Qeedji SLATE Series User manual

User Manual

SLATE106

1.11.10 001C

Legal Notice

User Manual SLATE106 1.11.10 (001C_en)

Rights and Responsibilities

and services mentioned in this document may be trademarks and/or trademarks of their respective owners. The publisher and the author do not pretend to these

brands.

Although every precaution has been taken in the preparation of this document, the publisher and the author assumes no responsibility for errors or omissions, or for

damages resulting from the use of the information contained in this document or the use of programs and source code who can accompany it. Under no circumstances

can the publisher and the author be held responsible for any loss of profits or any other commercial prejudice caused or that would have been caused directly or

indirectly by this document.

Product information

The conception and specifications of the product may change without prior notice, and this applies to hardware, embedded software and this guide. Consumable items

accessories may slightly differ than herein described as Qeedji is depending on the evolutions of its suppliers. This document contains confidential information; it can’t

be disclosed to any third parties without prior written authorization of INNES.

Safety instructions

Please read carefully the following instructions before switching the product on: - WARNING! Correct fitting and installation is of the utmost importance. Incorrect fitting

and/or installation may result in personal injury or loss. Qeedji disclaims all liability, of whatever kind, if the product is assembled, fitted and/or installed in an incorrect

manner. - Do not use the product near a water supply. - Do not pour anything on the product, like flammable liquids or material. - Do not expose the product to direct

sun, near a heating source or a dust nor vibrations. - Do not obstruct holes, to be sure that air flows freely around the product. - Switch off the product during a storm. -

Do not open the product in any circumstances.

Guarantee terms

Qeedji products are eligible for a warranty to cover genuine manufacturing defect for 3 years. Product failure occurring as the result of factors that do not constitute

genuine manufacturing defect are not covered under the terms of the warranty and any repairs of this nature would be chargeable. For example: Inappropriate

maintenance action, a non-authorized modification, a not specified environment utilization (see ‘Safety instructions’), or if the product has been damaged after an

impact, a fall, a bad manipulation or a storm consequence, an insufficient protection against heat, moisture or frost. This warranty is not transferrable. In addition, any

repairs carried out by non-authorized personnel will invalidate the warranty.

WEEE Directive

This symbol means that your end of life equipment must not be disposed of with household waste but must be deposited at a collection point for waste electrical and

electronic equipment or to your reseller. This will benefit the environment. In this context, a system for collecting and recycling has been implemented by the European

Union

1.1
1.2
1.3
1.4
1.5
1.6
1.6.1
1.6.1.1
1.6.1.2
1.6.1.3
1.6.1.4
1.6.2
1.6.3
1.6.4
1.6.4.1
1.6.4.2
1.6.4.3
1.6.4.4
1.6.5
1.6.5.1
1.6.5.2
1.6.6
1.6.7
1.6.8
1.6.9
1.6.10
1.7
1.7.1
1.7.2
1.8
1.9
1.10
1.11
Table of Contents
Introduction
Getting started with the device
Peripherals dimensions
Device installation
Batteries
Pictureframe application
Features summary
Spe_desktop
Secondary picture display
Working with a hub
Message Overlay
File system
LED behaviour
Configuration
APPLI.CFG configuration file
APPLI.HTA configuration application
Heartbeat wake-up
Actions matrix configuration
Diagram
Device start-up
State diagram
RTC, Date & time
Software release
Recovery mode
Hardware reset
Batteries level
Mobile applications
Slate Message Overlay
Slate Maintainer (RFU)
Badge reader (RFU)
Technical specifications
Conformities
Contacts
3

1.1 Introduction

This manual explains how to setup your device SLATE106. This device is part of the SLATEs family. It can be used with or without a SMH300 hub.

Recommendations and warnings

This device is designed to be used inside a building.

This device is a Class A device. In a residential environment this device may cause radio interference. In this case, it is recommended to take appropriate measures.

This device is designed to work with 4 CR2430 batteries. Please refer to the Batteries chapter to know the batteries replacement procedure. The batteries lifetime is

estimated to 3 years with 6 daily .ppk picture updates, with Bluetooth Low Energy synchronization with SMH300 device every 15 minutes, 5/7 days, from 8:00 AM to

7:00 PM. The lifetime can be affected when using vibration features.

Keep in mind that this device is an electronics device and may not support inadvertent fall or violent vibration. In case the device has to be installed on a door, you have

to check that any violent vibration won't be generated on the device especially when closing the door. For the same reason, when the optional wake-up by vibration

feature is activated, the vibration generated when opening or closing the door may imply useless wake-up, which is affecting the battery lifetime.

The warranty does not cover the batteries.

Content of the package

Item Features

Device SLATE106

Batteries 4 CR2430 batteries with plastic holder

Support Mounting bracket and cardboard easel

Screw 2 M2.5x25

Adhesive 3M double sided tape (W x H x D): 65 mm x 19 mm x 0.5 mm

1.2 Getting started with the device

Front face

The SLATE106 device has:

3 touch sensing keys

3 red LEDs

1 RFID/NFC sensor

1 vibration sensor

Please find below the location of each peripheral:

1 RFID/NFC antenna

2 Left LED

3 Middle LED

4 Right LED

5 Left key

6 Middle key

7 Right key

8 Internal vibration sensor

Side face

8 USB client cable (Male micro-B)

Rear face

9 Mounting bracket

Device dimensions

151,2

114

Labelling

The model of the device, the power supply characteristics, the serial number (PSN) and the MAC address are written on a label which is stuck on the case. Some

additional tags may be present in case of built-in options.

☛ The serial number of the device can be requested in case of technical support.

00:1E:C0:40:04:BF

Mac:

5VInput:

SLATE106

5A rue Pierre Joseph Colin

35000 Rennes, FR

PSN00901-00104 CD5

www.qeedji.tech

130mA

3 7 0 0 5 6 8 1 0 5 9 9 1

SLATE106

EAN

www.qeedji.tech

Testcard

At the factory, the device content set by default is the Test Card . The chart displays important information to assist in the device configuration:

SLATE106

Manufacturer: Qeedji (www.qeedji.tech)

PSN: 00902-00077

Firmware rev: 1.10.12

Software rev: 1.11.10

Hostname: slate106

Index: 2

1.3 Dimensions

Dimensions in millimeters

Coordinates [X,Y] in pixels

15 151.2

114

90.6

122.4

11.7

14.4

6.8

103.9

60.9

17.9

118.1

25.6

5.7

2.4

2.5

[0;0]

[799;599]

[688;25]

[109;575]

[117;583]

[125;591]

[390;575] [398;583]

[406;591]

[671;575] [679;583]

[687;591]

1.4 Device installation

Batteries

Place the SLATE106 device, with the back face in front of you.

Keep the battery in its plastic holder like shown below.

1 CR2430 battery

2 Battery holder

⚠ Warning: check that the battery is inserted in its holder with the right polarity (positive side facing up). In case the battery is not delivered with its holder,

contact [email protected].

Glide the 1st battery 3 with its holder into its place. Use your finger or a screwdriver to push the plastic of the holder part until you feel a clip, meaning that the battery

is properly installed.

Glide the other batteries with its holder in the right orientation like explained on the picture above:

2nd battery 4,

3rd battery 5,

4th battery 6.

Once the batteries are installed, they are all hidden.

CR2430 CR2430

CR2430