Qlima ACH-312 PTC Operating manual

ACH-312 PTC

BEDIENUNGSANLEITUNG

D: WICHTIGER HINWEIS. BEDIENUNGSANLEITUNG

GB: IMPORTANT INSTRUCTION. USER MANUAL

CERAMIC OSCILLATING HEATER with DIGITAL THERMOSTAT CONTROL

READ AND SAVE THESE INSTRUCTINS

READ CAREFULLY BEFORE ATTEMPTION TO ASSEMBLE, INSRALL, OPERATE OR MAINTAIN THE

PRODUCT DESCRIBED PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY

INFORMATION. FAILURE TO COMPLY WITH

INSTRUCTIONS COULD RESULT IN PERSONAL INJURY/OR PROPERTY DAMAGE!

GENERAL SAFETY INFORMATION

1、Read all instructions before using Heater.

2、Use this Heater only as described in this manual .Any other use not recommended by the manufacture may

cause fire, electrical shock, or injury to person.

3、Make certain that the power source conforms to the electrical requirements of the Heater.

4、Extreme caution is necessary when any Heater is used by or near children or invalids and whenever the

Heater is left operating unattended.

5、This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electrical shock.

This plug is intended to fit in a polarized outlet only one way .If the plug does not fit fully in the outlet,

reverse the plug .If it still does not fit, contact a qualified electrician.

6、Where possible, avoid the use of extension cords because the extension cord may overheat and cause a risk of

fire .if they must be used, minimize the risk of overheating by ensuring that they are CUL/UL listed, a

minimum No.14AMG, rated not less than 1875 watts and of proper length.

7、Do not operate any Heater with a damaged cord or plug or after the Heater malfunctions, has been dropped or

damaged in any manner. Return Heater to authorized service facility for examination, electrical or mechanical

adjustment or repair.

8、Unplug power cord before servicing or moving the Heater. Always unplug Heater when not in use.

WARNING: DO NOT DEPEND ON THE ON/OFF SWITCH AS THE SOLE MEANS OF

DISCONNECTING POWER WHEN SERVICING OF MOVING THE HEATER. ALWAYS UNPLUG

THE POWER CORD.

9、Do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an

electrical shock or fire, or damage the Heater .Do not block or tamper with the heater in any manner while it

is in operation.

10、To prevent a possible fire, not block air intakes or exhaust in any manner. Do not place on soft surfaces, like a

bed, where opening s may become blocked.

11、Always place the Heater on a stable, flat, level surface when operating, to avoid the chance of the heater

overturning. Locate the power cord so that Heater or other objects are not resting on it, Do not run Power

Cord under carpeting .Do not cover Power Cord with throw rugs runners, or the like. Arrange Power Cord

away from room traffic and where it will not be tripped over.

RETURN INSTRUCTIONS FOR FUTURE REFERENCE

12、This Heater is hot when in use .To avoid burns, do not let b skin touch hot surfaces. Always use handle when

moving this heater, Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and

curtains at least 3 feet (0.9m) from the front of the Heater and keep at least 1foot (0.3m) from the sides and

rear.

13、A Heater has hot and arcing or sparking parts inside. It must NOT be in potentially dangerous locations such

as flammable explosive, chemical –laden or wet atmospheres, Heater is intended for general use only.

14、This Heater is not intended for use in wet or damp location. Never locate a Heater where it may fall into a

bathtub or other water container.

15、Do not use Heater outdoors.

DO NOT OPERATE THE HEATER WITH THE ALARM SOUNDING

WARNING: To avoid danger of electrical shock, unplug from outlet when not in use and before cleaning .If the

supply cord is damaged, it must be replace by a special cord or assembly available from the manufacture or its

service agent.

SAVE THESE INSTRUCTION FOR FUTURE REFERENCE

The Heater may be operation by the manual soft controls located on the Heater (as shown in FIGURE1) or by your

remote control (shown in FIGURE3).

1. Carefully remove the Heater from the plastic bag and the carton.

2. Place the heater on a firm level surface.

3. Set the main power to ‘ff’. Plug the cord set into a 220-240V ~A.C.electrical outlet. Turn the main POWER

switch to ‘ON ‘position .A ‘Beep’ sound and the red light will come on indicating that there is power to the

unit. The Heater is ready to use .The red light will remain lighted until the main POWER switch is turn OFF

and the Heater is unplugged from the electrical outlet.

4. Turn the Heater ON by pressing the ON/OFF button (FIGURE1). The unit will display the current

ROOM temperature, automatic into “FAN” mode, and blow the cold air.

5. Upon turning the heater on, the unit will be in the low heat mode.

6. Pressing the’ HEAT MODE’ button second time, the unit will set the Heater into high heat model.

7. Pressing the’ HEAT MODE’ button once more will set the Heater into AUTO mode. Notice that the display

now displays a ‘SET TEMP indicator. (See Thermostat Instruction).

8. To turn the heater OFF, press the ON/OFF button.

PARTS NAME

OPERATION

This function will work in any mode. Pressing the Swing button, the indicator will be display on the

screen, the heater will be allowed to oscillate left and right .To stop the oscillation, press the Swing button once

more.

This function will work in any mode .The timer function allows you to set the length of operation from 1hour to 8

hours. Pressing the Timer button increase the length of operation by 1hour each time the button is pressed. Once

the timer has been set, the timer will count down the hours in 1hour increments, showing on the display the

remaining operating time until the Heater will turn itself off. Pressing the Time button once more after the display

reflects 8 hours will reset the Heater to continuously running.

1. Press the HEAT MODE button until the display shows AUTO

2. To adjust “SET TEMP “, press the to increase the desired temperature and the to

decrease the desired temperature. (FIGURE 2A)

3. When the air temperature reaches 3 degrees above the SET TEMP, the heater will cut off.

4. When the air temperature drops 1degree below the SET TEMP, the unit will come back on.

Note :It is normal for the Heater to cycle ON and OFF as it maintains the SET TEMP.

SWING FUNCTION

TIMER FUNCTION

THERMOSTAT INSTRUCTIONS (FIGURE2)

REMOTE CONTROL (FIGURE3)

1. Install two “AAA”(not included) batteries as shown In FIGURE3.

2. THE Remote Control Power button is labeled as such.

All the function performed with the Remote Control work identically to the Manual Controls.

1. A thermal overload protector is built in to prevent overheating.

2. When an overeater temperature is reached, the Heater will be automatically shut off .It can only resume peration

when the user resets the unit.

(See reset instruction below)

To Reset Heater:

1. Unplug the Heater and wait 15-20 minutes for the unit to cool down.

2. Then, turn on the unit again and operate normally.

MAINTENANCE

WARNING:

-ALWAYS UNPLUG THE CORD BEFORE MOVING OR SERVICING.

-DO NOT IMMERSE HEATER IN WATER!

CLEANING :

IMPORTANT! DO NOT IMMERSE HEATER IN WATER!

Clean the Heater grill with the vacuum brush attachment on your vacuum cleaner. This will remove lint and dirt

from the inside of the heater .DO NOT ATTEMPTS TO TAKE APART HEATER .DO NOT REMOVE GRILL.

Clean the body of the heater with a soft cloth.

CAUTION: Do not use gasoline benzine , thinner, harsh cleaners ,etc.as they will damage the Heater .NEVER use

ALCOHOL OR SOLVENTS

Service: PVG Deutschland GmbH,

Telefon: +49 (0) 800 - 9427622

Fax: +49 (0) 180 - 5251450

STORAGE: Store the Heater with these instructions in the original carton in a cool, dry place.

REMOTE CONTROL

SAFETY FEATURES

Table of contents

Popular Heater manuals by other brands

oventrop

oventrop Regucor Series quick start guide

Blaze King

Blaze King CLARITY CL2118.IPI.1 Operation & installation manual

ELMEKO

ELMEKO ML 150 Installation and operating manual

BN Thermic

BN Thermic 830T instructions

KING

KING K Series Installation, operation & maintenance instructions

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Installation instructions and owner's manual

Well Straler

Well Straler RC-16B user guide

EUROM

EUROM 333299 instruction manual

Heylo

Heylo K 170 operating instructions

Eterna

Eterna TR70W installation instructions

Clarke

Clarke GRH15 Operation & maintenance instructions

IRSAP

IRSAP The Radiator Company Ovali Fitting instructions

Empire Heating Systems

Empire Heating Systems WCC65 Installation and owner's instructions

Wetekom

Wetekom 92 86 43 Original instructions

Desa

Desa SPC170-F owner's manual

Watlow

Watlow Watrod Electric Tubular Heaters Specifications

Haverland

Haverland ECO-DRY GPS Series Instruction & installation manual

Stelpro

Stelpro ASILVC2060 Series user guide