Range Road RRF940 User manual
1
Table of contents
Before Using the Machine for the first time
1.Installation
1.Names and functions of respective parts.
2.Applicable engine
3.Parts to be assembled
(1) Unpacking
(2) list of parts to be assembled
(3) assembling procedure
4.Installation and movement
(1)Installation
(2)movement
(3)threading the twine
2.Inspection before operation
1.Inspection before operation
(1)Inspection of respective parts of engine
(2)Inspection of machine proper
2.Inspecting at start of engine
3.list of oiling and greasing points
3.How to operate
1.purpose of machine
2.adjustment for operation
(1) Film loading
(2) Adjustment of side roller
3.working procedure
(1) Number of turns of film
(2)Method for starting the machine
(3)Rotating speed of turn table
(4)working method
4.After completion of operation
1.Care after completion of operation
2.For storing the machine for a long period of time
2
5.Inspection and maintenance
1.Inspection and maintenance table
2.Adjustment relating to start lever
6.Trouble corrections
1.trouble corrections
3
Before Using the Machine for the first time
Before using the machine for the first time,carry out the following.
1.check the engine oil
Check whether or not a specified quantity of engine oil exists.if it is too
small,replenish the oil up filler port without screwing it,and measure. Add
oil to the top graduation line of the oil gauge.
As the oil, use the engine oil for motor vehicles with a viscosity
corresponding to the outside air temperature shown in the following
table
Oil Viscosity Selection Standard
If the engine oil declines in quality or quantity, a trouble of seizure can be caused,Use the oil with
quality of class SC or higher
In the case where the outside air temperature is lower than -20℃ or higher than 40℃,select the
oil with a viscosity and quality suitable for local condition
Note that if an oil of multi grade is used, the oil consumption tends to increase when the
air temperature is high
precaution
4
2. Check the quantity of fuel
Use lead-free gasoline for motor vehicles as the fuel
The tank capacity is about 1.5 liters.
For refueling, don’t fill up to the entrance of the fuel filler port,and keep the fuel level under the
predetermined limit line for refueling. If too much fuel is added,the fuel can bleed from fuel tank cap
dangerously
For refueling,be sure to use the fuel filter screen installed in the fuel filler port
If fire is brought close to the fuel filler port,a fire may break out.Never allow fire to approach it.During
refueling ,stop the engine
Entering a wrong fuel is dangerous. Conform once more whether or not the fuel is right
If you refuel the engine with a cigarette in your mouth or under a bare light bulb,the fuel may be
ignited to burn you,Do not refuel with fire nearby
If you refuel while the engine is still hot,the fuel may be ignited to burn you.Do not refuel while the
engine is still hot
After completion of refueling,firmly close the fuel cap,and perfectly wipe away the spilling
fuel.otherwise, a fire accident can be caused.
Precaution
WARNING
5
1. Installation
Correctly install for safe operation
1.Names and functions of respective parts
1.Main frame
The main frame supports the engine,drive unit,automatic stopping device,turn
table and stretching device
2.Handle and wheels
The handle and wheels support the machine and can be used to work
3.Drive unit
The drive unit decelerates the rotation from engine,and the belt clutch tension
is used to transmit the retation to or to isolate the ratation from the turn table.
4.Automatic stopping device
This device automatically stops the film winding around the bale
5.Turn table
The turn table has a bale mounted on it and turns it for wrapping it
6.Side roller
The roller keeps the bale in position,while the bale is wrapped
7.Stretching device
This device is loaded with a film and stretches the film from the roller driven
by the force pulling out the film.
8.start lever
This lever is used to turn on or off the rotation of the turn table
6
2.Applicable engine
The machine is designed to exhibit its performance when an adequate engine
is mounted on it.the engine of the machine has the following specification.
Engine horse power
6hp
Continuous rating 3600rpm
3.Part to be assembled
1.Unpacking
Remove the parts fixed to the packing frame
2.list of parts to be assembled
Confirm whether or not all the necessary parts are provided based on
the packing list contained in the package
3.Assembling of handle
With regard to the bolts and nuts necessary for assembling the respective
parts,see the symbols stated in the packing list
(1)Assembling of handle
Assembling the handle on the front side of the main frame of the machine
When assembling,adjust the tightening of the bolt and the flange nylon nut to ensure that the handly
can be easily moved vertically
Precaution
7
(3)Assembling of start lever
After assembling the stretching device as described in the above 3-3-(2),insert a lever B into
the bush portion at the top of the stretching device,and insert the bush into a bottom lever
A,fixing using a bolt and a flange nylon nut
It should be noted that if the bolt and the flange nylon nut are tightened extremely,the pipes of the
levers A and B may be deformed
4.Installation and movement
1.Installation
If the machine is moved at a high speed on a slope,rugged ground or along a sharp curve,it can
happen that the machine falls down on its side or tumbles down accidentally.Move slowly
If the machine is moved on a shoulder of a road with an incling side or side ditch,it can happen that
the machine tumbles down accidentally.Don’t move on a shoulder
If it is attempted to move the machine across a large level difference,it can happen that the use a
footboard
If a person rides on the machine,it can happen that the machine falls to injure
him.her.Furthermore,if the machine is moved with any thing placed on it,it can happen that the the
thing drops or that the machine falls down on its side to injure the persons working nearby.Do not
allow any person ot thing to be placed on the machine
In the case where the machine is mounted on the load carrying platform of a truck and fastened
using a rope or the like,do not wind the rope around the turn table for fixing it. The machine may be
broken
2.Inspection before start of operation
Be sure to inspect the machine before start of operation to ensure that the
machine can be used for a long period of time without any problem
Precaution
CAUTION
Precaution
8
If the inspection before start of operation is neglected,it can happen that the machine is poorly
adjusted and broken or that any person working nearby is injured accidentally.
Before starting operation,inspect the machine based on the instruction manual
1.Inspection before operation
1.Inspection of respective parts of engine
Inspect the respective parts of the engine based on the instruction manual
of the engine
2.Inspection of machine proper
(1) Check whether or not the bolts and nuts of respective parts are loose or
whether or not pins com off.
Especially check the following parts carefully.
Symbol (1):Bolt and nut for attaching the handle
Symbol (2):Lower bolt and nut for attaching the stretching device
Symbol (3):Upper bolt and nut for attaching the stretching device
Symbol (4):Cotter pins for attaching the wheels
Symbol (5):Bolts and nuts for attaching the engine
Symbol (6):Bolts and nuts for attaching the turn table
Symbol (7):Bolts and nuts for attaching sprockets 35-20T
Symbol (8):Bolt and nut for attaching sprocket 35-13T
Symbol (9):Chain tension bolt and nut
(2) Check whether the chain tension is too tight or too loose
(3) Check whether the oil and grease at respective parts is sufficient
If any oil or grease is insufficient,apply the oil or grease based on the
CAUTION
9
explanation of “2-3 List of oiling and greasing points.”
2.Inspection at start of engine
Before starting the engine,confirm that the start lever is set at “OFF position.” If the engine is started
with the start lever at “ON position,” the turn table will rotate to injure any person working nearby.
If the engine is started indoors as in a house, the exhaust gas may cause poisoning.Open windows
and door for sufficient ventilation.
Before starting the engine,let the persons working nearby know it and confirm safety.
1.Inspection at start of engine
（1）Confirm that the start lever is set at “OFF position.”
（2）Start the engine,and confirm whether or not the engine is normal
（3）Operate the start lever,to rotate the machine,and confirm whether or
not any abnormal sound or abnormal vibration occurs.
（4）
if any trouble is found,correct the trouble based on the “6-1 List trouble
corrections.”
3.List of oiling and greasing points
The oil used for lubrication or coating must be clean.
When greasing,do it till the new grease sufficiently when it is delivered.
However, confirm them before use.
No
Lubrication point
Point
Kind of lubrication
change period
remark
①
Engine
1
Engine oil for motor
vehicles
About0.4
liter
WARNING
CAUTION
10
②
Gear (turn table)
1
Greasing coating
Every 30 working hours
③
Drive chain(turn table)
1
oil
After use
④
Drive chain(automatic
stopping device)
1
oil
After use
⑤
Slide arm screw(automatic
stopping device)
1
oil
After use
⑥
Side arm shaft face
(automatic stopping device
1
oil
After use
⑦
Gear (stretching device)
1
Grease coating
Every 30 working hours
Bearings and other sliding
portions
----
Grease or oil
After use
※1.For the detail of oiling to the engine(No.1), see the instruction manual for the engine
contained in the package.
※2.If the slide arm shaft face（automatic stopping device)(No.6) is coated with a grease
with a high viscosity,the movement of the slide arm becomes poor.
3.How to operate
1.Purpose of machine
1.this machine is used to stretch and wind a film around a cylindrical bale for sealing it,to
prepare bale silage for livestock farming.Do not use the machine for any other application.
2.To prepare silage of good quality,do not operate the machine in the case where the
grass contains much water due to rainfall or dense fog,or on a muddy field or highly humid
field. Wrap the grass with an adequate water content on a well dry field as soon as
possible after baling.
1.Adjust the water content of grass to 50 to 60%.if the water content is too large or too small,ideal lactic
acid fermentation cannot take place.Especially during rainfall or dense fog,do not operate the machine
since the mater content is too large
2.Preparation of well-shaped highly dense bales.Make well-shaped highly dense bales
3.Sealing immediately after baling.If the sealing is delayed,the temperature inside the bale rises to grow
putrefying bacteria and to thermally denature proteins,thereby lowering the digestibility,not allowing
silage with good quality to be prepared.
4.Use a wrapping film with stable quality.A film like to greatly change in nature in response to the change
of air temperature may be poor in the accuracy of sealing.Preserve the film in a cool place free from
direct sunshine,to avoid the deterioration during preservation.Do not preserve the film for a long period of
time.
5.If the film used for sealing is damaged to have a hole,be sure to repair it.If a film is
damaged or holed by mistake,be sure to repair it.If an ordinary tape is used for repairing ,it
may peel due to water content,solar heat or the like.Use the repair film designated by us
6.Reliable preservation
As the place for preserving the silage,select a well drained place and cover the silage
with a net,or spray chemicals, or take any other necessary measure for protecting the
For perparing wrapped silage with good
Table of contents
Other Range Road Farm Equipment manuals
