Quick Start Guide
Wall Switch Products
WS1D, WS1DL, WS1R, WS1E, RWS
©2012 Powerline Control Systems, Inc.
All Rights Reserved v2.0
19201 Parthenia St. Suite J
Northridge, CA 91324
P: 818.701.9831 F: 818.701.1506
www.pcslighting.com
DE-RATING INFORMATION FOR WS1D
For a proper fit in a multiple gang installation, it may be
necessary to remove one or both sides (break-off tabs) from the
mounting plate. When tabs are removed, the overall rating of
the device must be reduced in accordance with the following
chart:
Model Max
Load
No Fins
Removed
Normal
Depth
Box
No Fins
Removed
Deep Box
One Fin
Removed
or Next
to One
Dimmer
Both Fins
Removed
Or Next
to Two
Dimmers
WS1D-6 600W 600W 600W 500W 400W
WS1D-10 1000W 900W 1000W 800W 600W
MULTI-WAY CIRCUITS
The Wall Switch is wired directly to the lighting circuit and can
(optionally) be controlled by one or more RWS Remote Wall
switches producing three, four or five-way circuits. Multi-way
circuits make it possible for a group of switches to control the
same set of lights. This section will illustrate how to wire the
connections.
Note:
1. Refer to Figures 1 and 2 to determine the wire colors of the connections.
2. All PCS Wall Switches require a neutral (white) connection.
3. Remote Wall Switches require that the Line (black) wire be accessible. This wire
may be connected to either phase of the 120/240V supply.
4. The gray wire on the Remote Wall Switch can be connected to either earth
ground or neutral. The gray wire serves only to light the LED in the remote. This
LED does not indicate anything except that power is applied and to serve as a
night-light.
CONFIGURATION
Once your WS1 is installed it can be configured either manually
or with the UPStart Setup Software.
Manual configuration can be used to add your WS1 device into a
UPB network and link it to controller buttons. Refer to the
Keypad Controller’s Manual Configuration Guide for more
details.
Although the factory default operation of the WS1 is useful in
many situations, it is highly recommended that your device be
configured with UPStart Setup Software so that you can take
advantage of its many configurable features.
PCS has developed a Powerline Interface Module (PIM) and free
UPB Setup Tool software (UPStart) to help you configure all of
your PulseWorx Lighting System devices. User’s Guides are
available to explain how to configure your system from our
website.
SETUP MODE
When configuring a UPB system, it will be necessary to place the
WS1 in SETUP mode. To do this, tap the Rocker Switch five times
rapidly. The lighting load will flash one time and the Status LED
will continuously blink Blue when the device is in SETUP mode. To
exit SETUP mode, tap the Rocker Switch once or wait five minutes
for it to time out.
OPERATION
The WS1 can be a member of up to 16 scenes with the capability to
store a pre-set relay state (on, off, or blink) for each scene. The
WS1 will accept powerline commands from any UPB-compatible
transmitter such as PulseWorx Keypad Controllers, Timed Event
Controllers, Wall Switches, Interface Modules, and approved Third-
Party Controllers.
STATUS LED INDICATOR
The WS1 comes equipped with a multi-color status LED indicator
that is normally lit to blue. This LED indicator will blink different
colors to indicate UPB ® communication status and configuration
status as outlined below. Note: By using UPStart Setup Software, the Status
LED can also be configured to stay one solid color or to change colors based on the
state of the load.
LED Color Status
BLUE Power applied to Wall Switch
MAGENTA Receives message for Wall Switch
BLACK Receives message for another device
RED Switch is transmitting a UPB® message
CERTIFICATION
This product has been
thoroughly tested by either
Underwriters Laboratories or
Intertek Testing Services, nationally recognized independent third-
party laboratories. The North American UL/ETL Listed mark signifies
that the product has been tested to and has met the requirements
of a widely recognized consensus of US and Canadian product
safety standards, that the manufacturing site has been audited,
and that the manufacturer has agreed to a program of quarterly
factory follow-up inspections to verify continued conformance.
LIMITED WARRANTY
Seller warrants this product, if used in accordance with all
applicable instructions, to be free from original defects in materials
and workmanship for a period of five years from the date of
purchase. Refer to the warranty information on the PCS website
(www.pcslighting.com) for exact details.
