Regency Bellerive I200B-1 Quick start guide

Model: I200B-1

Owners &

Installation

PLEASE KEEP THESE INSTRUCTIONS FOR

FUTURE REFERENCE

Manual

Oct-13-2015

918-696e

WARNING:

Improper installation, adjustment, alteration, service or maintenance can

cause injury or property damage. Refer to this manual. For assistance

or additional information consult an authorised installer, service agency

or the distributor.

BELLERIVE FIREPLACE INSERT

FPI - FIREPLACE PRODUCTS AUSTRALIA PTY LTD.

1 CONQUEST WAY HALLAM VICTORIA 3803

2Regency Bellerive Fireplace Insert

Thank-you for purchasing a

REGENCY FIREPLACE PRODUCT.

The pride of workmanship that goes into each of our products will give you years of trouble-free enjoyment. Should you

have any questions about your product that are not covered in this manual, please contact the REGENCY DEALER

in your area.

Keep those REGENCY FIRES burning.

SAFETY NOTE: If this wood re is not properly installed, a house re may result. For your safety, follow the installa-

tion instructions, contact local building, re ofcials, or authority having jurisdiction about restrictions and installation

inspection requirements in your area.

The authority having jurisdiction should be consulted before installation to determine the need to obtain a permit.

ONLY CLEAN APPLIANCE WITH A DAMP CLOTH

(NEVER WHEN UNIT IS HOT)

DO NOT USE ANY ABRASIVE CLEANERS

DO NOT BURN (WILL VOID WARRANTY):

• Treated wood • Tea Tree • Oil Based woods • Coal • Garbage

• Cardboard • Solvents • Colored Paper • Trash

Save these

Instructions

CAUTION: BURN UNTREATED WOOD ONLY. OTHER MATERIALS SUCH AS WOOD PRESER-

VATIVES, METAL FOILS, COAL, PLASTIC, GARBAGE, SULPHUR OR OIL WILL DAMAGE THE

FIRE AND ATMOSPHERE.

"This wood heater is designed to burn natural wood only. Higher efciencies and lower emissions gener-

ally result when burning air dried seasoned hardwoods, as compared to green or freshly cut hardwoods."

Regency Bellerive Fireplace Insert 3

table of

contents

OPERATING INSTRUCTIONS

Operating Instructions .........................................................11

Air Slide Control...................................................................11

First Fire .............................................................................. 11

MAINTENANCE

Creosote..............................................................................12

- Ways to Prevent & Keep Units Free of Creosote.......12

Maintenance........................................................................12

Glass Maintenance..............................................................12

Door Latch Adjustment ........................................................12

Wood Storage......................................................................12

PARTS LIST

Heater Assembly .................................................................13

WARRANTY

Warranty ..............................................................................18

Data Badge ............................................................................4

Unit Dimensions ....................................................................5

INSTALLATION

Before Installing Your Insert ...................................................6

Residential Installation ...........................................................6

Safety Guidelines and Warnings ...........................................7

Flue Speciﬁcations ................................................................7

Wood Insert Speciﬁcations ....................................................7

Brick & Cast Installation .........................................................7

Zero Clearance Dimensions..................................................7

Zero Clearance Box Dimensions...........................................7

Fireplace Clearances .............................................................8

Installation into a Masonry Fireplace .....................................9

Installation into a Factory Built Fireplace ...............................9

Faceplate & Fan Installation ................................................10

4Regency Bellerive Fireplace Insert

SAFETY LABEL

data badge

This is a copy of the label that accompanies each

I200B Fireplace Insert. We have printed a copy of

the contents here for your review.

NOTE: Regency units are constantly being

improved. Check the label on the unit and if

there is a difference, the label on the unit is the

correct one.

Regency Bellerive Fireplace Insert 5

DIMENSIONS

dimensions

6Regency Bellerive Fireplace Insert

installation

1) Please read this entire manual before you

install and use your new wood re. Failure

to follow instructions may result in property

damage, bodily injury or even death. Be

aware that local Codes and Regulations may

override some items in this manual. Check

with your local inspector.

2) THE APPLIANCE AND FLUE-SYSTEM

SHALL BE INSTALLED IN ACCORD-

ANCE WITH AS/NZS 2918:2001 AND

THE APPROPRIATE REQUIREMENTS

OF THE RELEVANT BUILDING CODE OR

CODES.

APPLIANCES INSTALLED IN ACCORD-

ANCE WITH THIS STANDARD SHALL

COMPLY WITH THE REQUIREMENTS OF

AS/NZS 4013 WHERE REQUIRED BY THE

REGULATORY AUTHORITY.

ANY MODIFICATION OF THE APPLIANCE

THAT HAS NOT BEEN APPROVED IN

WRITING BY THE TESTING AUTHORITY

IS CONSIDERED TO BE IN BREACH OF

THEAPPROVAL GRANTED FOR COMPLI-

ANCE WITH AS/NZS 4013.

RESIDENTIAL

INSTALLATION

Regency Inserts are constructed with the high-

est quality materials and assembled under strict

quality control procedures that insure years of

trouble free and reliable performance.

It is important that you read this manual thor-

oughly and fully understand the safe instal-

lation and operating procedures. The more

you understand the way your Regency Insert

operates, the more enjoyment you will experi-

ence from knowing that your unit is operating

at peak performance.

BEFORE INSTALLING

YOUR INSERT

1) Please read this entire manual before you

install and use your new wood insert. Failure

to follow instructions may result in property

damage, bodily injury or even death. Install

and use only in accordance with manufactur-

er’s installation and operating instructions.

2) Check your local building codes - Building

Inspection Department. You may require

a permit before installing your insert. Be

aware that local codes and regulations may

override some items in the manual.

WARNING: Careless installation is the

major cause of safety hazard. Check all

local building and safety codes before

installation of unit.

3) Notify your home insurance company that

you plan to install a replace insert or hearth

heater.

4) Your replace insert is heavy and requires

two or more people to move it safely. The

insert can be badly damaged by mishan-

dling.

5) If your existing replace damper control

will become inaccessible once you have

installed your Regency Insert, you should

either remove or secure it in the open posi-

tion.

6) Inspect your replace and ue prior to install-

ing your insert to determine that it is free

from cracks, loose mortar or other signs of

damage. If repairs are required, they should

be completed before installing your insert.

Do not remove bricks or mortar from your

masonry replace.

7) Do not connect the insert to a ue system

servicing another appliance or an air

distribution duct.

CAUTION: MIXING OF APPLIANCE OR

FLUE-SYSTEM COMPONENTS FROM

DIFFERENT SOURCES OR MODIFYING

THE DIMENSIONAL SPECIFICATION OF

COMPONENTS MAY RESULT IN HAZ-

ARDOUS CONDITIONS. WHERE SUCH

ACTION IS CONSIDERED, THE MANU-

FACTURER SHOULD BE CONSULTED

IN THE FIRST INSTANCE.

3) Re-conrm the clearance from the insert to

combustibles to insure that they are within

the prescribed limits.

4) Install ue according to ue manufacturers

instructions. The performance of your wood

re is governed to a very large part by the

ue system. Too short a ue can cause

difcult start-up, dirty glass, backsmoking

when door is open, and even reduced heat

output. Too tall a ue may prompt excessive

draft which can result in very short burn times

and excessive heat output.

5) The oor protector must be of non-combus-

tible material.

6) Do not connect this unit to a ue serving

another appliance.

Regency Bellerive Fireplace Insert 7

installation

BRICK & CAST

INSTALLATION

Insert the rear cast plate rst and then the side

plates ensuring the cut out sections lock in rmly.

The bricks can then be placed on the base of the

rebox between the cast side and rear plates.

Firebrick is included to extend the life of your

heater and radiate heat more evenly.

SAFETY GUIDELINES AND

WARNINGS

1) Never use petrol, petrol type lantern fuels,

kerosene, charcoal lighter fuel, or similar

liquids to start or ‘freshen up’ a re in your

heater. Keep all such liquids well away from

the heater while it is in use.

2) Keep the door closed during operation and

maintain all seals in good condition.

3) Do not burn any quantities of paper, garbage,

and never burn ammable uids such as

petrol, naptha or engine oil in your heater.

4) If you have smoke detectors, prevent smoke

spillage as this may set off a false alarm.

5) Do not overre heater. If the ue connector,

ue bafe or the heater top begin to glow,

you are overring. Stop adding fuel and

close the draft control. Overring can cause

extensive damage to your heater including

warpage and premature steel corrosion.

Overring will void your warranty.

6) Do not permit creosote or soot build-up in

the ue system. Check and clean ue at

regular intervals. Failure to do so can result

in a serious ue re.

7) Your Regency heater can be very hot. You

may be seriously burned if you touch the

heater while it is operating, keep children,

clothing and furniture away. Warn children

of the burn hazard. For safety reasons a

guard around the re is recommended.

8) The heater consumes air while operating,

provide adequate ventilation with an air duct

or open a window while the heater is in use.

9) Do not use grates or andirons or other

methods for supporting fuel. Burn directly

on the base or bricks where supplied.

10) Open the draft control fully for 10 to 15

seconds prior to slowly opening the door

when refuelling the re.

11) Do not connect your unit to any air distribu-

tion duct.

12) Your wood re should burn dry, standard

rewood only. The use of cut timber, ply-

wood, “mill ends”, etc. is not allowed as this

fuel can easily overheat your wood re.

Evidence of excessive overheating will void

your warranty. As well, a large portion of

sawmill waste is chemically treated timber,

which is illegal to burn in many areas. Salt

drift wood and chemically treated re logs

also must not be burned in your wood re.

13) DO NOT OPERATE WITH BROKEN

GLASS.

FLUE

SPECIFICATIONS

Before installing, check and clean your ue

system thoroughly. If in doubt about its condition,

seek professional advice. Your Regency Insert is

designed for installation into a masonry replace.

The appliance, when installed, must be electrical-

ly grounded in accordance with local codes.

Height 597mm

Width 699mm

Depth 468mm

WOOD INSERT

SPECIFICATIONS

Your replace opening requires the following

minimum sizes:

GLASS INSTALLATION

Remove the door from the heater and remove

the glass retainer. Position the glass in the door,

make sure that the glass gasketing will properly

seal your unit, and replace the retainer, it should

rest on the gasket not the glass. Tighten securely,

but do not wrench down on the glass as this

may cause the glass to break.

8Regency Bellerive Fireplace Insert

installation

ZERO CLEARANCE

BOX DIMENSIONS

ZERO CLEARANCE

DIMENSIONS

Important: Non-combustible sheeting of a minimum thickness of 12mm must be used on the front face of the enclosure.

Regency Bellerive Fireplace Insert 9

installation

FIREPLACE CLEARANCES

10 Regency Bellerive Fireplace Insert

installation

INSTALLATION INTO A

MASONRY FIREPLACE

The insert must be installed as per the require-

ments of your local inspection authority.

Regency highly recommends the use of a full

liner as the safest installation and provides the

most optimum performance. Your retailer should

be able to help you decide which system would

be the best for your application.

Full Flue Liner

The use of this connection method not only

increases the safety of your insert by directing

the hot gases up the ue, but will also help

increase the unit's efciency and decrease

creosote deposits in the ue.

When a connected ue or liner is in use, the

insert is able to “breathe” better by allowing a

greater draft to be created. The greater draft can

decrease problems such as, difcult start-ups,

smoking out the door, and dirty glass.

INSTALLATION INTO A

FACTORY BUILT

FIREPLACE

1) When installed in a factory built replace, a

full stainless steel rigid is mandatory, for both

safety and performance purposes. When

a ue or liner is in use, the insert is able to

breathe better by allowing a greater draft to

be created. The greater draft can decrease

problems such as, difcult start-ups, smoking

out the door, and dirty glass.

2) In order to position the ue liner, the exist-

ing rain cap must be removed from your

ue system. In most cases the ue damper

should also be removed to allow passage

of the liner.

3) In most cases opening the existing spark

screens fully should give enough room for

the insert installation. If it does not, remove

and store.

4) If the oor of your replace is below the

level of the replace opening, adjust the

insert's levelling bolts to accommodate the

difference. When additional shimming is

required, use non-combustible masonry or

steel shims.

5) Measure approximately the alignment of

the ue liner with the position of the smoke

outlet hole on the insert to check for possible

offset. If an offset is required, use a proper

stainless steel unit available with the ue

liner.

6) Once the above items have been checked,

slide your insert into position after rst po-

sitioning the ue liner and offset if required.

(Re-install raincap at completion of installa-

tion).

Other manuals for Bellerive I200B-1

Table of contents

Other Regency Indoor Fireplace manuals

Regency

Regency Panorama PG121NG1-R Quick start guide

Regency

Regency Liberty Gas Fireplace L676-NG1 Quick start guide

Regency

Regency City Series Quick start guide

Regency

Regency B41XTCE-NG11 User manual

Regency

Regency Hampton HI2450 Quick start guide

Regency

Regency City CB60E-1 Quick start guide

Regency

Regency liberty LRI6E Quick start guide

Regency

Regency I1200 Quick start guide

Regency

Regency P121-NG Quick start guide

Regency

Regency F5102 - AUSTRALIA Quick start guide

Regency

Regency Alterra CI1203 Quick start guide

Regency

Regency U31-NG and User manual

Regency

Regency Greenfire GF1500L-NG Quick start guide

Regency

Regency I1203S Quick start guide

Regency

Regency H2105 Service manual

Regency

Regency Bellavista B36XTE Quick start guide

Regency

Regency I35-NG Quick start guide

Regency

Regency Ei25 User manual

Regency

Regency Grandview G800EC Series User manual

Regency

Regency PG36NG5-R Quick start guide

Regency

Regency HZI234E-NG Quick start guide

Regency

Regency L540PB Service manual

Regency

Regency B41XTE-NG10 Quick start guide

Regency

Regency Z2510L Quick start guide

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual