Qlogic SilverStorm 9020 User manual
[Quick Start Guide ]
QUICK START GUIDE
SilverStorm™ 9020 INSTALLATION d
Purchasers of OEM products should consult with the OEM for support.
Support Headquarters QLogic Corporation
4601 Dean Lakes Blvd
Shakopee, MN 55379
QLogic Web Site www.qlogic.com
Technical Support Web Site support.qlogic.com
Technical Training Email tech.training@qlogic.com
North American Region
Email support@qlogic.com
Phone +1 952-932-4040
Fax +1 952-932-4018
All other regions of the world
QLogic Web Site www.qlogic.com
1
SilverStorm 9020
Quick Start Guide
Pre-Installation Checklist
Before beginning the actual installation, the Site Implementation Engineer must perform the following tasks:
Step 1. Check the packing list to verify all ordered equipment has been
received. The box should contain:
❑A SilverStorm 9020 switch with the following pre-installed:
❑Two (2) fan units
❑Power supplies (up to 2 total)
❑Power supply blank (up to 1 total)
❑InfiniBand (IB) leaf modules (up to 1 total)
❑Virtual I/O hardware such as the SilverStorm™ FibreChannel Virtual I/O Card (FVIC) or the SilverStorm™
Ethernet Virtual I/O Card (EVIC) (up to 2 total)
❑Any leaf/VIO hardware blanks (up to 1 total).
❑Management module(s) (up to 2 total)
❑Additional parts:
❑One (1) Hardware installation kit (mounting rails, etc.)
❑One (1) Serial cable DB-9 female to RJ-11 connector
❑One (1) Catefogy RJ-11 Serial cable
❑Power cords (up to 2 total)
NOTE: Be certain that the power cords are firmly seated into the SilverStorm 9020 power supplies AC
power inlets.
❑A CD ROM containing:
❑Technical Documentation
❑Software
❑Release Notes.
Step 2. Unpack the equipment.
Step 3. Inspect the equipment for any shipping damage.
NOTE: Any shipping damage should be reported to the shipping company.
2
Step 4. Verify that the equipment shipped matches the packing list.
Tools and Equipment Required
❑An ESD wrist strap
❑A #2 Phillips screwdriver
❑Pen (felt-tip) to mark the mounting holes on the rack
Installation Tasks
To perform the actual switch installation, the site implementation engineer must perform the following tasks, which are detailed
in this section.
Step 1. Check the installation site to verify the installation of cabinet
power feeds, rails, and grounding.
Step 2. Inspect the packaging and equipment for any shipping damage.
Any shipping damage should be reported to the shipping company. Only
unpack the the equipment if there is no shipping damage.
Step 3. Record the equipment serial numbers.
Step 4. Physically install the switch in the rack.
Step 5. Install InfiniBand (IB) or IB/Fiber Optic cables between the switch
and network devices.
Step 6. Install intra-cabinet power and grounding cables for the switch.
Step 7. Power up the switch.
Step 8. Change the default system IP address (192.168.100.9) and
gateway IP address (255.255.255.0) for the master management module.
Step 9. Add the equipment to the network.
3
Changing the IP Address and Default Gateway
Using the RS232 Serial Port
Step 1. Connect null-modem/crossover serial cables to the RS-232 ports
of the switch. If using a terminal emulation device, the settings should be:
❑8 data bits
❑no parity bits
❑1 stop bit
❑56K baud
❑Use VT100 emulation.
❑Flow control = XON/XOFF
Step 2. Power up the switch.
Step 3. To change the switch default IP address enter:
setChassisIpAddr -h ipaddress -m netMask
where -h ipaddress is the new IP address in dotted decimal (i.e., xxx.xxx.xxx.xxx) format, and -m netMask
is the new subnet mask in dotted decimal (i.e., xxx.xxx.xxx.xxx) format.
Step 4. To change the switch default gateway IP address enter:
setDefaultRoute -h ipaddress
where -h ipaddress is the new default gateway IP address in dotted decimal (i.e., xxx.xxx.xxx.xxx) format.
Using Telnet or SSH
Step 1. Power up the switch.
Step 2. Connect a Category 5 or 6 (Cat 5/6) Ethernet cable to the RJ-45
connector on the switch. Connect the other end of the Cat 5/6 to a OOB LAN
workstation.
Step 3. Access the switch with the following command:
telnet 192.168.100.9
4
Step 4. The system prompts for a user name. In order to change the IP
address and default gateway, the user must be logged in as the
administrator. At the prompt enter:
admin
Step 5. The system prompts for a password. At the prompt enter:
adminpass
The system responds with:
Welcome to the SilverStorm 9020 CLI. Type 'list' for the list of
commands.
Step 6. To change the switch default IP address enter:
setChassisIpAddr -h ipaddress -m netMask
where -h ipaddress is the new IP address in dotted decimal (i.e., xxx.xxx.xxx.xxx) format, and -m netMask
is the new subnet mask in dotted decimal (i.e., xxx.xxx.xxx.xxx) format.
Step 7. To change the switch default gateway IP address enter:
setDefaultRoute -h ipaddress
where -h ipaddress is the new default gateway IP address in dotted decimal (i.e., xxx.xxx.xxx.xxx) format.
Step 8. To to exit the CLI enter:
logout
Using the Chassis Viewer
Step 1. Power up the switch.
Step 2. Connect a Category 5 or 6 (Cat 5/6) Ethernet cable to the RJ-45
connector on the switch. Connect the other end of the Cat 5/6 to a OOB LAN
workstation.
Step 3. To start Chassis Viewer, open a web browser and enter the IP of
the switch.
NOTE: The browser must be on a workstation connected to the same Ethernet LAN, and on the same TCP/IP subnet as the
switch RJ-45 OOB LAN port.
5
Step 4. From the main menu select OOB LAN IP then Set OOB LAN IP. The
following screen is displayed:
Figure 1. Set OOB LAN IP Window
Step 5. Type in the new switch IP address.
Step 6. Type in the new net mask.
Step 7. Click Apply.
Step 8. To change the switch default gateway, from the main menu select
OOB LAN IP then Set Default Gateway IP. The following screen is displayed:
Figure 2. Set Default Gateway IP Window
Step 9. Type in the correct switch default gateway IP address.
Step 10. Click Apply.
NOTE: A reboot is required to activate the new gateway IP address.
Activating/Deactivating the Embedded Fabric Manager
If the embedded (FM) has been purchased, it requires a license key to activate it via Chassis Viewer. The license key information
is contained in an envelope marked "Fabric Manager License". This envelope is packed in the box with the switch. For detailed
information on activating the Fabric Manager, refer to the “License Keys; Key Administration” and “QuickSilver Fabric Manager
Control” sections of the SilverStorm 9000 Users Guide.
6
Installing Documentation from a CD
Installing Documentation on a Linux Host
Step 1. Place the Documentation CD in the CD-ROM drive.
Step 2. Check that the CD has been mounted. Type ls /mnt/cdrom.
The system returns a list of files on the CD.
Step 3. Create a subdirectory on the drive where the documentation will
reside.
Step 4. Type cp /mnt/cdrom/<SUBDIRECTORY NAME>
/<SUBDIRECTORY NAME> to copy the documentation to the
subdirectory created in Step 3.
Step 5. Navigate to the Documentation directory and open the desired PDF
file.
7
Declaration of Conformity
QLogic Corporation.
26650 Aliso Viejo Parkway
Aliso Viejo, CA 92656
Phone: 949.389.6000
www.qlogic.com
QLogic Corporation declares the following product is in compliance with the following standards.
Product identification:
Name: 2U Multi-Protocol Fabric Director
Model/Type: SilverStorm 9020
Standards applied:
FCC Part 15, Subpart B, Class A; ICES-003; EMC; EN55022, Class A, EN61000-3-2 and EN61000-3-3; VCCI, Class
A and EN55024
Test House:
Test report is issued by:
Name: Underwriters Laboratories Inc.
Address: 1285 Walt Whitman Road, Melville, NY 11747-3081 USA
Test dates: 2004-10-27 to 11-05
File No: E231432
Project No: 04ME12243
Vladimir Tamarkin
Director, Mechanical Engineering
8
Other manuals for SilverStorm 9020
2
Table of contents
Other Qlogic Switch manuals
Qlogic
Qlogic SANbox 5800V Series User manual
Qlogic
Qlogic SANbox2 SANbox2-64 Manual
Qlogic
Qlogic SANbox 5802V User manual
Qlogic
Qlogic SANbox 5200 Series Instruction Manual
Qlogic
Qlogic 3000 Series User manual
Qlogic
Qlogic SANbox 5802V User manual
Qlogic
Qlogic SANbox 5200 Series User manual
Qlogic
Qlogic SANbox 5600 Series User manual
Qlogic
Qlogic SANbox 1400 Series User manual
Qlogic
Qlogic SANbox 5000 Series User manual
Qlogic
Qlogic SANbox 5800V Series User manual
Qlogic
Qlogic SANbox 5600 Series Manual
Qlogic
Qlogic SANbox 1400 Series Manual
Qlogic
Qlogic SANbox2 SANbox2-64 Manual
Qlogic
Qlogic SANbox2-16 Fibre Channel User manual
Qlogic
Qlogic 5600Q User manual
Qlogic
Qlogic SANbox 9000 Series User manual
Qlogic
Qlogic StorEdge Sun StorEdge Manual
Qlogic
Qlogic SilverStorm 9040 User manual
Qlogic
Qlogic SANbox-16STD Installer's/ User manual
