PSC LazerData Series 9000E User manual

INSTALLATION AND

OPERATION MANUAL

LazerData Series 9000E

BARCODE SCANNER/DECODER

PSC Automation, Inc.

675 Basket Road

Webster, New York 14580-9787

(800)-828-6489

(716) 265-1600

(716) 265-6400 (Fax)

INSTALLATION AND OPERATION

MANUAL

LazerData Series 9000E

BARCODE SCANNER/DECODER

Part No. 7902033

Revision E

August 1997

FOREWORD

The purpose of this manual is to provide sufficient information and data

to install, program, operate, and maintain the LazerData Series 9000E

Bar Code Reading System. PSC Automation, Inc. has made every

effort to ensure that the information in this manual is both accurate and

adequate. It is recommended, in the interest of safety and efficiency,

that each section be carefully read before installing or servicing this

system. Special attention should be given to the items outlined in

Section 1, READ THIS FIRST, before proceeding further.

This manual may not be copied or reproduced, in whole or in part,

without the express written consent of PSC Automation, Inc.

August 1997

TABLE OF CONTENTS

11 Read This First

Introduction 1-1

FCC Class A Statement 1-1

NCDRH Compliance Statement 1-1

Safety Precautions 1-3

Optical Safety 1-3

Electrical Safety 1-3

22 Introduction

System Description 2-1

Technical Specification 2-1

Principals of Operation 2-3

33 Installation

Introduction 3-1

Unpacking and Inspection 3-1

Mounting Provision 3-2

Power Requirements 3-5

Specular Reflection 3-5

Mounting Orientation 3-5

Raster 3-9

44 Signal Interfaces

Introduction 4-1

Local Port 4-1

Host Port 4-2

I/O Port 4-6

Power Connector 4-10

Mating Connectors 4-11

TABLE OF CONTENTS

55 Local Formatting

Introduction 5-1

Startup 5-2

Terminal Selection 5-4

Main Menu 5-6

Gate Parameters 5-7

Field Definition Summary 5-12

Field Definition Detail 5-14

Host Port Formatting 5-19

Local Port Formatting 5-25

Output Pulse Configuration 5-30

Save Data/Base Configuration 5-34

Diagnostics 5-36

Compare String - Summary 5-38

Compare String - Detail 5-40

66 Host Programming

Introduction 6-1

Programming 6-2

Commands 6-3

AAppendix

Glossary of Terms

READ THIS FIRST

1-1

INTRODUCTION

This section contains vital information necessary for proper installation,

operation and maintenance of the LazerData Series 9000E

Scanner/Decoder Bar Code Reading System. Each item in this section

should be read completely before proceeding to other sections of this

manual. If any questions arise please contact LazerData Applications

Engineering at 1-800-843-2700 for clarification.

FCC CLASS A STATEMENT

This equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with this manual, may cause

interference to radio communications. It has been tested and found to

comply with the limits for a class A computing device pursuant to

Subpart J of Part 15 of the Federal Communication Commission rules,

which are designed to provide reasonable protection against such

interference when operated in a commercial environment. Operation of

this equipment in a residential area is likely to cause interference, in

which case the user, at his own expense, will be required to take

whatever measures may be required to correct the interference.

NCDRH COMPLIANCE STATEMENT

This laser bar code scanning system complies with Standard 21 CFR,

Subchapter J, for Class I and Class II laser products as set forth by the

National Center for Devices and Radiological Health. Any alteration or

adjustment that could result in emission of radiation in excess of the

level established for Class I or Class II laser products is not authorized,

and will void certification of the system as a Class I or Class II laser

product. Figure 1-1 on the following page shows the type and location of

warning labels affixed to the scanner in compliance to the NCDRH

standard. The Caution and Aperture labels do not apply to the Class I

Infrared scanners.

Series 9000E Scanner/Decoder

1-2

NOTE: A ^L (Control L) sent to the Local or Host Port of the Series

9000E Scanner/Decoder will turn the Laser Beam on or off.

Warning Label Placement

Figure 1-1

READ THIS FIRST

1-3

SAFETY PRECAUTIONS

The LazerData Series 9000E Bar Code Scanning System incorporates

features that provide for maximum safety. However, it must be

recognized that any equipment employing electrical voltage and emitting

direct or scattered radiation may cause serious damage and/or personal

injury if improperly handled. The following are recommended

safeguards that should be observed at all times.

OPTICAL SAFETY

Never stare directly into the laser beam.

CAUTION: Use of optical instruments with this product will

increase eye hazard.

ELECTRICAL SAFETY

Disconnect the main power line before working on any electrical

equipment.

Always use insulated tools.

CAUTION

Use of controls, adjustments or performance of

procedures other than those specified herein may

result in exposure to hazardous radiation or

electrical voltages.

Series 9000E Scanner/Decoder

1-4

Table of contents

PSC LazerData Series 9000E User manual

Popular Barcode Reader manuals by other brands