Qtex DFOC-100 User manual
DFOC-100
User’s Manual
DisplayPort 1.4 Fiber Optic Active Cable
System requirements
- Check Source and Display parameters to meet the maximum resolution and standard
compatibility of the Product.
- Do not apply extra force or bend cable over its minimal radius.
- Do not put cable into liquids or other aggressive environments such as acids, high
temperature zones and etc.
- Since DFOC-100 uses Hybrid Technology, it does not provide galvanic isolation
between Source and Display interface ports (same as generic copper cable). Avoid
to install active hybrid cables when system has a ground loops issues or dierent line
power phase used at Source and Display installation points. It could result in failures
and electrical damages of connected equipment interfaces.
- No external power supply is needed, DFOC-100 is designed to use +5V internal
power supplied through the Source DisplayPort port.
- Do not use any intermediate cables or adapters between Source and Display ports
and the cable connectors.
- Do not connect or disconnect cable while Source and Display Devices are powered
On.
Installation
STEP 1 Carefully unpack the contents of the shipping group.
STEP 2 Power O all devices.
STEP 3 Plug ‘Source’ labeled connector directly to the DisplayPort output
interface of the Source device (Media player, PC or laptop).
STEP 4 Plug ‘Display’ labeled connector directly to the DisplayPort input interface
of the Display device (Monitor, Projector or Videowall).
STEP 5 Power On the Display device, then Source Device.
STEP 6 Check and correct resolutions settings at Source Device according Display
if needed.
STEP 7 Enjoy Clear and High Resolution Picture.
Qtex DFOC-100 cables series designed to meet extremely high requirements
of modern audio-visual systems. Cables can support up to Ultra HD 8K resolutions,
4:4:4 color sub-sampling along with multichannel audio.
DFOC-100 cables support throughout transmission of EDID signals from a display
to source device and compatible with DPCP and HDCP encrypted signals.
Two miniature converter boards integrated into the DisplayPort interface connectors
at both cable ends.
DFOC-100 is designed compact enough to t into various installation environments
with innovative technology performance. The installation is simple as for a general
copper DisplayPort cable. Thanks to its design and hybrid technology, Qtex DFOC-100
cables do not require external power supply and should be powered directly by the
DisplayPort interface of the source device. Cables are premade at dierent lengths
from 5 to 100 meters long.
© 2021 Qtex Corporation. All Rights Reserved
Revision 1.0K Dec 2021
Product View & Dimensions (mm)
Product Specifications:
• Product type: Active Fiber Optic Cable
• Complies with DisplayPort 1.4 Specications
• Supports resolutions up to 3840x2160 pixel at 120Hz or 8K at 60Hz
• Supports color sub-sampling RGB/YUV 4:4:4
• Supports EDID, DPCP or HDCP signals transmission
• Hybrid structure: 4x OM3 ber cores with 7x 30AWG copper wires
• Round Cable PVC jacket, color Black
• The maximum cable length is 100 meters
• High quality connectors with gold plated pins
• Powered by DisplayPort source (up to 300mA) without external power supply
• Maximum tensile load: 100N
• Minimum bending radius: 20mm
Environmental Specifications:
• Operating temperature: 0°C to 50°C
• Storage temperature: - 20°C to 70°C
• Humidity: 10% to 90%
Shipping Specification:
• DFOC-100 cable reel 1 pcs.
• User manual 1 pcs.
• Packing: Carton Box (size and weight depends on cable length)
Warranty Information:
Qtex warrants all optical extension cables to be free from defects in workmanship and materials, under
normal use and service, for a period of one (1) year from the date of purchasing from authorized reseller.
If a product does not work as it warranted during this period, Qtex will repair or replace
the defective product or its part. Replacement products may be new or reconditioned.
Warranty ends if the product has been damaged due to abuse, misuse, neglect, accident,
unusual physical or electrical stress, unauthorized modications, tampering, alterations, or
servicing other than by Qtex or its authorized centers, causes other than from ordinary use
or failure to properly use the Product in the application for which said Product is intended.
© 2021 Qtex Corporation. Qtex logo and its associated visual identity are trademarks or registered trademarks of Qtex Corporation
and/or subsidiaries. All other trademarks are the property of their respective owners. Qtex assumes no responsibility for any errors
that may appear in this publication. Product, pricing and feature information contained herein is subject to change without notice.
Other Qtex Cables And Connectors manuals
