Redsail X700 User manual
Laser Engraver
User Manual
Applicable models：X700 、X900
济南红帆科技有限公司
R E D S A I L T E C H C O . , L T D
This type of laser machine is class GB4
laser product.Please be careful about the laser
radiation, avoid raying to eyes or skin by
direct or scattered radiation!
X700 / X900 Laser Machine User Manual
2
济南红帆科技有限公司
Redsail Tech Co., Ltd
h t t p : / / w w w . h f l a s e r . c o m
Contents
Chapter One Preface................................................................................................................................................3
Chapter Two Summary
2.1 Characteristics...........................................................................................................................................................4
2.2 Introduction of main parts..........................................................................................................................................5
Chapter Three Installation and description of accessories
3.1 How to Install Laser Tube..........................................................................................................................................6
3.2 How to connect water pipe, air pipe and air pump..............................................................................................6
3.3 How to connect the ventilators to ventilation tube...............................................................................................9
3.4 How to install the lamp........................................................................................................................................9
3.5 The instruction of the Power master control switch............................................................................................10
3.6 The instruction of the power deputy control switch............................................................................................10
3.7 How to connect USB cable..............................................................................................................................11
Chapter Four The operation instructions of the equipment
4.1 How to install software.......................................................................................................................................11
4.2 How to adjust laser beam path...........................................................................................................................12
Chapter Five Processing operation of the equipment.................................................................................................14
Chapter Six Maintenance and notes of the equipment
6.1 How to connect to ground wire..........................................................................................................................15
6.2 Maintenance of the equipment..........................................................................................................................15
6.3 Notes of the equipment.....................................................................................................................................16
X700 / X900 Laser Machine User Manual
3
济南红帆科技有限公司
Redsail Tech Co., Ltd
h t t p : / / w w w . h f l a s e r . c o m
Chapter One Preface
Sincerely thank you for choosing REDSAIL products!
This manual includes some notes and guidances about installation, test, use, the troubleshooting and daily
maintenance. In order to use it safety and correctly, please read this instruction carefully and fully understand
before operation. And please keep it well for reference in the future.
If you have any suggestions to our products or need our assistance, please call at 0531-86516855/56/57, or fax
to 0531-86516858.
Notes:
* Please turn off the power, before wiring.
* Electronic components inside the device are particularly sensitive to static electricity, so please don’t put the
foreign objects inside the device or touch the main circuit board.
1. After cutting off AC power, before the indicator light driver, main board, laser power supply turned off. There
still have high voltage inside the device, very dangerous, please don’t touch the internal circuit and components.
2. Be sure the equipment is grounding properly.
The range of application of this manual:
This manual is applicable to our X700/X900 series laser engraving and cutting machines.
X700 / X900 Laser Machine User Manual
4
济南红帆科技有限公司
Redsail Tech Co., Ltd
h t t p : / / w w w . h f l a s e r . c o m
Chapter Two Summary
This series of laser engraving machine adopts high performance two-phase stepper
motor and two-phase stepper driver, with the high speed engraving and high running
accuracy.
2.1 Characteristics：
Model
X700
X900
Laser tube
Water cooling sealed glass CO2
Control system
DSP Control system
Control software
AutoLaser
Working type
Engraving / Cutting / Punching
Image form
Plt. Ai. Dxf. Bmp. Jpg. Dst. etc.
PC interface
USB/U-Disk, support Coreldraw. AutoCAD output
directly.
Drive type
Two-phase stepper motor
Motion mode
High speed profiles bearing nylon wheel
Laser power
50W( 60W optional)
60W
Laser cooling system
Water cooling
Working size(mm)
700*500
900*600
Up and down platform (mm)
200
Working platform
Blade bed platform ( honeycomb platform optional)
Front and rear through material
Yes
Open cover protection
Yes
The workbench auxiliary lighting
Yes
The exhaust system
Yes
Assistant laser head blow
Yes
The red assistance instruction
Optional
The rotary axis system
Optional
The total power of laser machine
＜1000W
Power
AC 220V±10%/50~60HZ
Machine dimensions (mm)
1160*870*950（50W）
1410*870*950（60W）
1360*970*950
X700 / X900 Laser Machine User Manual
5
济南红帆科技有限公司
Redsail Tech Co., Ltd
h t t p : / / w w w . h f l a s e r . c o m
2.2 Instruction of main parts
Note : 1. Rear cover ( the place of laser tube, refer to 3.1)
2. The control panel
3. Assistance control switch
4. Switch box( distribution box)
5. USB input
6. The main control switch
7. Ventilator installation area
8. Water, air pipe installation area
9. Socket of the power output
10. Ground interface
11. Aviation plug installation area
X700 / X900 Laser Machine User Manual
6
济南红帆科技有限公司
Redsail Tech Co., Ltd
h t t p : / / w w w . h f l a s e r . c o m
Chapter Three Installation and description of accessories
3.1 How to install laser tube
1. Reflecting mirror frame 2. Water outlet 3. Cathode- 4.Water inlet 5. Anode+
6.holder of the laser tube 7. The laser light outlet
（Picture 1)
Please refer to figure 1 when installing the laser tube. According to the
instructions of the picture,position the anode(red wire) and cathode
wire(black/blue wire) on the laser tube with electric iron(note: the time of the
electric iron connect to the laser tube can’t last too long, in case of high
temperature burnt the laser tube),can’t virtual welding. Later, please wrap it
by high pressure adhesive tape.
After welding, please connect the water outlet pipe with the water outlet of
the laser tube, same connection for the water inlet pipe with the water inlet of
the laser tube( the connection of the water pipe follows the principle of water
from the anode to the outflow from the cathode).
3.2 how to connect water pipe, air pipe and air pump
3.2.1.1 ( how to install water pump)
X700 / X900 Laser Machine User Manual
7
济南红帆科技有限公司
Redsail Tech Co., Ltd
h t t p : / / w w w . h f l a s e r . c o m
Figure 2（2-1）
Note : 1. Water inlet 2. Water outlet 3. Air inlet 4. Water outlet 5. Water inlet 6.
Air outlet
Step of installation: 1--4 2--5 3--6
3.2.1.2( How to install the industrial chiller)
Figure 2 （2-2）
Notes: 1. Water inlet 2. Water outlet 3. Air inlet 4. Signal input of the water cooling
machine 5. Water outlet of the water cooling 6. Water inlet of the water cooling 7.air
pump 8.signal output of the water cooling machine 9. Power input 10. Water inlet of
the water cooling machine. 11. Water outlet 12. The signal wire of the water cooling
machine 13. Water pipe(2 pieces) 14. Air pipe
Installation Steps: 13(1--5) 13(2--6) 14(3--7) 12(4--8)
X700 / X900 Laser Machine User Manual
8
济南红帆科技有限公司
Redsail Tech Co., Ltd
h t t p : / / w w w . h f l a s e r . c o m
3.2.1 How to connect water pipe, air pipe and water pump( industrial chiller)
(1) Please fill the tank with water before connecting( the water level should exceed
the 3/4 of the tank, fooled the water pump)
(2) please connect the water pipe and air pipe according the figure 2.
3.2.2 the effect of the attachment:
(1) the effect of the air pump:
1. Prevent the device from the dust produced by processing the materials into the
gas nozzle, pollute focus lens.
2. Blow away dust generated during working, keep the shading of depth flat.
3. During processing, it can blow out the flame product by flammable objects.
(2) the effect of the water pump( water-cooling machine)
Must ensure the laser tube is filled with circulating water machine before working,
otherwise it will burn out the laser tube, causing irreparable damage.
When the Water, please be sure to keep the water clean, Dirty water will affect the
laser light effect and reduce the laser tube’s life( we recommended to use purified
water).
While pay attention to the water temperature, it should not exceed 35 degrees during
working. Higher temperature can cause the laser tube does not work regularly, even to
burn the laser tube.
In the north, when using the laser cutting machine in winter, the water temperature
within the tank can’t be less than 0℃. Finished the work, must be empty the water
in the laser tube, to prevent the laser tube freezing burst,the water should be at least
3/4 in the tank.
X700 / X900 Laser Machine User Manual
9
济南红帆科技有限公司
Redsail Tech Co., Ltd
h t t p : / / w w w . h f l a s e r . c o m
3.3 How to connect the ventilators to ventilation pipe
（Figure 3）
Note : 1. The mounting holes of ventilator 2. Ventilation pipe 3.ventilator (fan)
Connect the ventilator to the machine:
1.Air the end of the tube (2) on the fan outlet (1) and secure it. Then the vent pipe
is placed outdoors
2.Connect the other end of the ventilation pipe attached to the device vents(1), and
make reasonable fixed to improve the effect of exhaust smoke.
3.4 How to install the lamp
（Figure 4）
Install : figure 4, install the light tube(1) to fixed mount(2), and plug the lamp
power into the tube groove.
Other manuals for X700
1
This manual suits for next models
1
Table of contents
Popular Cutter manuals by other brands
Milwaukee
Milwaukee HEAVY DUTY M12 FCOT Original instructions
Makita
Makita DCS552 instruction manual
SignWarehouse.com
SignWarehouse.com Bobcat BA-60 user manual
Makita
Makita 4112HS instruction manual
GEISMAR STUMEC
GEISMAR STUMEC MTZ 350S manual
Hitachi
Hitachi CM 4SB2 Safety instructions and instruction manual
