Raven AutoBoom User manual
Goldacres Row Crop
AutoBoom Installation
Manual
Manual No. 016-0230-009 Rev B 03/17 E29365
Copyright 2017
While every effort has been made to ensure the accuracy of this document,
Raven Industries assumes no responsibility for omissions and errors. Nor is any
liability assumed for damages resulting from the use of information contained
herein.
Raven Industries shall not be responsible or liable for incidental or consequential
damages or a loss of anticipated benefits or profits, work stoppage or loss, or
impairment of data arising out of the use, or inability to use, this system or any of
its components. Raven Industries shall not be held responsible for any
modifications or repairs made outside our facilities, nor damages resulting from
inadequate maintenance of this system.
As with all wireless and satellite signals, several factors may affect the availability
and accuracy of wireless and satellite navigation and correction services (e.g.
GPS, GNSS, SBAS, etc.). Therefore, Raven Industries cannot guarantee the
accuracy, integrity, continuity, or availability of these services and cannot
guarantee the ability to use Raven systems, or products used as components of
systems, which rely upon the reception of these signals or availability of these
services. Raven Industries accepts no responsibility for the use of any of these
signals or services for other than the stated purpose.
Disclaimer
Table of Contents
Manual No. 016-0171-122 i
Chapter 1 Important Safety Information............................................................................. 1
Important Safety Information .................................................................................................................................1
Hydraulic Safety ......................................................................................................................................................................2
Electrical Safety .......................................................................................................................................................................2
Chapter 2 Introduction............................................................................................................. 3
Introduction ...................................................................................................................................................................3
Recommendations .................................................................................................................................................................4
Preparing for Installation .....................................................................................................................................................4
Point of Reference .................................................................................................................................................................4
Hydraulic Fittings ....................................................................................................................................................................4
Kit Contents ...................................................................................................................................................................5
Chapter 3 Hydraulic System.................................................................................................... 7
Install the UltraGlide Hydraulic System ..............................................................................................................7
Install Fittings on the AutoBoom Valve .........................................................................................................................7
Mount the AutoBoom Valve ..............................................................................................................................................7
Install the Pressure and Tank Hoses ...............................................................................................................................8
Install the Left and Right Cylinder Up Hoses - Single Tilt Cylinder Option ...................................................10
Install the Left and Right Cylinder Up Hoses - Dual Tilt Cylinder Option ......................................................11
Install the Left and Right Cylinder Down Hoses .......................................................................................................12
Install the Load Sense Hose .............................................................................................................................................13
Hydraulic Schematic ................................................................................................................................................14
Closed Center Hydraulic Valve ........................................................................................................................................14
Open Center Hydraulic Valve ..........................................................................................................................................15
Chapter 4 Sensors.................................................................................................................... 17
Install the UltraGlide Sensors ...............................................................................................................................17
Mount the Boom Sensors .................................................................................................................................................17
Mount the Center Rack Sensor .......................................................................................................................................18
Connect the Sensor Cables ...............................................................................................................................................18
Chapter 5 Gauge Wheels....................................................................................................... 19
Install the Gauge Wheels - Optional .................................................................................................................19
Chapter 6 Wiring...................................................................................................................... 21
Install the UltraGlide Wiring .................................................................................................................................21
Install the AutoBoom Node .............................................................................................................................................21
Connect the Harness to the AutoBoom Valve ..........................................................................................................22
Install the Center Rack Control .......................................................................................................................................23
Connect the Harness to the Unloader Coil - Open Center Valves Only .........................................................24
Connect the Harness to the Sensors ............................................................................................................................24
Connect the Harness ...........................................................................................................................................................25
Wiring Schematics ....................................................................................................................................................26
AutoBoom Controller .........................................................................................................................................................26
SCS 4000/5000 ......................................................................................................................................................................27
Viper Pro & Envizio Pro .....................................................................................................................................................28
Table of Contents
ii Viper Pro Installation & Operation Manual
Chapter 7 Replacement Parts............................................................................................... 29
Valve Block ...................................................................................................................................................................29
Sensors ..........................................................................................................................................................................30
CHAPTER
1
Manual No. 016-0230-009 Rev B 1
C hapt er 1
Important Safety
Information
Important Safety Information
Read this manual and the operation and safety instructions included with your implement and/or controller
carefully before installing the AutoBoom™ system.
•Follow all safety information presented within this manual.
•If you require assistance with any portion of the installation or service of your Raven equipment, contact
your local Raven dealer for support.
•Follow all safety labels affixed to theAutoBoom system components. Be sure to keep safety labels in good
condition and replace any missing or damaged labels. To obtain replacements for missing or damaged
safety labels, contact your local Raven dealer.
When operating the machine after installing AutoBoom, observe the following safety measures:
•Be alert and aware of surroundings.
•Do not operate AutoBoom or any agricultural equipment while under the influence of alcohol or an illegal
substance.
•Remain in the operator’s position in the machine at all times whenAutoBoom is engaged.
•Disable AutoBoom when exiting from the operator’s seat and machine.
•Do not drive the machine withAutoBoom enabled on any public road.
•Determine and remain a safe working distance from other individuals. The operator is responsible for
disabling AutoBoom when the safe working distance has been diminished.
•Ensure AutoBoom is disabled prior to starting any maintenance work on AutoBoom or the machine.
NOTICE
Chapter 1
2 Goldacres Row Crop AutoBoom Installation Manual
•When starting the machine for the first time after installing AutoBoom, be sure that all persons stand clear,
in case a hose has not been properly tightened.
•The machine must remain stationary and switched off, with the booms unfolded and supported while
installation or maintenance is conducted.
Hydraulic Safety
•Raven Industries recommends that appropriate protective equipment be worn at all times when working on
the hydraulic system.
•Never attempt to open or work on a hydraulic system with the equipment running. Care should always be
taken when opening a system that has been previously pressurized.
•When disconnecting the hydraulic hoses or purging is required, be aware that the hydraulic fluid may be
extremely hot and under high pressure. Caution must be exercised.
•Any work performed on the hydraulic system must be done in accordance with the machine manufacturer’s
approved maintenance instructions.
•When installing AutoBoom hydraulics or performing diagnostics, maintenance, or routine service, ensure
that precautions are taken to prevent any foreign material or contaminants from being introduced into the
machine’s hydraulic system. Objects or materials that are able to bypass the machine’s hydraulic filtration
system will adversely reduce performance and possibly damage theAutoBoom hydraulic valves.
Electrical Safety
•Always verify that the power leads are connected to the correct polarity as marked. Reversing the power
leads could cause severe damage to the equipment.
•Ensure that the power cable is the last cable to be connected.
WARNING
CAUTION
CHAPTER
2
Manual No. 016-0230-009 Rev B 3
C hapt er 2
Introduction
Introduction
Congratulations on your purchase of the RavenAutoBoom system! This system is designed to provide
automated boom height adjustment for agricultural equipment.
This manual applies to the following machines. For future reference, write your serial number in the space
below.
MAKE: Gold Acres
MODEL: Row Crop
YEAR:
SERIAL NUMBER:
FIGURE 1. Gold Acres Row Crop
Chapter 2
4 Goldacres Row Crop AutoBoom Installation Manual
Recommendations
Raven Industries recommends the following best practices when installing the AutoBoom system:
•Use part numbers to identify the parts.
•Do not remove the plastic wrap from a part until it is necessary for installation.
•Do not remove plastic caps from a part until it is necessary for installation.
Tools Needed
The following tools are recommended for installation of theAutoBoom system:
•SAE standard-sized wrenches
•Cable ties
•Set of tools
Preparing for Installation
Before installingAutoBoom, park the machine where the ground is level, clean, and dry. Leave the machine
turned off for the duration of the installation process.
During the installation process, follow good safety practices. Be sure to carefully read the instructions in this
manual as you complete the installation process.
Point of Reference
The instructions in this manual assume that you are standing behind the machine, looking toward the cab.
Hydraulic Fittings
This manual may reference the following types of hydraulic fittings:
•SAE O-ring fittings
•ORFS (O-Ring Face Seal) fittings
•JIC fittings
JIC fitting (M)
ORFS fitting
SAE O-ring fitting
2
Manual No. 016-0230-009 Rev B 5
Introduction
Kit Contents
This section contains a list of the components that are included in the AutoBoom kit. Before beginning the
AutoBoom installation, compare the items in the AutoBoom kit with the components on this list. If you have
questions about the kit, contact your Raven dealer.
Note: In addition to the following kit components, a wheel kit is available at an additional cost. For
available kits and ordering information, contact your Raven dealer.
TABLE 1. UltraGlide Installation Kit (P/N 117-0138-039)
Picture Item Description Part Number Qty.
Not Pictured Manual - Gold Acres AutoBoom Installation 016-0230-002 1
Not Pictured Manual - CAN AutoBoom Calibration 016-0130-062 1
Valve - AutoBoom 063-0131-125 1
Plate - Hydraulic Block Mounting 107-0171-619 1
Sensor - Right Ultrasonic 063-0130-012 1
Sensor - Left Ultrasonic 063-0130-014 1
Sensor - Center Ultrasonic 063-0130-018 1
Node - CAN Control AutoBoom 063-0130-013 1
Chapter 2
6 Goldacres Row Crop AutoBoom Installation Manual
Cable - 60” UltraGlide Sensor Extension 115-0230-602 2
Cable - Power/CAN (Prairie EF Models Only) 115-0230-007 1
Cable - PowerGlide Plus/UltraGlide CAN 115-0230-033 1
Cable - 3-Pin Din AutoBoom Adapter 115-0230-075 1
Cable - 3-Pin Din Center Rack Control
AutoBoom Adapter 115-0230-077 2
U-Bolt - 2-1/16” W x 3” L x 3/8” Thread 107-0171-609 6
U-Bolt - 2” W x 5” L x 3/8” Thread 321-0000-328 2
Bolt - 5/16”-18 x 7/8” Grade 8 Hex 311-0052-104 4
Nut - 3/8”-16 Zinc Flanged Lock 312-1001-164 16
Washer - 5/16” Zinc Plated Lock 313-1000-019 4
TABLE 1. UltraGlide Installation Kit (P/N 117-0138-039)
Picture Item Description Part Number Qty.
Other manuals for AutoBoom
26
Table of contents
Other Raven Control System manuals
Raven
Raven RS1 User manual
Raven
Raven SCS 340 Manual
Raven
Raven AccuBoom User manual
Raven
Raven SBGUIDANCE SMARTRAX MD User manual
Raven
Raven RCM-Sprayer Hawkeye 2 User manual
Raven
Raven AccuBoom User manual
Raven
Raven AccuBoom User manual
Raven
Raven DCS 410 Supplement
Raven
Raven SCS 440 User manual
Raven
Raven CR Series User manual
Raven
Raven DCS 300 Manual
Raven
Raven SCS 460 Manual
Raven
Raven SCS 360 Supplement
Raven
Raven RCM-Sprayer Hawkeye 2 User manual
Raven
Raven Viper Pro User manual
Raven
Raven SmarTrax User manual
Raven
Raven RS1/HDU User manual
Raven
Raven AccuBoom User manual
Raven
Raven AutoBoom User manual
Raven
Raven AccuFlow User manual
