Proxicast LAN-Cell LC2-411 User manual

Proxicast, LLC

312 Sunnyfield Drive

Suite 200

Glenshaw, PA 15116

1-877-77PROXI

1-877-777-7694

1-412-213-2477

Fax:

1-412-492-9386

E-Mail:

support@proxicast.com

Internet:

www.proxicast.com

WAN Fail-Over & Traffic Redirect

Technote LCTN0011

Proxicast is a registered trademark and LAN-Cell, and LAN-Cell Mobile

Gateway are trademarks of Proxicast LLC. All other trademarks

mentioned herein are the property of their respective owners.

LCTN0011: WAN Fail-Over & Traffic Redirect

Page 1

This TechNote applies to LAN-Cell models:

LAN-Cell 2:

LC2-411 (firmware 4.02 or later)

CDMA: 1xMG-401

1xMG-401S

GSM:

GPRS-401

Minimum LAN-Cell Firmware Revision: 3.62(XF2).

Note for Original LAN-Cell Model (1xMG & GPRS) Users:

The WAN Fail-Over & Traffic Redirect screens in the original LAN-Cell’s Web GUI differ slightly from the

examples in this Technote. See the LAN-Cell’s User Guide for more information on WAN Fail-Over & Traffic

Redirect configuration.

Document Revision History:

Date Comments

November 12, 2008 Initial Release

LCTN0011: WAN Fail-Over & Traffic Redirect

Page 2

Introduction

The LAN-Cell offers 2 distinctly different mechanisms for ensuring that WAN-bound traffic is routed to an available

WAN gateway.

WAN Fail-Over

WAN Fail-Over is the LAN-Cell’s method of monitoring its internal WAN interfaces (Ethernet wired WAN port,

Cellular 3G modem WAN port, and Dial-Backup serial port) and sending packets to the highest priority interface

that is operational. (Note: The LAN-Cell 2 also offers WAN load balancing – that topic is not covered here.)

Traffic Redirect

Traffic Redirect is a technique the LAN-Cell uses to reroute WAN-bound traffic to a different LAN subnet that

contains another WAN gateway device (e.g. another LAN-Cell or third-party router).

Each mechanism has advantages and is appropriate for different network topologies. WAN Fail-Over and Traffic

Redirect can be used in tandem to provide an unprecedented level of WAN availability. In both instances, the

LAN-Cell routes packets directly to the interfaces based on a user-defined priority scheme.

WAN Fail-Over is used when all of the LAN-Cell’s interfaces are directly connected to WAN access devices such

as DSL/Cable modems, satellite modems, analog telephone modems, etc. Traffic redirection is used when

additional WAN access is provided by another network device such as a router or gateway located on a different

subnet from the LAN-Cell. Under traffic redirection, the LAN-Cell passes all WAN-bound traffic to the remote

gateway whenever the LAN-Cell’s primary and backup WAN interfaces are not available.

This TechNote illustrates examples of WAN Fail-Over and Traffic Redirection.

LCTN0011: WAN Fail-Over & Traffic Redirect

Page 3

Example 1: WAN Fail-Over

You can assign a relative routing priority to each of the LAN-Cell’s WAN interfaces (wired Ethernet, Cellular,

Traffic Redirect and Dial-Backup). The LAN-Cell uses these values to determine the interface to which packets

are routed. When configured to WAN Fail-Over mode, the LAN-Cell will attempt to use the next lowest priority

interface as higher priority interfaces become unavailable.

In this example, the LAN-Cell 2 is being used to provide redundant Internet connectivity to a remote office LAN.

The primary WAN connection is a DSL modem, backed up by a 3G Cellular modem and finally by a 56Kbps

telephone modem.

Figure 1 shows the LAN-Cell 2 with a DSL modem connected to the wired Ethernet WAN port, a 3G cellular

modem card inserted, and a dial-up analog telephone modem connected to the AUX (serial) port. All three of

these WAN interfaces will be available to the LAN-Cell on a relative priority basis. The LAN-Cell will fail-over

among these interfaces automatically with little or no impact on the LAN PC’s connected to the LAN-Cell. When a

higher priority interface becomes available again, the LAN-Cell will “fall-back” to use that interface.

Figure 1: Example WAN Fail-Over Network Topology

Usage Notes

•By default, the LAN-Cell is configured for automatic fail-over / fall-back between the wired Ethernet WAN

(highest priority) and the Cellular 3G modem (second highest priority). The Dial-Backup WAN (serial) port

is not enabled by default and has the lowest routing priority.

•The Dial-Backup WAN port must have a lower priority (higher metric value) than either the WAN or

Cellular interfaces.

•The same basic configuration can be used with cable modems, T1 lines, satellite modems, etc.

Configure each WAN interface as necessary for a connection.

•The wired WAN port can also be connected to a LAN port on another router rather than directly to a

modem (a cross-over cable may be required). The LAN address of the secondary router must be in a

different subnet than the LAN-Cell’s LAN IP address/subnet.

•There is additional information on LAN-Cell WAN, Cellular, and Fail-Over configuration parameters in the

LAN-Cell User’s Guide.

LCTN0011: WAN Fail-Over & Traffic Redirect

Page 4

LAN-Cell Configuration

First, configure the WAN, Cellular and Dial-Backup interfaces for your specific equipment and connection type.

In our example, the DSL modem has a static IP address of 23.4.147.160 / 255.255.240.0 with a default remote

gateway of 24.3.144.1 (Figure 2).

Figure 2: WAN Parameters

The CDMA cellular modem needs only the ISP Access Phone Number of #777 set. It will receive a dynamic IP

address from the carrier (Figure 3).

Figure 3: Cellular Parameters

LCTN0011: WAN Fail-Over & Traffic Redirect

Page 5

The Dial-Up modem needs its PPP username, password and ISP telephone number entered along with a modem

initialization command string (Figure 4).

Figure 4: Dial-Backup Parameters

LCTN0011: WAN Fail-Over & Traffic Redirect

Page 6

Next, select the NETWORK->WAN menu, then the General tab (Figure 5).

Figure 5: Configuring WAN Fail-Over

Ensure that the Operation Mode is set to Active/Passive. Select Fall Back to Primary WAN When Possible if

you want to use the secondary WAN interfaces only when necessary.

Set the relative Route Priority of each WAN interface; typically the wired Ethernet WAN is the highest priority and

Cellular is the second highest, however you can reverse these values if your Cellular connection has higher

bandwidth, lower cost or if you there is some other reason to prefer the Cellular connection over a wired Ethernet

connection.

Although not required, using the Continuity Check feature in conjunction with WAN Fail-Over can improve the

LAN-Cell’s responsiveness to failed connections. The Continuity Check feature periodically sends an ICMP (ping)

packet out of the selected interface(s) to determine the “end-to-end” continuity of communications. This helps the

LAN-Cell detect certain types of “hung” connections which are not reported “down” at the physical layer.

Check Period – how often to send the ICMP packets (e.g. every 5 seconds)

Check Timeout – how long to wait for an ICMP reply from the target IP address (max latency)

Check Fail Tolerance – number of consecutive reply failures before the interface is considered “down”

Where possible, selecting Ping Default Gateway will give the most reliable results. However some ISP’s (and

most cellular network operators) do not respond to ICMP packets sent to their gateways. In these cases, select

another well-know and reliable IP address or domain name as the target. Your own mail or web server is often

reasonable choice. Avoid using “public” hosts such as Google or Microsoft as these servers may not respond to

ICMP packets in the future, thereby effectively disabling your WAN interface(s) on the LAN-Cell.

Note: On earlier LAN-Cell models, the Continuity Check feature is not available.

LCTN0011: WAN Fail-Over & Traffic Redirect

Page 7

Testing WAN Fail-Over

The easiest way to test if WAN Fail-Over is working is to remove one or more of the WAN interfaces. In our

example, removing the cable from the LAN-Cell’s WAN port to the DSL modem will force the wired WAN interface

to go down and the Cellular interface to become active. You can test Internet connectivity by pinging some

Internet IP address or going to a remote web page.

When you reconnect the WAN cable, you will see alerts in the LAN-Cell’s log indicating that the WAN connection

is up, the Cellular connection has been taken down and that the LAN-Cell has fallen back to use the primary WAN

connection (Figure 6).

Figure 6: WAN Fall-Back Alert

You can test failure of both the WAN and Cellular interfaces by removing the WAN cable, and then disabling the

Cellular card on the WAN->CELLULAR page. This will cause the LAN-Cell to make a dial-up connection using

the external telephone modem.

Note About DNS Resolution

In a WAN Fail-Over situation, you may have issues with resolving DNS names to IP addresses. If you are able to

connect to Internet hosts via their IP address but not their DNS name, the issue is most likely that your ISP’s are

not permitting DNS lookups from devices outside of their network.

The LAN-Cell is a caching DNS-relay server. You should configure your LAN devices to use the LAN-Cell’s LAN

IP address as their DNS server – the LAN-Cell will forward DNS requests to the proper ISP based on the currently

active WAN interface.

LCTN0011: WAN Fail-Over & Traffic Redirect

Page 8

Example 2: Traffic Redirect

The LAN-Cell also supports a “virtual” WAN interface called Traffic Redirect. You can indicate the IP address of

backup gateway (a device that has its own pathway to the WAN) to which the LAN-Cell will forward all packets

whenever the LAN-Cell has no primary or secondary direct WAN connection.

In this example, the LAN-Cell 2 is on a network that includes another gateway router. This router could be

another LAN-Cell, for example, one with a 3G cellular modem for a different carrier than the primary LAN-Cell. Or

the secondary gateway could be an existing router with a slower, higher cost WAN connection.

Figure 1 shows the example LAN-Cell 2 with only a 3G cellular modem card inserted. The LAN-Cell is on a

common Ethernet LAN segment with the secondary gateway.

Figure 7: Example Traffic Redirect Network Topology

Usage Notes

•The LAN-Cell and the backup gateway must be on different IP subnets but on the same physical network.

You can connect the backup gateway directly to one of the LAN-Cell’s LAN ports.

•LAN client devices should set the primary LAN-Cell as their default gateway. The traffic redirect function

will route the packets to the backup gateway with no configuration changes necessary on the client

devices.

•Traffic Redirect works when either the wired WAN, Cellular WAN or both are configured on the primary

LAN-Cell.

•The routing priority of Traffic Redirect must be lower than the WAN and Cellular interfaces.

•There is additional information on the Traffic Redirect and IP Alias configuration parameters in the

LAN-Cell User’s Guide.

LCTN0011: WAN Fail-Over & Traffic Redirect

Page 9

LAN-Cell Configuration

Configure the primary LAN-Cell for its normal WAN/Cellular operation.

Configure the backup gateway for its normal operation and WAN connectivity

Notice that in the example shown in Figure 7, the LAN-Cell and the backup gateway are on different logical IP

subnets on the same physical network (LAN-Cell = 192.168.1.1 and backup gateway = 192.168.0.1). This is

required for Traffic Redirect to work properly. To handle this situation, an IP Alias (VLAN) must be defined on the

LAN-Cell to allow it to make a LAN connection to the backup gateway’s subnet in addition to its own subnet.

Select NETWORK->LAN->IP ALIAS from the LAN-Cell’s menu (Figure 8). Enable IP Alias #1 and enter a valid IP

address that is part of the backup gateway’s subnet. Do not enter the backup gateway’s address here. Check

with the administrator of the backup gateway’s subnet to determine a valid IP address for the LAN-Cell’s IP Alias.

Also, you may need to enable RIP for the LAN-Cell and backup gateway to properly exchange routing

information.

Figure 8: LAN IP Alias Parameters

Next, go to the NETWORK->WAN->TRAFFIC REDIRECT screen. Enable the Traffic Redirect feature and enter

the LAN IP address of the backup gateway (Figure 9).

Figure 9: Traffic Redirect Parameters

By enabling Traffic Redirect, the WAN Continuity Check feature is automatically enabled for the Traffic Redirect

interface (Figure 10). The backup gateway’s IP address is selected as the target destination; if the backup

gateway does not respond to ICMP packets, enter the address or DNS name of another device to check. The

Continuity Check feature is used to determine if the Traffic Redirect interface is available. You may optionally

configure the WAN & Cellular continuity check parameters as required by your application.

Note: On earlier LAN-Cell models, the Continuity Check feature is not available.

This manual suits for next models

Table of contents

Other Proxicast Network Router manuals

Proxicast

Proxicast LAN-Cell 2 User manual

Proxicast

Proxicast EtherLINQ User manual

Proxicast

Proxicast LAN-Cell 3 User manual

Proxicast

Proxicast EtherLINQ User manual

Popular Network Router manuals by other brands

Allnet

Allnet ALL0333AU user guide

HomeSeer

HomeSeer HT-SEL Getting started guide

Sercomm

Sercomm Genesis OC3505D Quick installation guide

Billion

Billion BIPAC 5102 Series user manual

TP-Link

TP-Link TD-8817 QIG

Motorola

Motorola MR1900 user guide

Digi

Digi IX14 user guide

Cisco

Cisco NCS 540 Hardware installation guide

XAVi

XAVi X8821e user manual

BEC

BEC 6200WZL Quick installation guide

MikroTik

MikroTik hAP ac3 Series quick start

Korenix

Korenix JetNet 5428G Series user manual

NETGEAR

NETGEAR FS526T - Switch installation guide

Korenix

Korenix JetNet 5710G Series user manual

Automated Logic

Automated Logic ZN551 Technical instructions

Cisco

Cisco ASR 1000 Series Installation and configuration guide

EnGenius

EnGenius ESR-9710 quick start guide

Cisco

Cisco 805 Series Product overview