Regency Fireplace Products MONTROSE Quick start guide

Model: L850B-1

Owners &

Installation

PLEASE KEEP THESE INSTRUCTIONS FOR

FUTURE REFERENCE

Manual

March-01-2021

920-372

WARNING:

Improper installation, adjustment, alteration, service or maintenance can

cause injury or property damage. Refer to this manual. For assistance or

additional information consult an authorised installer, service agency or

the distributor.

It is highly recommended for protection of infants and inﬁrm to place a

secure safety guard in front of this appliance when in operation.

MONTROSE WOOD FIREPLACE

FPI - FIREPLACE PRODUCTS AUSTRALIA PTY LTD.

1-3 CONQUEST WAY HALLAM VICTORIA 3803

2Montrose Woodﬁre

Thank you for purchasing a

REGENCY FIREPLACE PRODUCT

The pride of workmanship that goes into each of our products will give you years of trouble-free

enjoyment. Should you have any questions about your product that are not covered in this manual,

please contact the REGENCY DEALER in your area.

Keep those REGENCY FIRES burning.

SAFETY NOTE: If this wood ﬁre is not properly installed, a house ﬁre may result. For your safety,

follow the installation instructions, contact local building, ﬁre ofﬁcials, or authority having jurisdiction

about restrictions and installation inspection requirements in your area.

The authority having jurisdiction should be consulted before installation to determine the need to

obtain a permit.

CAUTION: BURN UNTREATED WOOD ONLY. OTHER MATERIALS SUCH AS WOOD PRESER-

VATIVES, METAL FOILS, COAL, PLASTIC, GARBAGE, SULPHUR OR OIL WILL DAMAGE THE

FIRE AND ATMOSPHERE.

"This wood heater is designed to burn natural wood only. Higher efﬁciencies and lower emissions

generally result when burning air dried seasoned hardwoods, as compared to green or freshly

cut hardwoods."

ONLY CLEAN APPLIANCE WITH A DAMP CLOTH

(NEVER WHEN UNIT IS HOT)

DO NOT USE ANY ABRASIVE CLEANERS

DO NOT BURN (WILL VOID WARRANTY):

• Treated wood • Tea Tree • Oil Based woods • Coal • Garbage

• Cardboard • Solvents • Colored Paper • Trash

Montrose Woodﬁre 3

table of

contents

Compliance Plate ..................................................................4

Unit Dimensions ....................................................................5

INSTALLATION

Before Installing Your Fireplace .............................................6

Safety Guidelines and Warnings ...........................................7

Wood Fireplace Speciﬁcations ..............................................8

Wood Fireplace Speciﬁcs-Minimum Clearances ...................9

Optional Base Frame ...........................................................10

Flue and Flue Requirements ...............................................11

Installation Instructions ........................................................15

Optional Fan Kit Installation

Listing and Code Approvals..........................................18

General Information ......................................................18

Minimum Framing Clearances ......................................18

Fan Kit Installation ........................................................19

Fan Duct Extension Kit .................................................20

Wiring Diagram .............................................................20

Optional Outside Air Kit Installation .....................................21

Brick Installation ..................................................................22

APPLIANCE MAINTENANCE

Creosote ..............................................................................23

Ash Removal .......................................................................23

Glass Installation .................................................................23

Glass Maintenance ..............................................................23

Door Latch Adjustment ........................................................23

Trouble Shooting ..................................................................24

OPERATING INSTRUCTIONS

Additional Warnings ......................................................25

Air Slide Control ...........................................................25

Fuel Requirements .......................................................25

Lighting the Appliance ..................................................26

PARTS LIST

Main Assembly ....................................................................27

WARRANTY

Installation of Appliance Checklist.......................................29

Warranty ..............................................................................30

4Montrose Woodﬁre

compliance plate

This is a copy of the data badge that accompanies

each L850B Fireplace. We have included a copy of

the contents here for your review.

NOTE: Regency units are constantly being

improved. Check the data badge on the unit

and if there is a difference, the data badge on

the unit is the correct one.

COPY OF DATA BADGE

PLEASE MAKE NOTE OF THE UNIT SERIAL NUMBER AND ENTER IN THE SPACE PROVIDED

Part #: 920-373

Colour: Black on Grey

Size: 100%

Jan. 01/11: Created Draft

Model: MONTROSE L850B-1

JAN FEB MAR APR MAY JUN JUL AUG SEP OCT NOV DEC 2021 2022 2023 2024 2025

TESTED BY:

HRL TECHNOLOGY PTY LTD.

TRAMWAY ROAD MORWELL VICTORIA 3840 (2014)

MAXIMUM AVERAGE HEAT OUTPUT BURNING HARDWOOD: 11kW

OVERALL AVERAGE EFFICIENCY BURNING HARDWOOD: 62%

Date of Manufacture:

Serial

Number

920-373

557

WHEN TESTED IN ACCORDANCE WITH AS/NZS 4012:2014 & AS/NZS 4013:2014

PARTICULATE EMISSION FACTOR: 1.2 g/kg

CATALYTIC COMBUSTOR: NO

TEST REPORT NUMBER: HCMG/14/023A

MAKE: REGENCY

TYPE: FIREPLACE INSERT

MANUFACTURER/DISTRIBUTOR: FIREPLACE PRODUCTS AUSTRALIA PTY. LTD.

1 CONQUEST WAY, HALLAM VIC 3803

Montrose Woodﬁre 5

dimensions

UNIT DIMENSIONS

1. Reduced Clearance Box Dimensions

2. Standard Firebox Front Dimensions

FPI(China) LTD.

Canature

開能

上海开能壁炉产品有限公司

1066

930

790

310

444

614

550

487

449

412

153

275

986

1011

批准

审核

设计

日期

日期王从坦

标记更改描述签名日期

2021/2/1

材料:

规格:

F1560401-1

第1页/共1页

数量:1

比例:1:20

仅用于实验室图纸

0～30mm ±0.2mm；

＞30～100mm ±0.5mm；

＞100～500mm ±1.0mm；

＞500～1000mm±2.0mm；

＞1000mm ±5.0mm；

ALL HOLES ±0.2mm。

未注公差:ISO2768mK

图框:A4 未注光洁度Rz63

锐角倒钝，去除毛刺，

未注尺寸参考3D造型

投影标记:

必检尺寸:

D:\壁炉内部共享\1-壁炉产品\01-FPA\P10-L850B燃木壁炉（F1560401）\01-模型图纸\

共用项目数量

表面处理:

Montrose(L850B)嵌入式燃

木壁炉(出口）P10-加高型

P10 L850B

FPI(China) LTD.

Canature

開能

上海开能壁炉产品有限公司

1066

930

790

310

444

614

550

487

449

412

153

275

986

1011

批准

审核

设计

日期

日期王从坦

标记更改描述签名日期

2021/2/1

材料:

规格:

F1560401-1

第1页/共1页

数量:1

比例:1:20

仅用于实验室图纸

0～30mm ±0.2mm；

＞30～100mm ±0.5mm；

＞100～500mm ±1.0mm；

＞500～1000mm±2.0mm；

＞1000mm ±5.0mm；

ALL HOLES ±0.2mm。

未注公差:ISO2768mK

图框:A4 未注光洁度Rz63

锐角倒钝，去除毛刺，

未注尺寸参考3D造型

投影标记:

必检尺寸:

D:\壁炉内部共享\1-壁炉产品\01-FPA\P10-L850B燃木壁炉（F1560401）\01-模型图纸\

共用项目数量

表面处理:

Montrose(L850B)嵌入式燃

木壁炉(出口）P10-加高型

P10 L850B

FPI(China) LTD.

Canature

開能

上海开能壁炉产品有限公司

1066

930

790

310

444

614

550

487

449

412

153

275

986

1011

批准

审核

设计

日期

日期王从坦

标记更改描述签名日期

2021/2/1

材料:

规格:

F1560401-1

第1页/共1页

数量:1

比例:1:20

仅用于实验室图纸

0～30mm ±0.2mm；

＞30～100mm ±0.5mm；

＞100～500mm ±1.0mm；

＞500～1000mm±2.0mm；

＞1000mm ±5.0mm；

ALL HOLES ±0.2mm。

未注公差:ISO2768mK

图框:A4 未注光洁度Rz63

锐角倒钝，去除毛刺，

未注尺寸参考3D造型

投影标记:

必检尺寸:

D:\壁炉内部共享\1-壁炉产品\01-FPA\P10-L850B燃木壁炉（F1560401）\01-模型图纸\

共用项目数量

表面处理:

Montrose(L850B)嵌入式燃

木壁炉(出口）P10-加高型

P10 L850B

FPI(China) LTD.

Canature

開能

上海开能壁炉产品有限公司

1097

1069

999

571

901

448

203

173

批准

审核

设计

日期

日期王从坦

标记更改描述签名日期

2021/2/1

材料:

规格:

F1560200A

第1页/共1页

数量:1

比例:1:10

仅用于实验室图纸

0～30mm ±0.2mm；

＞30～100mm ±0.5mm；

＞100～500mm ±1.0mm；

＞500～1000mm±2.0mm；

＞1000mm ±5.0mm；

ALL HOLES ±0.2mm。

未注公差:ISO2768mK

图框:A4 未注光洁度Rz63

锐角倒钝，去除毛刺，

未注尺寸参考3D造型

投影标记:

必检尺寸:

D:\壁炉内部共享\1-壁炉产品\01-FPA\P10-L850B燃木壁炉（F1560401）\01-模型图纸\

共用项目数量

表面处理:

ZC外壳装配组件-加高型

P10 L850B Montrose

FPI(China) LTD.

Canature

開能

上海开能壁炉产品有限公司

1097

1069

999

571

901

448

203

173

批准

审核

设计

日期

日期王从坦

标记更改描述签名日期

2021/2/1

材料:

规格:

F1560200A

第1页/共1页

数量:1

比例:1:10

仅用于实验室图纸

0～30mm ±0.2mm；

＞30～100mm ±0.5mm；

＞100～500mm ±1.0mm；

＞500～1000mm±2.0mm；

＞1000mm ±5.0mm；

ALL HOLES ±0.2mm。

未注公差:ISO2768mK

图框:A4 未注光洁度Rz63

锐角倒钝，去除毛刺，

未注尺寸参考3D造型

投影标记:

必检尺寸:

D:\壁炉内部共享\1-壁炉产品\01-FPA\P10-L850B燃木壁炉（F1560401）\01-模型图纸\

共用项目数量

表面处理:

ZC外壳装配组件-加高型

P10 L850B Montrose

FPI(China) LTD.

Canature

開能

上海开能壁炉产品有限公司

1097

1069

999

571

901

448

203

173

批准

审核

设计

日期

日期王从坦

标记更改描述签名日期

2021/2/1

材料:

规格:

F1560200A

第1页/共1页

数量:1

比例:1:10

仅用于实验室图纸

0～30mm ±0.2mm；

＞30～100mm ±0.5mm；

＞100～500mm ±1.0mm；

＞500～1000mm±2.0mm；

＞1000mm ±5.0mm；

ALL HOLES ±0.2mm。

未注公差:ISO2768mK

图框:A4 未注光洁度Rz63

锐角倒钝，去除毛刺，

未注尺寸参考3D造型

投影标记:

必检尺寸:

D:\壁炉内部共享\1-壁炉产品\01-FPA\P10-L850B燃木壁炉（F1560401）\01-模型图纸\

共用项目数量

表面处理:

ZC外壳装配组件-加高型

P10 L850B Montrose

6Montrose Woodﬁre

installation

BEFORE INSTALLING YOUR FIREPLACE

1) Please read this entire manual before you install and use your new wood ﬁreplace. Failure to follow instructions may result in property damage,

bodily injury or even death. Install and use only in accordance with manufacturer’s installation and operating instructions.

2) Check your local building codes - Building Inspection Department. You may require a permit before installing your ﬁreplace. Be aware that local codes and

regulations may override some items in the manual.

3) Notify your home insurance company that you plan to install a ﬁreplace insert or freestanding heater.

4) THE FIREPLACE CAN GET VERY HOT. DO NOT INSTALL, PLACE OR POSITION TV’S, PAINTINGS, PICTURES, CANDLES, FURNITURE, DRAPES

OR ANY OTHER COMBUSTIBLE ITEMS ON THE WALL OR NEAR THE FIREPLACE.

5) ENSURE THERE ARE NO EXHAUST FANS WITHIN THE VICINITY OF THE FIREPLACE AS THIS CAN CAUSE THE FIREPLACE TO EMIT FUMES

BACK INTO THE ROOM.

6) ENSURE THERE IS ADEQUATE AIR SUPPLY WITHIN THE ROOM/AREA THE FIREPLACE IS BEING INSTALLED IN TO ENSURE PROPER OPERA-

TION OF THE FIREPLACE. INSTALL OPTIONAL OUTSIDE AIR KIT IF IN DOUBT.

7) EVALUATE THE LOCATION OF YOUR FIREPLACE AND OPTIONAL COMPONENTS. IT IS VERY IMPORTANT TO DETERMINE HOW THE FIREPLACE

IS GOING TO BE FINISHED. THE FEATURES YOU WOULD LIKE TO INCORPORATE SUCH AS THE OUTSIDE AIR KIT AND EXTERNAL FAN KITS

NEED TO BE EVALUATED PRIOR TO INSTALLATION.

8) DETERMINE WHAT THICKNESS OF YOUR DESIRED NON-COMBUSTIBLE FINISHING MATERIALS WILL BE INCLUDING THE HEAT RESISTANT

NON-COMBUSTIBLE BOARD. THIS PRE-DETERMINED THICKNESS WILL DICTATE THE POSITION OF THE SUPPORT FLANGES, FRAMING AND

OVERALL FINAL LOOK OF YOUR FIREPLACE.

9) Your ﬁreplace is heavy and requires two or more people to move it safely. The ﬁreplace can be badly damaged by mishandling and or injury can occur.

10) Do not connect the ﬁreplace to a ﬂue system servicing another appliance or an air distribution duct.

WARNING: CARELESS INSTALLATION IS THE MAJOR CAUSE OF SAFETY HAZARD. CHECK ALL LOCAL BUILDING AND SAFETY CODES BEFORE

INSTALLATION OF UNIT.

THE APPLIANCE, WHEN INSTALLED, MUST BE ELECTRICALLY GROUNDED IN ACCORDANCE WITH LOCAL CODES.

Regency Fireplaces are constructed with the highest quality materials and assembled under strict quality control procedures that ensure years of trouble free

and reliable performance.

It is important that you read this manual thoroughly and fully understand the safe installation and operating procedures. The more you understand the way

your Regency Fireplace operates, the more enjoyment you will experience from knowing that your unit is operating at peak performance.

Montrose Woodﬁre 7

installation

1) Never use petrol, petrol type lantern fuels, kerosene, charcoal lighter

fuel, or similar liquids to start or ‘freshen up’ a ﬁre in your heater. Keep

all such liquids well away from the heater while it is in use.

2) Keep the door closed during operation and maintain all seals in

good condition.

3) Do not burn any quantities of paper, garbage, and never burn ﬂam-

mable ﬂuids such as petrol, naptha or engine oil in your heater.

4) If you have smoke detectors, prevent smoke spillage as this may

set off a false alarm.

5) Do not overﬁre heater. If the ﬂue connector, ﬂue bafﬂe or the heater

top begin to glow, you are overﬁring. Stop adding fuel and close the

draft control. Overﬁring can cause extensive damage to your heater

including warpage and premature steel corrosion. Overﬁring will void

your warranty.

6) Do not permit creosote or soot build-up in the ﬂue system. Check

and clean ﬂue at regular intervals. Failure to do so can result in a seri-

ous ﬂue ﬁre.

7) Your Regency heater can be very hot. You may be seriously burned

if you touch the heater while it is operating, keep children, clothing and

furniture away. Warn children of the burn hazard. For safety reasons

a guard around the ﬁre is recommended.

8) The heater consumes air while operating, provide adequate ventila-

tion with an air duct or open a window while the heater is in use or use

optional outside air kit.

9) Do not use grates or andirons or other methods for supporting fuel.

Burn directly on the base or bricks where supplied.

10) Open the draft control fully for 10 to 15 seconds prior to slowly

opening the door when refuelling the ﬁre.

11) Do not connect your unit to any air distribution duct.

12) Your wood ﬁre should burn dry, standard ﬁrewood only. The use of

cut timber, plywood, “mill ends”, etc. is not allowed as this fuel can easily

overheat your wood ﬁre. Evidence of excessive overheating will void

your warranty. As well, a large portion of sawmill waste is chemically

treated timber, which is illegal to burn in many areas. Salt drift wood

and chemically treated ﬁre logs also must not be burned in your wood

ﬁre.

13) DO NOT OPERATE WITH BROKEN GLASS.

WARNING: THE APPLIANCE AND FLUE-SYSTEM SHALL BE

INSTALLED IN ACCORDANCE WITH AS/NZS 2918 AND THE

APPROPRIATE REQUIREMENTS OF THE RELEVANT BUILDING

CODE OR CODES.

WARNING: APPLIANCES INSTALLED IN ACCORDANCE WITH THIS

STANDARD SHALL COMPLY WITH THE REQUIREMENTS OF AS/

NZS 4013 WHERE REQUIRED BY THE REGULATORY AUTHORITY.

I.E. THE APPLIANCE SHALL BE IDENTIFIABLE BY A COMPLIANCE

PLATE WITH THE MARKING 'TESTED TO AS/NZS 4013'.

ANY MODIFICATION OF THE APPLIANCE THAT HAS NOT BEEN

APPROVED IN WRITING BY THE TESTING AUTHORITY IS CON-

SIDERED TO BE IN BREACH OF THE APPROVAL GRANTED FOR

COMPLIANCE WITH AS/NZS 4013.

CAUTION: MIXING OF APPLIANCE OR FLUE-SYSTEM COM-

PONENTS FROM DIFFERENT SOURCES OR MODIFYING THE

DIMENSIONAL SPECIFICATION OF COMPONENTS MAY RESULT

IN HAZARDOUS CONDITIONS. WHERE SUCH ACTION IS CON-

SIDERED, THE MANUFACTURER SHOULD BE CONSULTED IN

THE FIRST INSTANCE.

CAUTION: CRACKED AND BROKEN COMPONENTS, e.g. GLASS

PANELS OR CERAMIC TILES MAY RENDER THE INSTALLATION

UNSAFE.

WARNING: ANY MODIFICATION OF THE APPLIANCE THAT HAS

NOT BEEN APPROVED IN WRITING BY THE TESTING AUTHORITY

IS CONSIDERED AS BREACHING AS/NZS 4013.

WARNING: DO NOT USE FLAMMABLE LIQUIDS OR AEROSOLS

TO START OR REKINDLE THE FIRE.

WARNING DO NOT USE FLAMMABLE LIQUIDS OR AEROSOLS

IN THE VICINITY OF THIS APPLIANCE WHEN IT IS OPERATING.

WARNING: DO NOT STORE FUEL WITHIN HEATER INSTALLA-

TION CLEARANCES.

WARNING: DO NOT USE AS AN OPEN FIRE OR OPERATE WITH

THE DOOR OPEN.

WARNING: OPEN AIR CONTROL (AND DAMPER WHEN FITTED)

BEFORE OPENING FIRE DOOR.

CAUTION: THIS APPLIANCE SHOULD NOT BE OPERATED WITH

A CRACKED GLASS.

CAUTION: THIS APPLIANCE SHOULD BE MAINTAINED AND

OPERATED AT ALL TIMES IN ACCORDANCE WITH THESE IN-

STRUCTIONS

SAFETY GUIDELINES AND WARNINGS/CAUTIONS

CAUTION: THE USE OF SOME TYPES PRESERVATIVE-TREATED

WOOD AS A FUEL CAN BE HAZARDOUS

8Montrose Woodﬁre

installation

UNIT DIMENSIONS

Dimensions

The outside dimensions of the Montrose L850 including the Reduced

Clearance Box is as follows:

• Width 1097mm

•

• Depth = 448mm

•

• Height = 801mm

Height of optional Base Framing Kit = 300mm

Note: Base is non-combustible and needs assembly

COMBUSTIBLE CAVITY REQUIREMENTS

Cavity Depth = Minimum 548mm - 720mm

Note: Cavity depth is determined by the position of support strips and

thickness of non-combustible wall ﬁnish. Rear clearance must be a

minimum of 100mm to combustibles.

CAVITY WIDTH = 1497MM TO COMBUSTIBLES.

Height of reduced clearance box off the ground should be a minimum of

300mm and supported by a non-combustible stand able to support 265kg.

CAVITY HEIGHT: Timber framing in the ceiling cavity must be a minimum

of 1200mm above the reduced clearance box.

Flue

• Minimum 4.5 Meters of triple

skin ﬂue required with approved

cowling. Regency approved ﬂue

kit to be used.

Optional Ducting

• One or two optional fan forced

ducting kits are available, using

150mm ducting to a max run of

9 meters

Clearance Dimensions

Montrose Woodﬁre 9

installation

WOOD FIREPLACE SPECIFICS AND MINIMUM CLEARANCES TO COMBUSTIBLES

Enclosure Ventilation

Unit cavity to have a minimum of two 20,000mm2 air vents must be

installed, one 300mm from the top of the enclosure and one 50mm

from the bottom of the enclosure to stop excessive heat built up

in the enclosure.

Wall Materials

Non-combustible material with a minimum thickness of 9mm must

be used on the front wall of the reduced enclosure. Non combustible

board and non combustible cladding to ﬁnish up to the standoff

brackets. Must maintain 20mm gap around entire face of the unit.

Please note: Non-combustible materials need to be ﬁt for purpose

as wall temperatures can exceed 250o.

Hearth / Floor Protection Requirements

Hearth needs to be 6mm thick, 1475mm wide and 1,100mm deep to allow for 550mm leading

edge. We do recommend that your non-combustible hearth extends 900mm in front of the

unit. This allows the ﬂoor to be protected when the door is fully open in case of ember drop.

The appliance must be installed on a non-combustible stand 300mm above the hearth.

Cavity

Timber framing in the ceiling cavity must be a minimum of 1200mm above the zero box.

200 mm TO TIMBER STUD SIDEWALL

ONLY

1200mm

100mm

MUST USE NON-COMBUSTIBLE MA-

TERIALS 315MM ABOVE THE UNITS

OUTER SHELL(REDUCED CLEAR-

ANCE BOX), 200MM FROM THE

SIDES OF THE OUTER SHELL AND

ALL BELOW THE HEATER.

MAX. ALCOVE

Vent

50mm

(height of vent)

300mm min

(Height of

vent)

1497mm

550mm

548mm

6mm THICK CEMENT FIBRE

FREE SHEET AS HEARTH

(1475mm x 1100mm)

Hearth extends under unit base

1475mm

Clearance to combustibles

Note: Venting in the ceiling of the enclosure around

the outer triple ﬂue skin must be a minimum of

25mm clearance evenly spaced around the outer

casing.

CLEARANCE TO COMBUSTIBLES

Timber Stud

Min. 200mm

to Timber

Stud

Min. 200mm

to Timber

Stud

Min. 300mm to

Timber Stud

Vent

10 Montrose Woodﬁre

installation

OPTIONAL BASE FRAME

CONSTRUCTING YOUR OWN BASE FRAME

WHEN BUILDING YOUR OWN BASE FRAME OR PEDESTAL BASE PLEASE

ENSURE THE FOLLOWING CONDITIONS ARE MET:

1. MINIMUM HEIGHT OF THE BASE FRAME IS 300MM FROM THE FLOOR PROTECTOR / HEARTH TO THE UNDERSIDE OF THE REDUCED CLEAR-

ANCE BOX. IF BASE FRAME DOES NOT SIT ON THE SAME LEVEL OF THE FINISHED FLOOR, THEN THE FRAME NEEDS TO BE MADE TALLER

TO ENSURE THE 300MM CLEARANCE IS MET. (SEE PAGE 10).

2. ENSURE THE BASE IS HOLLOW REGARDLESS OF USING OPTIONAL OUTSIDE AIR KIT OR NOT.

3. ENSURE THE BASE IS CONSTRUCTED OF NON-COMBUSTIBLE MATERIALS

4. ENSURE THE BASE CAN WITHSTAND THE WEIGHT OF AT LEAST 265KG PLUS.

5. ENSURE THE FLOOR BENEATH THE BASE CAN WITHSTAND AT LEAST 265KG PLUS.

This manual suits for next models

Table of contents

Other Regency Fireplace Products Indoor Fireplace manuals

Regency Fireplace Products

Regency Fireplace Products Horizon HZ33CE-NG10 Quick start guide

Regency Fireplace Products

Regency Fireplace Products I2403M Quick start guide

Regency Fireplace Products

Regency Fireplace Products Skope E110-2 Operating manual

Regency Fireplace Products

Regency Fireplace Products Horizon HZ40E-NG10 Service manual

Regency Fireplace Products

Regency Fireplace Products Grandview G600C-1 Quick start guide

Regency Fireplace Products

Regency Fireplace Products I31-NG3 Service manual

Regency Fireplace Products

Regency Fireplace Products City Series Quick start guide

Regency Fireplace Products

Regency Fireplace Products Pro CI2700 Quick start guide

Regency Fireplace Products

Regency Fireplace Products Gi29L-NG Quick start guide

Regency Fireplace Products

Regency Fireplace Products Grandview G800EH Quick start guide

Regency Fireplace Products

Regency Fireplace Products Bellavista B36XTCE-10 Quick start guide

Regency Fireplace Products

Regency Fireplace Products Grandview G800C-1 Quick start guide

Regency Fireplace Products

Regency Fireplace Products Regency Horizon HZ40E-NG2 Quick start guide

Regency Fireplace Products

Regency Fireplace Products Grandview G800C Quick start guide

Regency Fireplace Products

Regency Fireplace Products Classic I2450M Quick start guide

Regency Fireplace Products

Regency Fireplace Products GOSFORD F300B Quick start guide

Regency Fireplace Products

Regency Fireplace Products Bellavista B36XTE-10 Quick start guide

Regency Fireplace Products

Regency Fireplace Products Greenfire GF900C-NG1 Quick start guide

Regency Fireplace Products

Regency Fireplace Products Greenfire GF900L Quick start guide

Regency Fireplace Products

Regency Fireplace Products HZI390E Quick start guide

Regency Fireplace Products

Regency Fireplace Products Cascades I1500 Quick start guide

Regency Fireplace Products

Regency Fireplace Products P121-NG10 Quick start guide

Regency Fireplace Products

Regency Fireplace Products Bellavista B41XT Quick start guide

Regency Fireplace Products

Regency Fireplace Products I1200S Wood Insert Quick start guide

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual