RazorBack Offroad IT FITS User manual
R
A
Z
O
R
B
A
C
K
O
F
F
R
O
A
D
™
OPERATIONS MANUAL
RAZORBACK OFFROAD™
R
A
Z
O
R
B
A
C
K
O
F
F
R
O
A
D
™
Important Information Read Carefully.
Keep This Information for Further Reference.
!
Copyright 2018 Inventive Edge, LLC dba RazorBack Oroad ™ (RBO)
All information contained within this publication is based on the latest product information at the
time of publication. Due to constant improvements in the design and quality of production
components, some minor discrepancies may result between the actual parts and the information
presented in this publication. Depictions and/or procedures in this publication are intended for
reference use only. No liability can be accepted for omissions or inaccuracies. Any reprinting or reuse
of the depictions and/or procedures contained within, whether whole or in part, is expressly prohibited.
Printed in U.S.A.
RBO1018 - “IT FITS™” Spare Tire Mount Operation Manual
DOC CONTROL NUMBER RBO0052
!!
WARNING
! !!
Read, understand, and follow all of the instructions and safety
precautions in this manual and on all product labels.
Failure to follow the safety precautions could result in serious
injury or death.
It is the operator’s responsibility to follow all manufacture’s
recommendations regarding the safe operation of the vehicle.
It is the installers responsibility to follow all manufacture’s
recommendations and instructions regarding safe assembly
and installation of an accessory.
It is up to the installer that each accessory is securely mounted.
Operator must use common sense when using any RBO
accessory and when a loading rack so as not to affect the
vehicle’s safe operation.
The IT Fits Spare Tire Mount is not rated for nor should be
used as a step or hung from.
The IT Fits Spare Tire Mount should not be used as a tie-down
point for hanging items.
We recommend regular inspections and replacement of
faulty O-ring to ensure the Lugs functions as designed and to
prevent loss.
Adding mounts to the side and/or rear of the vehicle increases
its size. RBO highly recommends that you only use the RBO1018
IT FITS Spare Tire Mount on the RBO5040 Polaris RXR®900
Expedition Rack™ (Jim Todd Edition)’s tailgate location.
Ignoring these cautions and warnings could increase the
potential for accidents that could result in serious injury or death.
RAZORBACK OFFROAD™
1
Hello, and welcome to the world of Razorback Offroad™.
Thank you for your purchase of a Razorback Offroad™ (RBO)
Product. As a US-based small company, we want you to know that
each order you place means a lot to us as we grow our worldwide
family of RBO enthusiasts.
We passionately believe RBO sets new standards in UTV accessories
for excellence and design quality. We also take a lot of pride in the
fact that RBO directly creates US jobs in our small town in southern
Idaho. We believe that success is only possible by having great
customers, invested distributors, and an unwavering commitment to
both. We want you to know that we understand that your choice to
own an RBO product makes it all possible for us, and we are grateful
for the opportunity to be the choice you have made for your UTV.
We have always believed in asking ourselves - ”
Are we better today
than we were yesterday?
” to best meet our commitment of constant
improvement we ask that If you like our products, service, or wish
to reach out to us for any reason then please do so. We are always
excited to get feedback from our clients and fanatical customers.
That you would give some of your valuable time to leave a review,
watch a video about our products, visit our website, or even call
or send us a testimonial means a great deal to us.
If for any reason you are not satised with any part of the order,
the process, or our product, please let us know right away. We are
committed to doing everything we can, to make sure you are 100%
satised with all parts of our company and your experience.
Thanks again for choosing RBO and supporting us, our company and
our community!
Razorback Offroad
Mountain Home, Idaho
R
A
Z
O
R
B
A
C
K
O
F
F
R
O
A
D
™
RAZORBACK OFFROAD™
2
RECOMMENDED TOOLS FOR INSTALLATION
( Not Included )
RBO1018 - “IT FITS™” Adjustable Spare Tire Mount
Made here in Idaho, The RBO “It Fits ™” Adjustable Spare Tire Mount is a true industry rst!
With our sliding mounting studs you can easily adjust this mount to accommodate different sized tires
and wheel offsets. Not only did we design this mount to work with 10mm and 12mm wheel lugs we also
include all of the mounting hardware.
When it comes to installation, this mount has our exclusive “It Fits ™” base plate. Just look at any of our
racks and if you see the It Fits Icon you will know this mount will bolt directly onto the rack.
A Warnings
01 Welcome
02 Table of Contents & Product Introduction
03 Parts & Hardware
04 Assembly Instructions
04 Step 1 ......... Determining Length to Set the Mount
04 1.1 Establishing Bore to Surface Measurment
05 Step 2 ......... Setting the Mounting Arm
06 Step 3 .......... Attaching the Base Arm
07 Bore to Surface Measurment Recording Location
08 Step 4 .......... Stud Installation
09 12mm Lugs 4A - 4C
10 10mm Lugs 4A - 4B
11 Final Assembly
12 Warranty
13 Product Registration
14 RBO 100% Money Back Guarantee
15 Return Policy
16 Contact Information
INTRODUCTION:
• Tape Measure
• Impact Gun
• #3 Phillips Screw Driver
• 7/16” End Wrench
TABLE OF CONTENTS:
PAGE
RAZORBACK OFFROAD™
3
HARDWARE:
PARTS:
INCLUDED PARTS AND HARDWARE:
(1)
“IT FITS™” Mounting Arm
(1)
Base Arm for Spare Tire
(8)
¼” x ¾” Phillips
/ Slotted Screw
(2)
12mm Studs
(2)
10mm Lug Nuts
(2)
12mm Lug Nuts
(2)
10mm Studs
(8)
¼” Nylock Nuts
(1)
¼ Flat Washer
(2)
Nut Holders
(2)
3/8” O Rings
RAZORBACK OFFROAD™
4
The following are general instructions for assembling the RBO1018 – “IT FITS™” Adjustable Spare Tire
Mount.
Due to constant improvements in the design and quality of production
components, some
minor discrepancies may result between the actual parts and the information presented.
ASSEMBLY INSTRUCTIONS:
Determining the Length of the “IT FITS™” Adjustable Spare Tire Mount to the Spare Tire:
It is up to the installer to see that any accessory is securely mounted, and any tools used by the installer are used
and/or operated using common sense and that the installer follows the tools manufacturer’s
descriptions for intended use and recommendations.
RBO, its employees, and afliates can assume no responsibility or liability for misuse of tools and/or improper
installations that may result in breakage, damage, injury, and/or death.
!!
ATTENTION
STEP 1
(STEP 1.1)
Set the tire you wish to mount on a at surface
with the inner side facing down.
(STEP 1.2)
Measure from the at surface to the bottom edge
of the wheel’s central bore. This is the minimum
length you will need to have in order to mount
your tire to your “IT FITS™” Adjustable Spare Tire
Mount. See Figure 1. Record this measurement
in the box on page 7 for use in Step 3.3.
FLAT
SURFACE
BASE OF
CENTRAL
BORE
BORE TO
SURFACE
MEASUREMENT
(FIG. 1)
RAZORBACK OFFROAD™
5
Installation of the “IT FITS™” Support Arm
(STEP 2.1)
Place the hardware piece with the “IT FITS™”
Mounting Arm for the Adjustable Spare Tire
Mount against the location on the rack you wish
to install your “IT FITS™” Adjustable Spare Tire
Mount. At this time make sure that the facing of
the arm with the four circular holes and the single
large oval slot is facing upward.
STEP 2
(STEP 2.2)
Once the rack’s “IT FITS™” mounting bracket and
the “IT FITS™” Mounting Arm are aligned, inset a
single 1.4” x 3/4” Phillips/Slotted Screw into each
of the four holes on the “IT FITS™” Mounting
Arm, and then secure each screw with a single
1/4” Nylock Nut.
!!
WARNING
Adding mounts to the side and/or rear of the vehicle
increases its size and may affect the balance and
performance of a vehicle. RBO does not recommend
installing the RBO1018 “IT FITS™” Spare Tire Mount
anywhere but at the tailgate location.
(STEP 2.3)
With the screws and bolts in place RBO recommends
using an impact driver with a #3 Phillips attachment
with a 7/16” wrench to tighten down the “IT
FITS™” Mounting Arm to the rack.
(FIG. 2.0)
(FIG. 2.1)
See Figure 2.0
See Figure 2.1
RAZORBACK OFFROAD™
6
STEP 3
(STEP 3.1)
With the “IT FITS™” Mounting Arm now rmly attached to the rack, take the Base Arm for Spare Tire
and place it on top of the “IT FITS™” Mounting Arm.
The “IT FITS™” mounting
system is designed so that you
can quickly and easily install
onto any RBO rack any RBO
Accessory with the “IT FITS™”
icon onto any RBO Rack.
“IT FITS™” also means that these
accessories come with all the
hardware you need to install
accessories on your RBO rack
without drilling or modifying
your accessory or machine.
The “IT FITS™” mounting system
R
A
Z
O
R
B
A
C
K
O
F
F
R
O
A
D
™
Assembly of the Base arm for Spare Tire to the “IT FITS™” Mounting Arm:
(FIG. 3.0)
See Figure 3.0
RAZORBACK OFFROAD™
7
(STEP 3.2)
Next, measure from the outside edge of the Mounted “IT FITS™” Mounting Arm (Now attached ush
to your rack). Once in place, set the distance equal to the recorded measurement that was taken on
page 4 in step 1.2.
(STEP 3.3)
Move the Base Arm for Spare Tire outward until its outer edge is equal to the distance you have mea-
sured for the Bore to Surface Measurement in Step 1.2. This is the minimum distance you will need to
attach your tire to the “IT FITS™” Adjustable Spare Tire Mount.
WRITE BORE TO SURFACE MEASUREMENT HERE:
Bore to Surface Distance
(FIG. 3.1)
See Figure 3.1
RAZORBACK OFFROAD™
8
(STEP 3.6)
The remaining cap screw, closest to Tire Mount
Plate, will need the single 1/4” Flat washer to be
installed on the underside of the arm before
adding the last remaining 1/4” Nylock Nut to
secure it in place.
(FIG. 3.2)
(FIG. 3.4)
(STEP 3.4)
Continue to slide the Base Arm for Spare Tire
outward until the two holes on the side of the
Tire Mount Plate align with two holes on the “IT
FITS™” Mounting Arm. Once aligned inset, a
single a 1/4” x 3/4” Phillips/Slotted Screw into
three of the four holes on the “IT FITS™” Adjust-
able Spare Tire Mount’s Arms (One on Top and
two on the side).
See Figure 3.2
(STEP 3.5)
Place a 1/4” Nylock nut on the inside of the
channel and screw down each of the two screws
on each side of the arm and then tighten the
single screws closest on the top of the “IT FITS™”
mounting bracket using a single 1/4” Nylock Nut.
See Figure 3.3
(FIG. 3.3)
1
2
3
See Figure 3.4
(STEP 3.7)
With the screws and bolts in place RBO recommends
using an impact driver with a #3 Phillips attachment
with a 7/16” wrench to tighten down each Bolt and
nylock nut.
See Figure 3.3
This manual suits for next models
1
Table of contents
Popular Rack & Stand manuals by other brands
Salamander
Salamander Acadia AC/W/L400/WH Assembly instructions
Fohhn
Fohhn VAT-09 Mounting instruction
ricoo
ricoo FS0522 quick start guide
AMSOIL
AMSOIL BMK-22 Installation and service instructions
Kargo Master
Kargo Master 48220 installation guide
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 installation instructions
