PSA LIFESAVER 6000WIRM User manual

1203-7201-00

Part Number: LIF6000WIRM

Wireless Interlink and Relay Module for

LIFESAVER range of smoke alarms and

ancillary products.

This product is AC mains powered with

rechargeable battery backup.

Wireless Interlink Relay Module

Model 6000WIRM

Contents

1. Product Features And Specifications .................................................................................................................... 2

2. Operational Features .........................................................................................................................................................3

3. Installation Instructions.................................................................................................................................................... 4

4. Activation and RF Interlink Network .......................................................................................................................12

5. Warranty ...................................................................................................................................................................................15

1. Product Features And Specifications

•Electrical rating: 240 V AC 50Hz with 2 X 3V rechargeable battery back up

•Relay contacts rating: 240VAC/30VDC 5A.

•Low Battery : The red LED flashes once every 30 seconds.

•Multi-purpose green and red LEDs indicate the module is connected to the AC supply,

is working normally and wireless link status.

•Link button is used to interconnect wirelessly, and test.

•Wireless Radio Frequency: 918 MHz

•Wireless range of < 100 meters in open air (Line of sight)

•Wireless Interconnect: up to 24 units

•The module can be interconnected through hardwire or wirelessly

•Hardwire Interconnect Alarms: Up to any combination of 12 other non-wireless alarms.

•Operating Temperature Range: 0°C to 40°C

•Selectable relay options: (1) Smoke Alarm Latching, (2) Smoke Alarm Pulse, or (3) CO latching.

•Battery Life: At least 3 days as backup power (without alarms).

•Approved to AS/NZS 4268:2017

•Approved to AS/NZS CISPR 32:2015 AMD 1:2020

•Approved to AS/NZS 62368.1:2018

2. Operational Features

The Lifesaver 6000WIRM is a mains powered wireless interlink module that allows hard wired Lifesaver smoke

alarms to be connected to a wireless network. The built-in relay can be activated when smoke alarms or

devices are activated. The module is fitted with a rechargeable backup battery.

The unit is designed to be mounted on the ceiling or wall.

Wireless interconnect: up to 24 units, compatible models:

LIF6000WB, LIF6000DCW, LIF6000THL

Hardwire interconnect up to 12 units, compatible models:

LIF5800ACF, LIFCO240, LIF6000/RL, LIFHA240

The Isolation Relay provides a set of Normally Closed (NC) and Normally Open (NO) change over contacts.

This enables smoke alarms to trigger auxiliary devices such as strobe lights, sirens, bells, burglar and fire alarm

panels, activate emergency lights, shut down air conditioners or release magnetic door holders.

This isolation relay has 3 selectable modes of operation.

Select the mode of operation using the selector switch(See Figure 1).

CO Relay(CO):

•When CO relay is selected, the relay

will latch only when CO alarm is in

alarm condition.

SM latching Relay(SM-C):

•Relay stay latched or continuously

activated while smoke

and /or heat alarm in

alarm condition

SM Pulse Relay(SM-P):

•Relay activate momentarily for

2 seconds when the smoke

and /or heat alarm in alarm

condition

Selector Switch

SM-C

SM-P

Figure 1

LED indication

There are two LED indicators. Each of them has a unique function:

This relay module has two LED indicators (Red and Green).

The LEDs indicate the following:

Green

•ON – AC Power is Present

•OFF – AC Power is not Present

Red

•LED flashes one second ON and one second OFF : Out of box, searching for network, ready to join or

create a new network.

•Two quick LED flashes every 2 seconds : CRD – Unit is set as Master

•Three quick flashes every 2 seconds: RFD – Unit is set as Slave

•LED blinks four times twice: Unit is in general reset condition and is now in stand-alone mode

•LED flashes every 2 seconds: Indicates loss of wireless interconnection.

•LED flashes every 30 seconds: Indicates low battery

3. Installation Instructions

The wireless relay module must be on a circuit breaker and

be installed in a suitable location such as the ceiling or wall.

Refer to the local building regulations and codes of

practice.

!Disconnect mains power before commencing work.

A. Remove cover (cover screws) to allow access

to wire connections. See Figure 2.

Use a small screw driver to open the cover.

Please note: The cover is clipped into place and can only

be closed in one direction.

Figure 2

Mark and drill two holes

for wall or ceiling anchors.

6.5mm

Wall

Expansion pipe

2.4mm 22mm

4.0mm

B. Mount base plate on proper location.

Figure 3

Relay Smoke/Heat/CO alarm

Terminals are classed as hazardous circuits. Tighten terminal

screws to 0.8 N.m max.

C. Wire the cables into the appropriate terminals. Then turn ON the battery switch.

Selector switch

Battery switch

Figure 4

C. Wire the cables into the appropriate terminals. Then turn ON the battery switch. D. After the cables are connected, re-install the module cover. See Figure 5 below.

Figure 5

Wiring Instructions

The wireless interlink relay module can be used for signalling compatible Lifesaver equipment or to activate

auxiliary warning devices such as external bells and sirens, hallway or stairwell lighting. It provides isolated (no

internal connection to 240 volts AC), normally open, and normally closed contacts.

!WARNING! Alarm and relay module wiring installation must comply with the current edition of AS3000

and Wiring Regulations and all appropriate prevailing local regional / national building regulations / codes of

practice.

To be installed by a qualified electrician. Failure to install this product correctly may expose the user to

electric shock or fire risk hazards. This relay module is not rated as waterproof and must not be exposed to

dripping or splashing water. The relay module must be installed correctly in order to function. The electrical

circuit used to power the alarms and the relay module must be 240 volt AC 50Hz. This relay module has a

rechargeable battery backup to allow it to function in the event of mains power outage.

!WARNING: This product cannot be operated from power derived from a square wave, modified square

wave or modified sine wave inverter. These type of inverters are sometimes used to supply power to the

structure in ‘off grid’ installations, such as solar or wind derived power sources. These power sources produce

high peak voltages that can damage the device.

!IMPORTANT: Whenever alarms and relay modules are interconnected they must be powered on a

single circuit. It is recommended to connect the module and alarms to a dedicated circuit that is separately

electrically protected. This helps minimise interference (EMI) on alarm interconnect line from CFL’s, dimmers,

LV transformers etc.

• This 6000WIRM relay module will not detect smoke or heat and must be installed in conjunction with the

specified alarms. Only connect to the specified models of smoke or heat alarm. Do not connect to any other

brand of alarm/auxilary device unless approved by PSA.

• The earth terminal connection provided is for termination purposes only and is NOT electrically connected

within the sealed alarm / base units.

WARNING: THIS WIRELESS MODULE MUST BE INSTALLED BY QUALIFIED (LICENSED)

ELECTRICIANS ONLY.

• In the interests of safety, this wireless module and all wiring must be installed by a licensed electrician in

accordance with the relevant requirements of the SAA Wiring Rules - AS3000.

• This wireless module can only interconnect with compatible smoke alarms. Interconnection with other

brands may cause damage, result in electric shock, fire risk and void warranty.

• It is important that the alarm be wired correctly to ensure correct operation. Incorrect wiring to the Smoke

Alarm will damage the unit and void the warranty.

• Terminals on the module are marked as follows:

WARNING: Connecting the Switch wire terminal to any other supply conductor may result in

damage to the alarm, failure to operate or shock hazard and void the warranty of the alarm.

RELAY OPERATION

The wireless relay may take a few seconds to operate when the smoke alarm or carbon monoxide alarm is

activated. This is due to the time to receive the wireless signal. Conversely, when the smoke alarm or carbon

monoxide deactivates, the relay may take a few seconds to deactivate.

MARKINGS

NO Normally Open

CCommon

NC Normally Closed

A ACTIVE

SW SWITCH WIRE (FOR INTERCONNECTION ONLY)

NNEUTRAL

LOOP DEAD TERMINAL

Relay (select settings page 3)

Smoke/Heat/CO alarm

240V SUPPLY

LIF6000 SERIES

SMOKE ALARM

LIF6000WIRM

NCNO

To sirens, sounders,

lights and auxiliary

devices.

A S N 9A S N A S N

LOOP

CO/ HEAT ALARM

SM pulse

SWTICH

SM latching

By installing the LIF6000WIRM in this manner it will allow you to operate devices such as sirens,

strobes, bells, lights, air conditioners or any devices which do not exceed 240VAC @ 5 Amps.

The wiring connecting the module with the external device is not supervised. Be sure to test the operation of

all the devices controlling the module or controlled by the module. Devices controlled by the module can be

tested by pushing the Link button on the relay and verifying that the controlled device responds in the desired

manner. Devices controlling the module can be tested by activating the device and verifying that all of the

interconnected alarms enter into alarm.

Connecting to Auxiliary Devices, see Figure 6.

Figure 6

This manual suits for next models

Table of contents

Popular Relay manuals by other brands

Shelly

Shelly Pro Series user manual

GE MVAX 11 Technical manual

ABB

ABB RELION REF615R manual

Pilz

Pilz PNOZ X10 Technical instructions

ABB

ABB SPAJ 142 C User manual and technical description

Kemo Electronic

Kemo Electronic B197 quick guide

Seg

Seg MRM3 manual

Basler

Basler BE1-700C manual

CD Automation

CD Automation REVEX 2PH 280A user manual

Ruelco

Ruelco 1S04 Operation manual

Basler

Basler V3E Z1P B2C1F instruction manual

Doepke

Doepke Dupline DSM 2 operating instructions

Siemens

Siemens SIRIUS 3RT1966-4D Original operating instructions

GE DGP instruction manual

Kyongbo Electronics

Kyongbo Electronics GDR-D01 user manual

Siemens

Siemens SIPROTEC 4 user manual

Siemens

Siemens BD2-AK03X/FS Series installation instructions

Leuze

Leuze MSI-SR5B Original operating instructions