RadioLabs O2 Surf User manual
Page 1of 11
O2 Surf Backfire Kit Instruction
Connecting the O2 Surf to your computer for configuration.
Connect a Category 5 Ethernet cable between your PC/MAC’s ethernet port and the LAN port of
the POE Injector.
Connect a second Category 5 Ethernet cable between the POE port of the POE injector and the
Ethernet port of the O2 Surf.
Connect the POE Injector to AC power with the included power cable.
You will not need to connect an antenna to the O2 Surf at this time; you will be prompted to do
so further along these instructions.
Before configuring your O2 Surf, you will need to disable your internal wireless card or Airport
(if applicably) and set a "static" or unchanging IP address.
To set a "static" or unchanging IP address, please follow the instructions below for your
particular operating system.
Windows:
XP: Start Menu/Windows Logo > Control Panel Select >Network Connections (if unavailable,
select show “Classic view”) Select Network Connections and right click “Local Area
Connection” and click Properties
Vista: Start Menu/Windows Logo > Control Panel > Network and Sharing Center > Manage
Network Connections > right click “Local Area Connection” and click Properties
Windows 7: Start Menu/Windows Logo > Control Panel (View by needs to be set to
"Categories")> View Network Status and Tasks > Change Adapter Settings > right click “Local
Area Connection and click Properties
Page 2of 11
Select Internet Protocol (TCP/IP) or Internet Protocol (IPv4) and click Properties
Select “Use The Following IP Address” and Enter 192.168.2.10 into the IP Address field
and 255.255.255.0 into the subnet mask field
Page 3of 11
Macintosh OS X
Select the Airport Status Icon (upper right hand corner of screen) and select “Turn
Airport Off”
Click the Apple icon in the upper left hand corner of your screen. Then click the System
Preferences.
In the Internet & Network section click the Network icon.
Page 4of 11
Select the network connection you use to connect to the internet. It will be the one that has a
green dot in front of it. The green dot means the connection is active. Then click the Configure
button which is close to the bottom of the screen.
Click the Configure IPv4 drop down box and select the Manually option.
Page 5of 11
Enter 192.168.2.10 into the IP Address field and 255.255.255.0 into the subnet mask field
Your PC/MAC is now ready to configure the O2 Surf.
Open a web browser (Internet Explorer, Mozilla Firefox, Safari, etc.) and enter 192.168.2.1 into
the address bar and hit “Enter”.
Enter “admin”(minus quotations) into both the User Name and Password field and click “Login”
(This is the default username and password for the O2 Surf, this can be changed in Advance >
Management > Web Interface Settings)
Page 6of 11
This is the main configuration page of your O2 Surf. This will show the current status of the unit
along with LAN/WLAN throughput and signal strength once the unit is configured.
Go to Advance > Basic (under Wireless Settings), set your country code, and hit apply.
Page 7of 11
Click on “Easy Setup” tab, choose “Client Router” as the operation mode, and click next.
Hit the “Site Survey” button.
Page 8of 11
Choose the wifi (click the bubble next to the SSID to select that AP) you want to connect to and
click select button.
If that wifi have a password, enter that password into the “Passphrase”.
Page 9of 11
Without making any changes to this page, click next. Now the O2 Surf will reboot.
Connecting the O2Wind to your computer for configuration.
Connect a Category 5 Ethernet cable between your PC/MAC’s ethernet port and the LAN
port of the O2Wind
Attach the antenna(s) to the O2Wind
Connect the included power cable to the router and connect to your power source. Your
O2Wind is now booting up. Please give it one to two minutes to fully boot up.
Open a web browser (Internet Explorer, Mozilla Firefox, Safari, etc.) and enter
192.168.1.1 into the address bar and hit “Enter”.
This will bring you to the RadioLabs Setup Wizard
Page 10 of 11
Select Wireless > Basic Settings
Change the SSID to what you would like to have the O2Wind rebroadcast (Home, Office, Shop
etc...)
Select "Apply Changes" then "Reboot Now".
Select TCP/IP Settings > LAN Interface
Change IP Address to 192.168.2.2
Change DHCP to Disabled.
Other manuals for O2 Surf
1
This manual suits for next models
1
Other RadioLabs Wireless Access Point manuals
