Raex YR1226 User manual
1
YR1226 Remote Transmitter
YR1226 remote control is used to control the motors. motors fit all
kinds of electric roller blinds, canopies, Roman blinds, Venetian
blinds, projection screens, awnings, and outside solar protections.
This kind of motor integrated with a radio receiver within its casing,
No wiring is required between the motor and its control point, and is
compatible with low voltage switch.
Specification
Transmit modulate: 433.92MHz，ASK
Transmit intensity: +10dBm
Remote channel: 6 channels
Battery: CR2032×1
Remote cradle holder: optional part
Common buttons function:
1. YR1226 transmitter has six channels. Each light is one channel.
Five lights flash at the same time means the sixth channel.
[Channel choose] button can switch circularly any one channel.
2. [Up] [stop] [down] buttons separately transmit different function
signals under the current selected channel.
3. [Channel setting] key is only used to set
remote channels. Please see <setting
methods>.
2
Group buttons function:
1. Group buttons will transmit function signals under the selected
channel.
2. “[Stop] + [up]” means press [stop] key and do not release, then
press [up] key one time”.
3. [Channel setting] + [stop]——transmit “exchange direction”
signal.
4. [Channel setting] + [up]——transmit “speed up / slow-open”
signal.
5. [Channel setting] + [down]——transmit “slow down /
slow-open” signal.
6. [Stop] + [up]——transmit “startup IP1” signal.
7. [Stop] + [down]——transmit “startup IP2” signal.
Attention:
1. Transmitter will return to the first channel automatically when
without any operation within 25 seconds. This function will help
consumer default the first channel every time.
2. YR1226 radio transmitter can compatible with different radio
receivers. Different receivers will have different setting and use
methods. The operation will base on the receiver’s manual.
3. Group buttons only fit for the receivers which has corresponding
functions. Details please see receiver’s manual.
Setting methods
Before use, users must be set remote channel and sure that the
transmit signals were recorded in the receiver. As soon as the
controller receives remote signal, it will work.
3
If want to reset all the channels, please delete the remote
channels firstly, then reset.
When the work direction of the motor is different from the
control direction, you needn’t change the cable connection. You can
only correct the direction on the transmitter.
Application Example
YR1226 radio transmitter and AR8611 radio receiver setting steps:
Setting remote channel
1. Press [Learning]
key 3 seconds till the
light is on, the
controller enters into
record state.
2. Press [channel
choose] button on
the transmitter,
choose the needed
channel.
3. Press [channel
setting] key on the
back of the
transmitter. The
channel will be
recorded.
Delete remote channel
1. Press [learning] key 3 seconds
till the light is on. The controller
enters into record state.
2. Re-press [learning] key 7
seconds till the light is off.
Correct the direction
4
1. Press [learning] key 3 seconds
till the light is on. The controller
enters into record state.
3. Press [channel choose]
button, do not release. Then
press [Stop] button one time.
FCC Information
This device complies with Part 15 of the FCC rules. Operation
is subject to the following two conditions: 1) this device may
not cause harmful interference, and 2) this device must
accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try correct the interference by
one or more of the following measures:
-Reorient the receiving antenna.
-Increase the separation between the equipment and
receiver.
-Connect the equipment into and outlet on a circuit
5
different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV
technician for help.
Any special accessories needed for compliance must be specified
in the instruction manual.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
Table of contents
