Regency Fireplace Products H2103 Quick start guide

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4

919-046d

MODELS: H2103 I3103L

WOOD

Fireplace Insert &

Hearth Heater

01.30.18

Owners & Installation Manual

Tested by:

Installer: Please complete the details on the back cover

and leave this manual with the homeowner.

Homeowner: Please keep these instructions for future reference.

www.regency-re.com

2| H2103 / I3103L

Thank-you for purchasing a REGENCY PRODUCT.

The pride of workmanship that goes into each of our products will give you years of trouble-free enjoyment. Should you have any questions about your product

that are not covered in this manual, please contact the REGENCY DEALER in your area. Keep those REGENCY FIRES burning.

“This wood heater has a manufacturer set minimum low burn rate that must not be altered. It is against federal regulations to alter this setting or otherwise

operate this wood heater in a manner inconsistent with operating instructions in this manual." Failure to follow the manual details can lead to smoke and CO

emissions spilling into the home. It is recommended to have monitors in areas that are expected to generate CO such as heater fuelling areas.

“U.S. ENVIRONMENTAL PROTECTION AGENCY Certied to comply with 2015 particulate emission standards using crib wood". Not approved for sale after

May 15, 2020.”

Model Regency H2103 – 3.5 g /hr.

Model Regency I3103 – 4.2 g/ hr.

SAFETY NOTE: If this woodstove is not properly installed, a house re may result. For your safety, follow the installation instructions, contact local building,

re o󰀩cials, or authority having jurisdiction about restrictions and installation inspection requirements in your area.

The following statements are required by the Environmental Protection Agency:

“This manual describes the installation and operation of the Regency H2103 wood heater. This heater meets the 2015 U.S. Environmental Protection Agency’s

crib wood emission limits for wood heaters. Under specic test conditions this heater has been shown to deliver heat at rates ranging from 10,800 BTU/hr. to

46,900 BTU/hr.” This unit has been tested using 5G series and generates the best e󰀩ciency when operated using well-seasoned wood and installed in the

main living areas where the majority of the chimney is within the building envelope and fully lined.”

This manual describes the installation and operation of the Regency I3103 wood heater. This heater meets the 2015 U.S. Environmental Protection Agency’s

crib wood emission limits for wood heaters. Under specic test conditions this heater has been shown to deliver heat at rates ranging from 11,900 BTU/hr. to

42,900 BTU/hr.” This unit has been tested using 5G series and generates the best e󰀩ciency when operated using well-seasoned wood and installed in the

main living areas where the majority of the chimney is within the building envelope and fully lined.”

"It is against federal regulation to operate this wood heater in a manner inconsistent with operating instructions in this manual, or if any parts are removed. “

It is against federal regulation to operate this wood heater in a manner inconsistent with operating instructions in this manual.

CAUTION: BURN UNTREATED WOOD ONLY. OTHER MATERIALS SUCH AS WOOD PRESERVATIVES, METAL FOILS, COAL,

PLASTIC, GARBAGE, SULPHUR OR OIL MAY DAMAGE THE HEATER

"This heater is designed to burn natural wood only. Higher e󰀩ciencies and lower emissions generally result when burning air dried seasoned hardwoods, as

compared to softwoods or to green or freshly cut hardwoods."

DO NOT BURN:

• Treated wood • Lawn clippings or yard waste • Manure or animal remains

• Coal • Materials containing rubber including tires • Saltwater driftwood or other previously salt water

saturated materials

• Garbage • Materials containing plastic • Unseasoned wood

• Cardboard • Waste petroleum products , paints or paint thinners or asphalt products • Paper products, cardboard, plywood or particle

board. The prohibition against burning these

materials does not prohibit the use of ﬁre starters

made from paper, cardboard, saw dust, wax and

similar substances for the purpose of starting a

ﬁre in a wood heater

• Solvents • Materials containing asbestos

• Colored Paper • Construction or demolition debris

• Trash • Railroad ties

Burning these materials may result in release of toxic fumes or render the heater ine󰀨ective and cause smoke.

The authority having jurisdiction (such as Municipal Building Department, Fire Department, Fire Prevention Bureau, etc.) should be consulted before installa-

tion to determine the need to obtain a permit.

This unit must be connected to either a listed factory built chimney suitable for use with solid fuels and conforming to ULC629 in Canada or UL-103HT in the

United States of America or code approved masonry chimney with ue liner.

H2103 is tested and certied to ULC-S628 and UL1482

I3103L is tested and certied to ULC-S628, ULC-S627 and UL1482.

SAVE THESE INSTRUCTIONS

H2103 / I3103L | 3

table of contents

Dimensions ....................................................................4

SAFETY LABEL

Safety Label For I3103L / H2103M ................................5

INSTALLATION

Before Installing Your Insert ...........................................6

Chimney Speciﬁcations .................................................6

Fireplace Speciﬁcations .................................................6

Installing Your Insert ......................................................6

Optional Flue Connector Kit ..........................................7

Masonry and Factory Built Fireplace Clearances .........7

Leg Option on H2103 Hearth Heater .............................8

Flue Connector Bracket .................................................8

Installation Into a Factory Built Fireplace .......................8

Installation Into a Masonry Fireplace .............................8

Faceplate and Trim .......................................................9

Stainless smoke deﬂector install..................................10

Fan / Blower .................................................................11

Floor Protection ...........................................................12

Firebrick Assembly ......................................................12

Door Handle ................................................................12

Brick Flue Bafﬂe & Secondary Air Tube Installation ....12

Draft Control ................................................................13

Screen Door ................................................................13

OPERATING INSTRUCTIONS

First Fire ......................................................................13

Fan Operation (All Units) .............................................13

Ash Disposal ................................................................13

Some Safety Guidelines ..............................................13

Creosote ......................................................................14

MAINTENANCE

Maintenance of Gold-Plated Doors .............................15

Door Gasket ................................................................15

Door Latch Adjustment ................................................15

Glass Cleaning ............................................................15

Glass Replacement .....................................................15

Glass Removal ............................................................15

PARTS LIST

I3103 Main Assembly ..................................................16

I3103 Faceplates .........................................................17

H2103 Main Assembly .................................................18

I3103 & H2103 Firebrick ..............................................19

WARRANTY

Warranty ......................................................................23

ALL PICTURES / DIAGRAMS SHOWN THROUGHOUT THIS MANUAL ARE FOR ILLUSTRATION PURPOSES ONLY.

ACTUAL PRODUCT MAY VARY DUE TO PRODUCT ENHANCEMENTS.

4| H2103 / I3103L

dimensions

UNIT DIMENSIONS FOR I3103L

CHK

PROCESS :

SCALE:

DWN

BLANK SIZE :

SIGN

C.N.

DATE

THIS DRAWING IS THE PROPERTY OF FPI LTD., IT MAY NOT BE COPIED IN WHOLE OR IN PART, OR DISCLOSED TO A THIRD PARTY WITHOUT OUR PRIOR WRITTEN CONSENT.

CURRENT REVISION

PREVIOUS REVISION

PART :

MAT'L :

ANGULAR =

INSIDE BEND RADII =

UNITS IN INCHES

DIMENSIONS =

TOLERANCES UNLESS

OTHERWISE STATED

SCALE

DO NOT

PROJECTION

3RD ANGLE

MODEL #

QTY.

REV.

±1°

±0.031

PART

NO.

FIREPLACE PRODUCTS INTERNATIONAL

FEB 25, 2011

SEE ABOVE

SHEAR/ PUNCH/ FORM

- WT

23MAR 2011

163-500

BLEUNG

163-500

I3100L MAIN ASSY

I3100 1

1:12

(27-1/2”)

(699mm)

(26”)

(660mm)

(15-13/16”)

(402mm)

(10-3/8”)

(263mm)

(1-7/16”)

(36mm)

(6-7/8”)

(175mm)

(44”)*

(1118mm)

(32”)*

(813mm)

(4-15/16”)

(125mm)

(9-7/16”)

(240mm) (6-1/4”)

(159mm)

(22-7/8”)

(581mm)

(5-1/2”)

(140mm)

(6”)

(152mm)

(Collar)

(952mm)

(37-1/2”)

(23-1/4”)

(590mm)

* Regular Faceplate

Oversize Faceplate is 50”W x 34 1/2” H

UNIT DIMENSIONS FOR H2103M

CHK

PROCESS :

SCALE:

DWN

BLANK SIZE :

SIGN

C.N.

DATE

THIS DRAWING IS THE PROPERTY OF FPI LTD., IT MAY NOT BE COPIED IN WHOLE OR IN PART, OR DISCLOSED TO A THIRD PARTY WITHOUT OUR PRIOR WRITTEN CONSENT.

CURRENT REVISION

PREVIOUS REVISION

PART :

MAT'L :

ANGULAR =

INSIDE BEND RADII =

UNITS IN INCHES

DIMENSIONS =

TOLERANCES UNLESS

OTHERWISE STATED

SCALE

DO NOT

PROJECTION

3RD ANGLE

MODEL #

QTY.

REV.

±1°

±0.031

PART

NO.

FIREPLACE PRODUCTS INTERNATIONAL

FEB 25, 2011

N/A

ASSEMBLY

- WT

23 MAR 2011

120-500

BLEUNG

120-500

H2100 MAIN ASSY

H2100

1:6

(28”)

(711mm)

(24-5/8”)

(625mm)

(1-5/16”)

(33mm)

(19-13/16”)

(503mm)

(54mm)

(2-1/8”)

(20-3/8”)

(517mm)

(25-7/16”)

(646mm) (5”)

(127mm)

(16-13/16”)

(427mm)

(7”)

(178mm)

(3-3/8”)

(86mm)

(6”)

(152mm)

(22-1/2”)

(571mm)

(20”)

(508mm)

(28” with legs)

(711mm)

Regular faceplate is 40 1/4 W x 30” H

Oversize Faceplate is 48”W x 33” H

(16-1/8”)

(409mm)

H2103 / I3103L | 5

safety decal

This is a copy of the label that accompanies each

Regency Hearth Heater. We have printed a

copy of the contents here for your review.

NOTE: Regency units are constantly being

improved. Check the label on the unit and if

there is a di󰀨erence, the label on the unit is the

correct one.

SAFETY LABEL FOR I3103L

SAFETY LABEL FOR H2103M

LISTED FACTORY BUILT FIREPLACE INSERT

CERTIFIED FOR USE IN CANADA AND U.S.A.

MODEL: I3100L

TESTED TO:

ULC S628-M93 / UL 1482-1998 / ULC S627-00 / UL 737-2000 REPORT NO. 632-323500 (MAR.1994)

DO NOT REMOVE THIS LABEL

106

COMPONENTS REQUIRED FOR INSTALLATION: 5.5" (140mm) or 6" (152mm) STAINLESS STEEL LINER.

OPTIONAL COMPONENT: FAN, ELECTRICAL RATING: VOLTS 115, 60 HZ, 0.6 AMPS, SCREEN DOOR

DO NOT REMOVE BRICKS OR MORTAR IN MASONRY FIREPLACE. FOR USE WITH SOLID WOOD FUEL ONLY. DO

NOT USE GRATE OR ELEVATE FIRE. BUILD WOOD FIRE DIRECTLY ON HEARTH. OPERATE WITH FEED DOOR

CLOSED, OPEN TO FEED FIRE ONLY. REPLACE GLASS ONLY WITH CERAMIC GLASS (5mm). INSPECT AND CLEAN

CHIMNEY FREQUENTLY. UNDER CERTAIN CONDITIONS OF USE CREOSOTE BUILDUP MAY OCCUR RAPIDLY. DO

NOT OVERFIRE, IF INSERT GLOWS YOU ARE OVER-FIRING.

2021

DATE OF MANUFACTURE

2020201920182017

CAUTION

908-343e

HOT WHILE IN OPERATION

DO NOT TOUCH. KEEP

CHILDREN, CLOTHING

AND FURNITURE AWAY.

CONTACT MAY CAUSE

SKIN BURNS. READ ABOVE

INSTRUCTIONS.

Install and use only in accordance with the manufacturer's installation and operating instructions. Install and use only in masonry

ﬁreplace or factory built ﬁreplace. Contact local building or ﬁre oﬃcials about restrictions and installation inspection in your area.

MADE IN CANADA

Manufactured by:

FPI FIREPLACE PRODUCTS

INTERNATIONAL LTD.

6988 Venture Street

Delta, BC V4G 1H4

(Duplicate Serial #)

Minimum Clearances to Combustibles

(Measured from insert body)

ADJACENT SIDEWALL A) 13"(330mm)

MANTLE B) 19"(480 mm)

TOP FACING C) 18"(455 mm)

SIDE FACING D) 6.5"(165mm)

INSTALL ONLY ON A NON-COMBUSTIBLE HEARTH RAISED (F) 1.5" (38mm)

ABOVE AN ADJACENT COMBUSTIBLE FLOOR. COMBUSTIBLE FLOOR

MUST BE PROTECTED BY NON-COMBUSTIBLE MATERIAL EXTENDING

(E) 16" (405mm) TO FRONT AND (G) 8" (205mm) TO SIDES FROM FUEL

DOOR.

JAN FEB MAR APR MAY JUN JUL AUG SEPT OCT NOV DEC

106

Serial No./ No de série

Part #: 908-389c

Size: 10.06" W x 3.27" H ( le at 100%)

Colour: Black on grey, except for what is highlighted in yellow is red.

Nov. 25/14: Updated ETL Logo

Jan. 22/14: Updated yrs of manufacture

Apr. 4/11:updated yrs. of manufacture / added 5.5" stainless liner

Mar. 15/10: updated yrs. of manufacture.

Jan. 2/08: updated yrs. of manufacture.

103

DO NOT REMOVE BRICKS OR MORTAR IN MASONRY FIREPLACE. FOR USE WITH SOLID WOOD FUEL ONLY. DO NOT USE GRATE

OR ELEVATE FIRE. BUILD WOOD FIRE DIRECTLY ON HEARTH. OPERATE WITH FEED DOOR CLOSED, OPEN TO FEED FIRE ONLY.

REPLACE GLASS ONLY WITH CERAMIC GLASS (5 MM).

INSPECT AND CLEAN CHIMNEY FREQUENTLY. UNDER CERTAIN CONDITIONS OF USE CREOSOTE BUILDUP MAY OCCUR RAPIDLY.

DO NOT OVERFIRE, IF INSERT GLOWS YOU ARE OVER-FIRING.

MANUFACTURED BY:

FIREPLACE PRODUCTS INTERNATIONAL LTD.

6988 VENTURE ST. DELTA, BC V4G 1H4

UNITED STATES ENVIRONMENTAL

PROTECTION AGENCY CERTIFIED TO

COMPLY WITH JULY 1990, PARTICULATE

EMISSION STANDARDS.

908-389c

HOT WHILE IN OPERATION

DO NOT TOUCH. KEEP CHILDREN,

CLOTHING AND FURNITURE

AWAY. CONTACT MAY CAUSE

SKIN BURNS. READ ABOVE

INSTRUCTIONS.

CAUTION

JAN FEB MAR APR MAY JUN JUL AUG SEPT OCT NOV DEC

ADJACENT SIDEWALL A) 10 in / 255 mm

MANTEL B) 25 in / 635 mm

TOP FACING C) 14 in / 355 mm

SIDE FACING D) 8.5 in/ 216mm

HEARTH EXTENSION (DEPTH) E) 18 in / 455 mm

HEARTH EXTENSION (ELEVATION) F) 1.5 in/ 38 mm

HEARTH EXTENSION (WIDTH) G) 6 in / 150 mm

INSTALL ONLY ON A NON-COMBUSTIBLE HEARTH RAISED (F) 1.5 IN / 38 MM

ABOVE AN ADJACENT COMBUSTIBLE FLOOR. COMBUSTIBLE FLOOR MUST

BE PROTECTED BY NON-COMBUSTIBLE MATERIAL EXTENDING (E) 18 IN / 455

MM TO FRONT AND (G) 6 IN / 150 MM TO SIDES.

COMPONENTS REQUIRED FOR INSTALLATION MUST HAVE EITHER A 5.5"

(140mm) or 6" (150MM) STAINLESS STEEL LINER.

MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS (MEASURED FROM INSERT BODY)

LISTED FACTORY BUILT FIREPLACE ACCESSORY HEARTH STOVE

CERTIFIED FOR USE IN CANADA AND U.S.A.

MODEL: H2100M

TESTED TO: ULC S628-M93 / UL 1482-1998 REPORT NO. 6255 (JULY 1991)

2015 2016 2017

DATE OF MANUFACTURE

MADE IN CANADA

(Duplicate Serial #)

INSTALL AND USE ONLY IN ACCORDANCE WITH THE MANUFACTURER'S INSTALLATION AND OPERATING INSTRUCTIONS. INSTALL AND USE ONLY IN MASONRY FIREPLACE

OR FACTORY BUILT FIREPLACE.

CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION IN YOUR AREA.

DO NOT REMOVE THIS LABEL

103

6| H2103 / I3103L

installation

CHIMNEY

SPECIFICATIONS

Before installing, check and clean your chimney

system thoroughly. If in doubt about its condi-

tion, seek professional advice. Your Regency

Insert is designed for installation into a masonry

replace that is constructed in accordance with

the requirements of "The Standard for Chimneys,

Fireplaces, Vents, and Solid Fuel Burning Ap-

pliance", N.F.P.A. 211, the National Building

Code of Canada, or the applicable local code

requirements.

The appliance, when installed, must be electri-

cally grounded in accordance with local codes or,

in the absence of local codes, with the National

Electrical Code, ANSI/NFPA 70, or the Canadian

Electrical code, CSA C22.1.

Regency Inserts are designed to use either a

5.5" (140mm) or 6" (152mm) ue.

Requirements for Installing

Solid-fuel Inserts in Factory-built

Fireplaces.

1) The insert must be tested and meet the

requirements of UL 1482 (U.S.) and or ULC

S628 (Canada) when tested in a masonry

replace built per ULC S628.

2) The factory-built replace must be listed per

UL 127 or ULC S610.

3) Clearances obtained from the masonry re-

place tests are also relevant for installation

in factory-built replaces.

4) Installation must include a full height listed

chimney liner type HT requirements (2100

degree F.) per UL 1777 (U.S.) or ULC

S635 (Canada). The liner must be securely

attached to the insert ue collar and the

chimney top.

5) Means must be provided to prevent room

air passage to the chimney cavity of the

replace. This may be accomplished by

sealing the damper area around the chimney

liner, or sealing the replace front.

6) Alteration of the replace in any manner is not

permitted with the following exceptions;

a. external trim pieces which do not a󰀨ect

the operation of the replace may be

removed providing they can be stored

on or within the replace for re-assembly

if the insert is removed.

b. the chimney damper may be removed

to install the chimney liner.

7) Circulating air chambers (i.e. in a steel

replace liner or metal heat circulator) shall

not be blocked.

8) Means must be provided for removal of the

insert to clean the chimney ue.

Regency Inserts are constructed with the high-

est quality materials and assembled under strict

quality control procedures that insure years of

trouble free and reliable performance.

It is important that you read this manual thor-

oughly and fully understand the safe instal-

lation and operating procedures. The more

you understand the way your Regency Insert

operates, the more enjoyment you will experi-

ence from knowing that your unit is operating

at peak performance.

BEFORE INSTALLING

YOUR INSERT

1) Read all instructions before installing and

using your replace insert. Install and use

only in accordance with manufacturer’s

installation and operating instructions.

2) Check your local building codes - Building

Inspection Department. You may require

a permit before installing your insert. Be

aware that local codes and regulations may

override some items in the manual.

WARNING: Careless installation is the

major cause of safety hazard. Check all

local building and safety codes before

installation of unit.

3) Notify your home insurance company that

you plan to install a replace insert or hearth

heater.

4) Your replace insert is heavy and requires

two or more people to move it safely. The

insert can be badly damaged by mishan-

dling.

5) If your existing replace damper control

will become inaccessible once you have

installed your Regency Insert, you should

either remove or secure it in the open posi-

tion.

6) Inspect your replace and chimney prior

to installing your insert to determine that it

is free from cracks, loose mortar or other

signs of damage. If repairs are required,

they should be completed before installing

your insert. Do not remove bricks or mortar

from your masonry replace.

7) Do not connect the insert to a chimney

system servicing another appliance or an

air distribution duct.

9) Inserts that project in front of the replace

must be supplied with appropriate supporting

means.

10) Installer must mechanically attach the sup-

plied label to the inside of the rebox of the

replace into which the insert is installed.

In order for a solid-fuel insert to be certied

for use in factory-built replaces, the above

information must be clearly stated in the instal-

lation manual and appropriate markings. Final

approval is contingent on the authority having

jurisdiction.

FIREPLACE

SPECIFICATIONS

Your replace opening requires the following

minimum sizes:

Height Width Depth

Large (I3103L) 25" 28" 17"

Hearth Heater (H2103M) 20.0" -- --

Two faceplates are available to seal the re-

place opening:

Standard Oversize

Large (I3103L)

44"W x 32"H 50"W x 34.5"H

Hearth Heater (H2103M)

40 1/4"W x 30"H 48"W x 33"H

INSTALLING YOUR

INSERT

Your insert is very heavy and will require two

or three people to move it into position. The

insert can be made a little lighter by removing

the cast iron door by opening it and lifting it

o󰀨 its hinges. Be sure to protect your hearth

extension with a heavy blanket or carpet scrap

during the installation.

Convection Grills for

I3103L

The convection grills are installed before the

unit is positioned inside the replace.

Position the grill on the inside bodyface side

Emissions from burning wood or gas could

contain chemicals known to the State of Cali-

fornia to cause cancer, birth defects or other

reproductive harm.

"WARNING: This replace has been converted

for use with a wood insert only and cannot be

used for burning wood or solid fuels unless

all original parts have been replaced, and the

replace re-approved by the authority having

jurisdiction."

H2103 / I3103L | 7

installation

Clearance diagram for installations

Side and Top facing is a maximum of 1.5" thick.

Floor protection must non-combustible, insula-

tive material with an R value of 1.1 or greater.

* If the hearth extension is ush with the oor

(F) it must extend 19.5" in front of the body

face (E).

Note: Hearth Extension Width (G) is meas-

ured from edge of fuel door to side

of hearth.

** A non-combustible mantel may be in-

stalled at a lower height if the framing

is made of metal studs covered with a

non-combustible board.

** Mantel depth - maximum of 10" (254mm)

MASONRY AND FACTORY BUILT FIREPLACE CLEARANCES

The minimum required clearances to combustible materials when installed into a masonry or factory built replace are listed below.

View from Rear of Insert

CONNECTOR KIT

The optional Flue Connector Kit (Part # 846-527)

and the Straight Flue Adaptor (Part #846-504)

shown here, may be used to produce a secure

connection between your ue connector and the

insert collar. Detailed installation instructions are

included with the kit.

Position the grill on the inside bodyface side

and fasten using the bolts, washers and nuts

provided (2 per side) as shown in the diagrams.

Note: The grill has a front and rear, the holes

on the front side have rounded edges

and the rear holes have at edges.

OPTIONAL FLUE

Thermal oor protection is not required if the unit is

raised 3.5" minimum (measured from the bottom of

the stove). However, standard ember oor protec-

tion is required. It will need to be a non-combustible

material that covers 16" (406 mm) in the US and

18" (450 mm) in Canada to the front of the unit and

8" (200 mm) to the sides.

If the unit is not raised, thermal oor protection

required is 18" (450 mm) in the US and Canada.

Unit

Adjacent

Side Wall

(to Side of

Unit)

Mantle**

(to Top of

unit)

Top

Facing

(to Top of Unit)

Side

Facing

(to Side of Unit)

Minimum

Hearth

Extension

Minimum

Hearth

Thickness*

Minimum

Hearth

Extension

Side

From Top of

Unit

A B C D E F G H

Large Flush

Insert I3100L

13"/330mm 19"/480mm 18"/455mm 6.5"/406mm 16"/406mm 1.5"/38mm 8"/205mm 23-1/4"/603mm

Hearth Heater

H2100M 10"/255mm 25"/635mm 14"/355mm 8.5"/216mm 18"/455mm 1.5"/38mm 6"/152mm 15-3/4"/400mm

8| H2103 / I3103L

installation

1) Positive Flue

Connection

with Cleanout

apply to the cast legs. It will be easier to attach the

legs to the stove if it is tipped on its back (prefer-

ably on a soft surface to prevent scratching).

1) Thread the bolt and washer through the

leg, and then into the nutsert in the base

of the stove and tighten.

2) Level the stove by adjusting the levelling

bolts in the bottom of each leg.

NOTE: Adding the legs changes the height of

the unit, make sure you have su󰀩cient clearance

2) Direct Flue

Connection

with Cleanout

3a) Full Flue Liner

(No Cleanout

Required)

3b) Hearth Heater with

Full Flue Liner

(No Cleanout

Required)

(min. 28") for your ue connection.

FLUE CONNECTOR

BRACKET

standing woodstove.

The H2103 can only be

installed as a Hearth

Heater i.e. vented into

a masonry or factory

built replace.

The instructions below

and fasten using the bolts, washers and nuts

provided (2 per side) as shown in the diagrams.

Note: The grill has a front and rear, the holes

on the front side have rounded edges

and the rear holes have at edges.

OPTIONAL FLUE

CONNECTOR KIT

The optional Flue Connector Kit (Part # 846-527)

and the Straight Flue Adaptor (Part #846-504)

shown here, may be used to produce a secure

connection between your ue connector and the

insert collar. Detailed installation instructions are

included with the kit.

LEG OPTION ON H2103

HEARTH HEATER

The addition of legs to the Hearth Heater does not

alter its certication, it does not become a free-

Package contains: 3 brackets and 6 screws.

These brackets are to be used to hold the ue

liner (not supplied) to the Insert and keep the

connection. The brackets are screwed into the

top of the Insert in the pre-punched holes and

then screwed into the ue liner.

Note: A clean-out door is sometimes

required, by your inspector, to be

installed when either the Positive ue

connection or Direct ue connection

method is used.

The use of one of the connection methods listed

on this page not only increases the safety of your

insert by directing the hot gases up the ue, but

will also help increase the unit's e󰀩ciency and

decrease creosote deposits in the chimney.

When a connected ue or liner is in use, the

insert is able to “breathe” better by allowing a

greater draft to be created. The greater draft can

decrease problems such as, di󰀩cult start-ups,

smoking out the door, and dirty glass.

INSTALLATION INTO A

FACTORY BUILT

FIREPLACE

1) When installed in a factory built replace, a

full stainless steel rigid or exible ue liner is

mandatory, for both safety and performance

purposes. When a ue or liner is in use, the

insert is able to breathe better by allowing

a greater draft to be created. The greater

draft can decrease problems such as, dif-

cult start-ups, smoking out the door, and

When referencing installation or connec-

tion to masonry replaces or chimneys, the

masonry construction must or shall be code

complying.

INSTALLATION INTO A

MASONRY FIREPLACE

The insert must be installed as per the require-

ments of your local inspection authority. Three

methods of ue connection are acceptable in

most areas, these include:

1) Positive ue connection, where a large

blocking plate and a short connector pipe

is used.

2) Direct ue connection, where a smaller

blocking plate and a connector pipe to the

rst ue liner tile is used.

3) Full ue liner, where a stainless steel rigid

or exible liner pipe is routed from the insert

outlet collar to the top of the chimney.

Regency highly recommends the use of a full

liner as the safest installation and provides the

most optimum performance. Your retailer should

be able to help you decide which system would

be the best for your application.

In Canada this replace insert must be

installed with a continuous chimney liner

of 5.5" (140mm) or 6" (152mm) diameter

extending from the replace insert to the

top of the chimney. The chimney liner must

conform to the Class 3 requirements of

CAN/ULC-S640, Standard for Lining Sys-

tems for New Masonry Chimneys.

H2103 / I3103L | 9

installation

Diagram 1:

H2103M and I3103L

Faceplate Assembly

3) In most cases opening the existing spark

screens fully should give enough room for

the insert installation. If it does not, remove

and store.

6) Once the above items have been checked,

slide your insert into position after rst po-

sitioning the ue liner and o󰀨set if required.

(Re-install raincap at completion of installa-

tion).

A) H2103M and I3103L Insert

1) Slide the spring nuts (supplied) over the

slots in the insert’s side convection panels

(the spring nuts may need to be squeezed

with a pair of pliers rst, to help them stay

in position).

2) Screw the side faceplate panels, (item A in

the diagram) one to each side.

3) Using the top panel (item B in the diagram)

as a gauge, check that the side panels are

within approximately 1/4" of the overall width.

If the di󰀨erence is greater than this, use

the supplied washers to attain the required

width.

B) All units

The unit may now be slid into nal position and

attached to the connection system.

Once connection is made, the insulation strips

should be installed between the insert faceplates

and the replace face. The faceplate top may

now be installed (with insulation strip behind)

by aligning its brackets with the top ange on

the side shields and the angle iron bar on the

insert top. The faceplate trim may be installed

to the edge of the faceplate at this time.

dirty glass.

2) In order to position the ue liner, the exist-

ing rain cap must be removed from your

chimney system. In most cases the ue

damper should also be removed to allow

passage of the liner.

Flush Inserts Hearth Heater

4) If the oor of your replace is below the

level of the replace opening, adjust the

insert's levelling bolts to accommodate the

di󰀨erence. When additional shimming is

required, use non-combustible masonry or

steel shims.

5) Measure approximately the alignment of

the ue liner with the position of the smoke

outlet hole on the insert to check for pos-

sible o󰀨set. If an o󰀨set is required, use a

proper stainless steel unit available with

the chimney liner.

FACEPLATE AND TRIM

Prior to sliding your insert into its nal position

and attaching the connector or liner pipe, the

faceplate side panel plates must be installed

as follows:

10 | H2103 / I3103L

installation

STAINLESS STEEL SMOKE DEFLECTOR ADJUSTMENT / REPLACEMENT

The stainless smoke deﬂector is located in the upper front area of the ﬁrebox. The deﬂector is held in place with 2 bolts

Prior to the ﬁrst ﬁre, ensure deﬂector is seated properly and secured with 2 hand tightened bolts.

To replace the deﬂector, loosen off both bolts and slide defector upward and out. Install new defector and hand tighten bolts. Ensure positive location of

the defector prior to hand tightening.

WARNING: Operation of the unit with out proper installation of smoke deﬂector will void warranty.

Smoke deector is installed through the door

opening in location shown in diagram

Smoke deector

Ensure defector is seated so bolts are situated

at the top of the keyhole before tightening.

This manual suits for next models

Table of contents

Other Regency Fireplace Products Indoor Fireplace manuals

Regency Fireplace Products

Regency Fireplace Products Bellavista B41XT Quick start guide

Regency Fireplace Products

Regency Fireplace Products L850B Quick start guide

Regency Fireplace Products

Regency Fireplace Products I100B-1 Quick start guide

Regency Fireplace Products

Regency Fireplace Products Horizon HZO42-NG Quick start guide

Regency Fireplace Products

Regency Fireplace Products P48-1 Quick start guide

Regency Fireplace Products

Regency Fireplace Products GF950L-NG Quick start guide

Regency Fireplace Products

Regency Fireplace Products PG33-NG Quick start guide

Regency Fireplace Products

Regency Fireplace Products Onyx EX110 Technical manual

Regency Fireplace Products

Regency Fireplace Products CF780 Quick start guide

Regency Fireplace Products

Regency Fireplace Products City Series ACV40ENG Quick start guide

Regency Fireplace Products

Regency Fireplace Products HZI390E Quick start guide

Regency Fireplace Products

Regency Fireplace Products GEM54-NG Quick start guide

Regency Fireplace Products

Regency Fireplace Products Energy E18E Quick start guide

Regency Fireplace Products

Regency Fireplace Products CARDINIA Quick start guide

Regency Fireplace Products

Regency Fireplace Products Cascades I1500 Quick start guide

Regency Fireplace Products

Regency Fireplace Products HZ54E-NG1 Quick start guide

Regency Fireplace Products

Regency Fireplace Products H2104 Quick start guide

Regency Fireplace Products

Regency Fireplace Products Energy U31-NG10 Repair manual

Regency Fireplace Products

Regency Fireplace Products Greenfire GFi350LNG-R Quick start guide

Regency Fireplace Products

Regency Fireplace Products P36D-NG1 Quick start guide

Regency Fireplace Products

Regency Fireplace Products Cascades I2500 Quick start guide

Regency Fireplace Products

Regency Fireplace Products City CP60E Series Quick start guide

Regency Fireplace Products

Regency Fireplace Products Pro Series Quick start guide

Regency Fireplace Products

Regency Fireplace Products City Series CC40LE-NG12 Quick start guide

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual