Radiant Pools Keystone User manual
Keystone Pool Assembly Manual
With proper installation, care and
maintenance, this Keystone Series
Semi-Inground Residential Swimming
Pool from Radiant Pools will provide a
lifetime of fun and relaxation for the
homeowner.
Radiant Pools offers a non-prorated,
lifetime guarantee on the entire pool
against manufacturing defects. Walls,
coping, structural supports and channels
are guaranteed against defects due to
faulty workmanship or defects due to
manufacturing for as long as you own
your home. Compare our warranty with
any other pool manufactured.
Engineering, innovation and efficiency
make the difference. It’s simply brilliant.
INTRODUCTION
The Installation of the Radiant Keystone Series Semi-Inground pool is not hard, nor complicated.
Although, installation conditions might differ from this guide, it is important to consult with the
manufacturer before making any changes that might disturb the integrity of the pool. Failure to
follow these instructions will void all warranties. Read and follow all manufacturers’ instructions
including accessories such as pumps, filters, skimmers prior to starting.
IMPORTANT: A MINIMUM OF 26” OF THE POOL WALL MUST BE BELOW THE GROUND.
Before you start, check your packing list to confirm that you have the correct number of parts
and components. The manufacturer reserves the right to revise, change or modify construction of
its pools. See packing list for pool components included for your pool. If there are any missing
or damaged components, please contact your retailer for replacement.
Even though this manufacturer’s pools are designed to meet or exceed industry recommended
safety standards, special attention must be paid to all installation procedures that the installer
performs and controls. Spend time to assure that the entire pool framework is perfectly level.
Unlevel pools place extreme pressures on the pool walls. An earth mound or pool cove must
also be installed. This keeps the pool liner from creeping out from under the pool wall. Be sure
to follow these instructions. As with any major home project, installer and/or homeowner is
responsible for following all local laws, ordinances and codes. A checklist is provided below as
a guide for these considerations.
simply brilliant.
Obtain building permit if required.
Local building and zoning requirements
Electrical requirements
Fencing requirements
Backwash (waste water) requirements
Check availability of utilities.
Call before you dig (www.digsafe.com).
If pool has steps, read the step manual.
Disposal of excavation materials
INSTALLER/HOMEOWNER CHECKLIST
✓
4
TOOLS NEEDED
Tape measure, 100ft.
Level
Short handle
square shovel
Pick or
Mattock
Tamper,
10 or 12 in. Square
Transit
Soft bristle broom
Rake
Hand Broom
Pool trowel
Hose with spray nozzle
Socket Set
Cloth rag
9/16” Open End Wrench
Screwdrivers,
Flathead and Phillips
14” Channel Locks
PVC Pipe Cutter
Flint File
Utility Knife
Rubber Mallet
Square
Coping Saw
Power Drill
Shop Vac
Wheelbarrow
Extension Cord
Long handled
pointed shovel
Masonry Sand
STRAIGHT PANEL POOL COMPONENTS
KEYSTONE SERIES POOL COMPONENTS
13
10
7
4
5
2
3
81
1 Straight Wall Panel - Form straight sides of pool.
2 Top Channel - Support top of straight walls and provide attachment for coping.
3 Bottom Channel - Provide base and structural support for straight walls.
4 Backbraces - Connects top & bottom channels together.
5 A-Frames - Fasten to backbraces & imbedded in concrete for stability.
6 Liner - Fits inside of pool to form a watertight skin.
745
oCorner Connector - Used at corner joints to join walls together.
8 Panel Connector - Join straight panels together.
9 5/4 Wood Receptor Coping (optional) - Secures liner, receives decking
10 Skimmer Assembly
11 Return Fitting
12 Light Niche Mounting Plate (optional)
13 15” Rebar - to stabilize bottom channel
# COMPONENT
6
9
12
11
The bottom channel, once assembled,
creates the framework for all remaining
assembly and must be done first. Both
top and bottom channels come with
welded extensions at one end to
connect tracks together.
To assemble, align holes on extension
over holes in channel track. Insert 3/8”
bolts with 9/16” head with washers from
beneath the bottom track using open end
wrench.
For top channel, insert bolts with washers
from above the channel.
DO NOT OVERTIGHTEN!
Check bottom track for cleanliness.
Track should be free of all dirt and debris.
Check that the bottom track is square.
(See Dig Specifications for dimensions)
The measurements from point “A” to
point “C” and from point “B” to “D”
should be the same.
CHANNEL ASSEMBLY
Top Channel
Bottom
Channel
IMPORTANT: BEFORE YOU BEGIN
The selection and preparation of the pool site is your responsibility. The manufacturer can only
suggest the proper techniques, indicate the important considerations and emphasize the precautions
and cannot be held responsible for damages to your pool that may result from failure to carefully
follow all pool specifications.
All Radiant Pool components are engineered to provide a precise fit. It is very important to handle all
components with care. Prior to assembly, all pool components should be free of sand, mud, dirt and
debris of any kind.
We recommend a small broom or shop-vac to maintain a clean track system throughout the
installation process. In addition we recommend a damp cloth be available in the event that any dirt or
debris finds its way to the panel surface.
A
C
B
D
Be sure that bottom channel and wall panels are free of debris before beginning assembly.
Connecting Straight Panels
WALL PANEL ASSEMBLY
45oCorner
Connector
Straight Panel
Connector
Connecting Panels at 450Corners
Once bottom track is assembled, begin
assembling wall panels. Always start with
the end 450corner connections first, working
towards the middle as shown. It is important
that the final panel assembled is a straight
panel connection. As wall panels are
assembled, install top channel per
channel assembly instructions on page 7.
Insert panels in bottom channel in pool interior
side of track as shown below. When connecting
the 450 corners, make sure to align the center of
the connector with the angle of the bottom track.
These must be properly aligned or installation of
subsequent panels will be difficult.
Pool
Interior
Pool
Interior
Wall Panel
Bottom Chanel
Pool
Interior
When corner panels on both ends are
assembled, begin with the straight panel
assembly, working towards the middle as
indicated above. Slide panels into bottom track,
connecting as shown at right. Continue this
process with the remaining wall panels stopping
before installing the final wall panel.
3/8" X 2 1/2" Aluminum Bolt
3/8" Nut
3/8" X 3/4" Aluminum Bolt
3/8" Nut, 3/8" Washer
3/8" X 3/4" Aluminum Bolt
3/8" Nut
3/8" X 3/4"
Aluminum Bolt
3/8" Nut
3/8" Washer
Tek screw
Top Channel
COPING CONNECTION
Tek screw
Top Channel
CP-2 Concrete Receptor Coping 5/4 Wood Deck Coping
Pool
Interior
Pool
Interior
Position backbraces and attach A-Frames
in their proper locations around the pool.
Please refer to dig specifications
for spacing and placement.
Assemble as shown.
A-FRAME & BACKBRACE ASSEMBLY
Pool
Exterior
Pool
Exterior
Backbrace
Assembly
A-Frame
Assembly
PREPARING POOL FLOOR
Bring the required amount of clean and washed masonry sand into the interior of pool
area at this time. Refer to the chart below for the required amount.
12" max.
Dished bottom (optional)
Using the masonry sand, build a pool
cove 3” to 5” high inside the wall along
the entire circumference of the pool.
This will prevent the liner from creeping
under the wall. This step is not
optional and must be done.
Spread the remaining sand equally
across the bottom of the pool. This will
give you a 2” to 3” sand base. After
the cove and base are in place, rake
and tamp the entire pool area. Make
sure that no sand is allowed to remain
on the wall above the cove. This could
cause pinholes in your liner.
Pool
Interior
PREPARING POOL COVE
26’ OCTAGON 4
15’ x 29’ 3
17’ x 33’ 4.5
17’ x 37’ 5
17’ x 40’ 5.5
Sand Amt
(cubic yds)
Pool Size
POOL COVE
POOL WALL
Once the sand has been placed inside the pool, install the remaining wall panel.
SP 1091Z10
BACK NUT
INLET FITTING
Countersunk Bolts (4)
Nuts (4)
Skimmer Mounting
Brackets (2)
Skimmer
Mounting
Plate
Skimmer
2" Male Adapter
Skimmer
Support
SKIMMER ASSEMBLY
RETURN ASSEMBLY
The return fitting is comprised of 3 pieces:
inlet fitting, SP 1091Z10 and back nut.
Install the return fitting by threading the
SP 1091Z10 into the inlet fitting. Place the
assembly into the pre-cut hole and thread
the back nut onto the SP 1091Z10 fitting.
All threaded connections should be prepared
using a combination of Teflon tape and marine
grade silicone. The return faceplate is attached
after the liner is installed.
Slide skimmer face through pre-cut skimmer
opening, keeping skimmer body on outside of
pool wall. Fasten assembly by inserting 2”
countersunk bolts through corner holes in
mounting plate, through pre-cut holes in pool
wall and through skimmer mounting
brackets, securing with hex nuts.
Tighten nuts to a snug fit.
Do not over tighten
as this will damage
the mounting plate.
Install skimmer support.
It is recommended that
2” PVC pipe be cut to size,
depending on installation.
Utilizing a 2” male adapter,
attach support to bottom of
skimmer as shown.
The skimmer faceplate
is attached after the
liner is installed.
If more inlets are desired, use a hole saw to cut proper opening.
Pool
Exterior
Pool
Interior
Table of contents
Other Radiant Pools Swimming Pool manuals
