALS

These gas appliances have been tested in

accordance with AS/NZS 5263.0 & AS/NZS

5263.1.3-2021 and have been certied by

IAPMO for installation and operation as de-

scribed in these Installation and Operating

Instructions. Must be installed as per AS/

NZS5601.

Your unit should be serviced annually

by an authorised service person.

920-457

GFi750 GAS INBUILT

FOR YOUR SAFETY

What to do if you smell gas:

Do not try to light any

appliance

Do not touch any electrical

switch: do not use any

phone in your building.

Immediately call your gas

supplierfromaneighbour's

phone. Follow the gas

supplier's instructions.

If you cannot reach your

gas supplier, call the re

department.

WARNING:

Improper installation, adjustment,

alteration, service or maintenance can

cause injury or property damage. Refer to

this manual. For assistance or additional

information consult an authorised installer,

service agency or the gas supplier.

FOR YOUR SAFETY

Do not store or use gasoline or other

ammable vapours and liquids in the

vicinity of this or any other appliance.

Installation and service must be performed

by an authorised installer, service agency

or the gas supplier.

2| Regency GFi750 Gas Inbuilt Fireplace

Regency Gas Inbuilt Fireplace

TO THE NEW OWNER

Congratulations! You are the owner of a state-of-the-art Gas Inbuilt Fireplace by FPI. The Regency Gas

Fireplace Series of appliances has been designed to provide you with all the warmth and charm of a

replace, at the ick of a switch. The model GFi750 of this series has been approved by IAPMO for both

safety and eciency. As it also bears our own mark, it promises to provide you with economy, comfort

and security for many trouble free years to follow. Please take a moment now to acquaint yourself with

these instructions and the many features of your Regency Fireplace.

Regency GFi750 Gas Inbuilt Fireplace | 3

dimensions

Unit Dimensions - Flush Install (millimeters)

276

PROJECTION

REV:PART NO:

TOLERANCES UNLESS

DRAWING

3RD ANGLE

PROCESS :

THIS DRAWING IS THE PROPERTY OF FPI LTD., IT MAY NOT BE COPIED IN WHOLE OR IN PART, OR DISCLOSED TO A THIRD PARTY WITHOUT OUR PRIOR WRITTEN CONSENT.

MAT'L :

DWN:

PART :

UNITS IN INCHES DATE:

DO NOT SCALE

OTHERWISE STATED

E.C.N.: SIGN:

DIMENSIONS

0.000 = 0.01 CRITICAL

0.000 = SPECIFIED TOLERANCE

0.000 = 0.031

0.000 REF = REFERENCE ONLY

ANGULAR =

FIREPLACE PRODUCTS

INTERNATIONAL

346-500

PYUEN

SHEAR/ PUNCH/ FORM

05/06/2020

DATE:

SCALE: 1:10

383

542

676

100

575

741

605

414

584

4| Regency GFi750 Gas Inbuilt Fireplace

dimensions

Unit Dimensions - With Backing Plate (millimeters)

276

TOLERANCES UNLESS

DRAWING

3RD ANGLE

PROCESS :

DWN:

SIGN:

E.C.N.: DATE:

DO NOT SCALE

THIS DRAWING IS THE PROPERTY OF FPI LTD., IT MAY NOT BE COPIED IN WHOLE OR IN PART, OR DISCLOSED TO A THIRD PARTY WITHOUT OUR PRIOR WRITTEN CONSENT.

OTHERWISE STATEDPROJECTION

UNITS IN INCHES

REV:PART NO:

MAT'L :

PART :

DIMENSIONS

0.000 = 0.01 CRITICAL

0.000 = SPECIFIED TOLERANCE

0.000 = 0.031

0.000 REF = REFERENCE ONLY

ANGULAR =

FIREPLACE PRODUCTS

INTERNATIONAL

SHEAR/ PUNCH/ FORM

05/06/2020

DATE:

SCALE:

346-500

PYUEN

1:10

Date Printed: Sept 28/2021

383

542

676

100

575

848

655

Regency GFi750 Gas Inbuilt Fireplace | 5

Unit Dimensions - Flush Install (millimeters).................................... 3

Unit Dimensions - With Backing Plate (millimeters) .......................... 4

Data Badge................................................................................... 6

Important Message ....................................................................... 7

For Your Safety ............................................................................. 7

Materials Required......................................................................... 7

Before You Start............................................................................ 7

Minimum Fireplace Opening ........................................................... 8

Installation Checklist...................................................................... 8

Clearances to Combustibles............................................................ 9

Mantel Clearances ........................................................................ 9

Gas Connection ............................................................................ 9

Flueing ......................................................................................... 9

Flue Liner Installation .................................................................. 10

Gas Pipe Pressure Testing ............................................................ 10

885 S.I.T. Valve Description.......................................................... 10

Installation in Full Masonry Chimney............................................. 11

System Data - GFi750L ................................................................ 12

Aeration Settings......................................................................... 12

Conversion Kit #346-969 from NG to Propane/ULPG Model ............ 13

Glass Panel Installation (Part #346-906) ....................................... 15

Log Set Installation ..................................................................... 16

Primary Glass Guard Installation and Removal............................... 19

Glass Door Installation and Removal............................................. 19

Faceplate Installation and Removal............................................... 20

Backing Plate Installation............................................................. 20

Final Check ................................................................................. 21

Wiring ........................................................................................ 21

Standard Wiring .......................................................................... 21

Lighting Procedure ...................................................................... 22

Copy of Lighting Instruction Plate................................................. 23

Normal Operating Sounds Of Gas Appliances................................. 24

Proame II Remote Control Operating Instructions ........................ 25

Proame II Battery Replacement & Battery Back Up ...................... 29

Maintenance Instructions ............................................................. 30

Log Replacement ........................................................................ 30

Door Glass Replacement .............................................................. 30

Glass Gasket ............................................................................... 30

Fan Removal and Installation Option 1 (Front)............................... 31

Fan Removal and Installation Option 2 (Rear Fan Access)............... 32

Inner Panel Removal and Installation............................................ 33

IFC (Integrated Fireplace Control) Error Codes .............................. 33

Gas Appliance Maintenance.......................................................... 34

Main Assembly ............................................................................ 35

Faceplate Assembly ..................................................................... 37

Owner's Information

Installer's Information

Installation

Maintenance

Parts

Operation

Table of Contents

6| Regency GFi750 Gas Inbuilt Fireplace

data badge

This is a copy of the label that accompanies each Regency GFi750 Gas

Inbuilt replace. We have printed a copy of the contents here for your

review.

DATA BADGE NOTE: Regency units are constantly being improved.

Check the label on the unit and if there is a dierence, the label on the

unit is the correct one.

Part #: 920-473

Colour: Black on Grey

Size: 100%

Nov. 09/21 - created decal

March 11/22 - updated gas consumption and orifice values

Electrical: 240VAC 50Hz 1.0 amp

Serial

Number

920-473

N2134

Regency Gas Fireplace

Gas Type NG PROPANE ULPG

Model GFi750NG GFi750LP GFi750ULPG

Gas Consumption High 26 MJ/h 26 MJ/h 21.5 MJ/h

Gas Consumption Low 16.9 MJ/h 18.1 MJ/h 17.7 MJ/h

Min. Supply Pressure 1.13 kPa 2.75 kPa 2.75 kPa

Manifold Pressure High 0.87 kPa 2.49 kPa 2.49 kPa

Manifold Pressure Low 0.40 kPa 1.59 kPa 1.59 kPa

Injector Size 1 x #42 1 x #55

2.37 mm 1.45 mm 1.32 mm

Model

Approval No. GMK10782 SUITABLE ONLY FOR INDOOR INSTALLATION

571

Western Australia:

Air Group Australia

28 Division St

Welshpool, WA 6106

Eastern Australia:

Fireplace Products

Australia Pty. Ltd.

99 Colemans Road

Dandenong South

Vic. Australia 3175

New Zealand:

Aber Holdings

17 Main Street Place

Te Rapa, HA 3200

To be installed by an authorised person in accordance

with installation instructions provided with the

appliance.

AS/NZS 5263.0 & AS/NZS 5263.1.3

Regency GFi750 Gas Inbuilt Fireplace | 7

requirements

installer's information

Important Message

The Regency Gas Inbuilt must be installed in ac-

cordance with these instructions. Carefully read all

the instructions in this manual rst.

Note: Failure to follow these instructions

could cause a malfunction of the heater

which could result in death, serious

bodily injury, and/or property damage.

Failure to follow these instructions

may also void your re insurance and/

or warranty.

For Your Safety

This appliance requires air for proper combustion.

Always provide adequate combustion and ventila-

tion air. Follow instructions and information in the

current AS/NZS5601 or local codes. Consult the

"authority having jurisdiction" to determine the

need for a permit prior to starting the installation.

Before You Start

Installation is to be carried out ONLY by an

authorised person.

1) The appliance shall be installed in accordance

with the manufacturer's installation instructions,

local gas tting regulations, municipal building

codes, water supply regulations, electrical wiring

regulations, with AS/NZS5601.

2) Installation and repair should be done

ONLY by an authorised person.

3) The appliance should be inspected before use

and at least annually by an authorised service

person. More frequent cleaning may be required

due to excessive lint from carpeting, bedding

material, etc. It is imperative that control

compartments, burners and circulating air

passageways of the appliance be kept clean

and free from excessive lint from carpeting.

4) See general construction and assembly instruc-

tions. This appliance may only be installed in a

ued, non-combustible replace. The appliance

and ue should be enclosed when installed or

passing through a living area, where children

may come in contact with it.

5) Always connect this space heater to a chimney

and ue to the outside of the building envelope.

Never ue to another room. Make sure that the

ue is properly sized and is of adequate height

to provide the proper draft.

6) Inspect the ueing system annually for blockage

and any signs of deterioration.

7) Any safety glass removed for servicing must be

replaced prior to operating the appliance.

8) To prevent injury, do not allow anyone who is

unfamiliar with the operation to use the replace.

9) Only Regency ue kit part # 946-773 can be

used. This ue kit contains all the components

required to safely install this GFi750 gas inbuilt.

Materials Required

A 240 Volt AC power cord is hooked up to the unit.

Plug 3 wire cord into a suitable receptacle. Do not

cut the ground terminal o under any circumstances.

When connected with 240 volts, the appliance

must be electrically grounded in accordance with

local codes.

This unit is polarity sensitive and will not

operate if polarity is incorrect.

WARNING:

Suitable for installation into a

masonry replace only.

NOTE:

TO BE INSTALLED ON A

NON- COMBUSTIBLE FLOOR.

PACKAGING: The unit and its contents are

packaged to prevent damage during trans-

port. After unboxing, remove the card-

board spacers and plastic wrap and recycle

or dispose of them properly. Carefully re-

move the logs from inside the box before

commissioning it; unwrap each log and set

aside. Refer to subsequent instructions on

proper set up and safety check before com-

missioning the unit.

8| Regency GFi750 Gas Inbuilt Fireplace

installer's information

Lintel Depth (mm) Height

(mm)

Width Front

(mm)

Depth

(mm)

Width-Back

(mm)

200 590 685 400 565

400

685

590

565

200

100

Minimum Fireplace Opening

The minimum replace openings for the Regency GFi750 gas space heater are shown below: Installation Checklist

Before installing vent system ensure that the damper

plate is open and secure to prevent the damper plate

from falling down and crushing the liner.

The FPI Gas Inbuilt is installed as listed.

1. Check all clearances to combustibles, (Refer

to sections "Minimum Fireplace Opening and

Clearances to Combustibles)

2. Make the gas connection. (Refer to section "Gas

Connection")

3. Install the 76 mm and 102 mm ue liner to the

sliding connector plate. (Refer to section "Flue

Liner Installation.")

4. Slide the unit half way into the replace.

5. Pull the vent connector plate through the tapered

brackets and fasten to the front plate. Refer to

section "Flue Liner Installation.")

6. Slide the unit fully into the replace.

7. Test gas pressure (Refer to section "Gas Pipe

Pressure Testing"). Check aeration system (Refer

to section "Gas Insert Aeration System").

8. Install standard and optional features. Refer

to the following sections:

a. Log Set

b. Door, Primary Guard & Faceplate

c. Inner Glass Panels (optional)

9. Final check: Before leaving this unit with the

customer, the installer must ensure that the

appliance is ring correctly. This includes:

a) Clocking the appliance to ensure the correct

ring rate.

b) Adjusting the primary air and restrictor set-

tings, if required, to ensure that the ame

does not carbon.

Side View

Top View

Regency GFi750 Gas Inbuilt Fireplace | 9

installation

Flueing

This appliance is designed to be attached to two

co-linear aluminium ex pipes running the full length

of the chimney. The ue length must be a minimum

length of 2.44 m and a maximum of 10.7 m. See

chart for minimum distances from roof. Periodically

check that the vent is unrestricted.

Masonry chimneys may take various contours which

the exible liner will accommodate. However, keep

the exible liner as straight as possible, avoid

unnecessary bending.

The Air Intake pipe must be attached to the inlet

air collar of the adaptor.

Gas Connection

GAS CONNECTION WARNING:

Only persons licensed to work

with gas piping may make the

necessary gas connections

to this appliance.

1) If the appliance is to be installed into an existing

chimney system, thoroughly clean the masonry

replace.

2) The appliance is provided with an opening on

the right hand side of the control compartment.

The 9.5 mm exible gas hose provided needs

to be brought in from behind this opening.

Ensure all gas connections are tight.

3) Locate the center point where the vent will pass

through the chimney above the appliance. Move

the appliance into the exact location where it is

to be installed. Ensure that the Insert is level.

305 mm Mantel

89 mm

Mantel

535 mm

560 mm

to floor

Top

Faceplate

305 152 102

203

254

305

152

406

102

356

203

457

254

Side View

330 mm

508

559

Mantel Clearances

Clearances to Combustibles

Minimum Clearances to Combustibles

From Unit

Sides A 180 mm

Ceiling B 1205 mm

Mantel C 330 mm

Max. Mantle Depth E 305 mm

(see Dia. 2)

Min. Alcove Width F 1220 mm

Max. Alcove Depth G 915 mm

*No hearth required.

Gas

Inlet

WARNING

DO NOT USE AN UNLINED

MASONRY CHIMNEY AS THE

FLUE FOR THIS APPLIANCE.

THE APPLIANCE MUST NOT

CONNECT TO A CHIMNEY

FLUE SERVING A SEPARATE

SOLID FUEL BURNING

APPLIANCE AND MUST BE

TERMINATED TO THE

OUTDOORS.

Note: When installing the ueing, identify the

ues. Mark one exhaust and one intake

as indicated on the top of the unit.

Part # Description

948-305 76mm Flex - 10.7m

948-336 102mm Flex - 10.7m

46DVA-VCH Termination Cap High Wind

46DVA-34CLTA Adaptor & Chimney Plate

Flue Restrictor Settings:

29 mm x 2 (Factory Set)

NOTE: Shut o valve must be installed in an

accessible location.

6Regency IG34 Gas Inbuilt Fireplace

INSTALLATION

Flashing

#46DVA-VCH

#948-305

#948-336

#46DVA-34CLTA

#948-305

946-773 Vertical Flue Kit

The ue kit contains the following:

NOTES

• A non-combustible mantel may be in-

stalled at a lower height if the framing

is made of metal studs covered with a

non-combustible board.

• The non-combustible mantle when

installed at a lower overall height may

not be lower than 152 mm from the

top of the replace opening.

10 | Regency GFi750 Gas Inbuilt Fireplace

installation

Gas Pipe Pressure Testing

During pressure testing of the gas supply piping

system at pressures equal to or less than 3.45

kPa, close the appliance's manual shut-o valve

to isolated it from the gas supply. Disconnect the

piping from the valve at pressures over 3.45 kPa.

The manifold pressure is controlled by a regulator

built into the gas control and should be checked

at the pressure test point.

1. Make sure the unit is in the "OFF" position.

2. Loosen the "IN" and/or "OUT" pressure tap(s),

turning counterclockwise with a 3mm wide at

screwdriver.

885 S.I.T. Valve Description

1) 6 Stage ame adjustment

2) Pilot adjustment

3) Outlet Pressure Tap

4) Inlet Pressure Tap

5) Pilot Outlet

6) Main Gas Outlet

7) Main Gas Inlet

3. Attach manometer to "IN" and/or "OUT" pres-

sure tap(s) using a 8mm ID hose.

4. Turn the unit on with the remote or wall switch.

5. The pressure check should be carried out with

the unit burning and the setting within the limits

specied on the safety label.

NOTE

Screw should be snug, but do not over tighten.

NOTE

• To properly check gas pressure, both inlet

and manifold pressures should be checked

using the valve pressure ports on the valve.

6. When nished reading the manometer, turn o

the unit, disconnect the hose, and tighten the

screw (clockwise) with a 3mm at screwdriver.

This manual suits for next models

Table of contents

Other Regency Indoor Fireplace manuals

Regency

Regency GFI300LNG-R User manual

Regency

Regency Bellavista B36X Quick start guide

Regency

Regency Energy U32-NG10 Quick start guide

Regency

Regency P36-NG4 Quick start guide

Regency

Regency CC40LE-NG Quick start guide

Regency

Regency IG35-NG Quick start guide

Regency

Regency Horizon HZ40E Service manual

Regency

Regency Alterra CI1203 Quick start guide

Regency

Regency IP28-NG Quick start guide

Regency

Regency City Series Quick start guide

Regency

Regency City CV60EPV-NG Quick start guide

Regency

Regency HZI234E-NG Quick start guide

Regency

Regency City CB72EPV-LP Quick start guide

Regency

Regency I100B-1 BERWICK Quick start guide

Regency

Regency IG34 Quick start guide

Regency

Regency City CV50E DIRECT VENT Quick start guide

Regency

Regency Liberty LRI4E series Quick start guide

Regency

Regency I31-LPG3 Quick start guide

Regency

Regency GF900L-NG Quick start guide

Regency

Regency City Series Quick start guide

Regency

Regency L965E-NG Quick start guide

Regency

Regency Gas Fireplace P42-LP4 Quick start guide

Regency

Regency Liberty LRI4E series Quick start guide

Regency

Regency Bellavista B41XTCE-NG10 Quick start guide

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual