Prospec INFPRV450 User manual

*This stereo should not be washed with a pressure

washer neither should it be washed with chemicals.

A wet sponge or damp cloth will suffice.*

This product is serviced exclusively by Prospec Electronics Inc. and must be

returned to Prospec for in and out of warranty repairs. It can not be serviced

under warranty by other Infinity service centers.

For service contact us :

3325 South Morgans Point Road Mt Pleasant SC 29466

Tel 843-849-9037

Or visit: www.prospecelectronics.com

INFPRV450 Owner’s Manual

3325 South Morgans Point Rd. | Mt. Pleasant, SC 29466

. .

P: 843 849 9037 | www.prospecelectronics.com

Table of Contents

Table of Contents ----------------------------------------------------------------- 1

Product Description -------------------------------------------------------------- 2

Installation Instructions ---------------------------------------------------------- 3

Wiring Configuration ------------------------------------------------------------ 4

General Function of Buttons ---------------------------------------------------- 5

General Operations --------------------------------------------------------------- 7

General Settings ------------------------------------------------------------------ 7

Radio Section Operation ------------------------------------------------------- 10

SiriusXM Section Operation ----------------------------------------------- 12

Bluetooth Section Operation -------------------------------------------------- 16

USB Section Operation -------------------------------------------------------- 18

iPod/iPhone Operation --------------------------------------------------------- 20

AUX Section Operation -------------------------------------------------------- 21

Troubleshooting ----------------------------------------------------------------- 22

Troubleshooting

Advisory Name

The radio has detected a fault with the SiriusXM antenna. The antenna

cable may be either disconnected or damaged.

Verify that the antenna cable is connected to the SiriusXM Connect

Vehicle Tuner.

Inspect the antenna cable for damage and kinks. Replace the antenna

if the cable is damaged.

SiriusXM products are available at your local car audio retailer or

online at www.shop.siriusxm.com.

The following information helps you self-diagnose common issues without the need for

contacting SiriusXM support.

Recommended Description

Check Antenna

The radio is having difficulty communicating with the SiriusXM

Connect Vehicle Tuner. The tuner may be disconnected or damaged.

Verify that the SiriusXM Connect Vehicle Tuner cable is securely

connected to the radio.

Check Tuner

No Signal The SiriusXM Connect Vehicle Tuner is having difficulty receiving

the SiriusXM satellite signal.

Verify that your vehicle is outdoors with a clear view of the sky.

Verify that the SiriusXM magnetic mount antenna is mounted on a

metal surface on the outside of the vehicle.

Move the SiriusXM antenna away from any obstructions.

Inspect the antenna cable for damage and kinks.

Consult the SiriusXM Connect Vehicle tuner installation manual for

more information on antenna installation. Replace the antenna if the

cable is damaged. SiriusXM products are available at your local car

audio retailer or online at www.shop.siriusxm.com.

Subscription

Updated

The radio has detected a change in your SiriusXM subscription status.

Press ENTER button to clear the message.

Visit www.siriusxm.com or call 866-635-2349 in the USA or 877-

438-9677 in Canada if you have questions about your subscription.

Channel Not

Available

The channel that you have requested is not a valid SiriusXM channel

or the channel that you were listening to is no longer available.

You may also see this message briefly when first connecting a new

SiriusXM Connect Vehicle tuner.

Visit www.siriusxm.com for more information about the SiriusXM

channel line up.

Channel Not

Subscribed

The channel that you have requested is not included in your SiriusXM

subscription package or the channel that you were listening to is no

longer included in your SiriusXM subscription package.

In the U.S.A., visit www.siriusxm.com or call 1-866-635-2349 if you

have questions about your subscription package or would like to

subscribe to this channel. In Canada, visit www.siriusxm.ca or call

1-877-438-9677.

Channel Locked The channel that you have requested is Locked by the radio Parental

Control feature. See the description on Parental Control, page 14 for

more information on the Parental Control feature and how to access

locked channels.

Product Description

This Infinity PRV450 incorporates a 3.5” TFT color screen, ready to complement

your day whether you are on the water, motorcycle, UTV trail, or farm. Following

the same footprint as the popular INFPRV250, this stereo is synonymous with

excellence. In fact, the INFPRV450 was listed as one of the top new products of

2016 by Boating Industry magazine. Check in with us often to see what the next

Prospec experience will bring!

The INFPRV450 incorporates the following features:

AM/FM

Bluetooth Audio Streaming with ID tagging

USB input and control-for USB drives only

Auxiliary input

3.5” color TFT screen / Waterproof faceplate

50W x 4 amplifier

Wired remote option

U.S. and European tuning

Charging through USB

3 pair of RCA output including subwoofer output

SiriusXM-Ready (SiriusXM connect tuner and subscription required)

Can Bus Control via NMEA2000

The Infinity brand is part of Harman International Industries. In 1958, Harman

Kardon developed the world’s first stereo receiver and we are proud to bring

you the world’s first Infinity marine color screen receiver!

Sirius, XM and all related marks and logos are trademarks of Sirius XM Radio

对折基准线

Troubleshooting

*Note: In many respects, a stereo acts much like a computer and occasionally requires a

reboot. In the unlikely event of product malfunction, a reset can usually fix the issue.

For software reset operation, please refer to page 8.

Issue

No power

No Sound

No Reception

USB stick not

reading

Cause

1. Incorrect wiring

2. Fuse is blown

3. Low battery voltage

1. Speaker connection

came loose

2. Bad speaker

3. Output blown

4. Volume too low on

media device

1. Antenna not firmly

seated in socket

1. File must be a mp3

or wma file

Solution

1. Double check wiring

2. Replace fuse

3. Check voltage of vehicle battery

with multimeter. Voltage must

be at least 11V.

1. Double check connections.

2. Replace bad speaker with known

good speaker and connect.

3. Send unit in for repair.

4. Increase volume of media device

1. Insert firmly

1. Convert format to mp3 or mwa.

While in Bluetooth mode:

No Connection 1. You are not connect

to the “PRV”

address on your

portable media

device.

2. Out of range

3. The connection is

already in use.

1. Choose “PRV”

2. Bring portable media device closer

to the receiver. Device needs to be

within 30’.

3. Ask the person who first paired to

drop out.

Installation

A mounting gasket has been added inside the package for convenience. Trace along

the outside edge of the gasket thus revealing your cutout.

Mounting Illustration

1. Avoid installing stereo

below cupholders!

Make sure mounting

substrate is flat to avoid

flexing of the plastic.

2. Use the back bracket and

studs to affix the unit. Install

the U bracket behind the unit,

using two nuts per bolt for

ultra hold.

3. To avoid possible water

ingress into wire harness

area, route the harness in

the downward direction

as shown above.

Instructions:

1. Install jamb nuts (4) loosely on mounting

studs (3), so they will not touch mounting

brackets (5) when installed.

2. Slip mounting bracket (5) on and make

flush with mounting surface (2).

DO NOT RIGHTEN

3. Snug spring washer (6) and outer nuts (7)

against mounting plate (2).

DO NOT TIGHTEN

4. Position jamb nuts approximately 1/16”

from mounting bracket.

5. Tighten outer nuts completely.

AUX Section Operation

1. To Select USB mode

At Home Menu, press TUNE Up or Down to move the highlight to AUX source, then

press ENTER button to go into the AUX mode.

Note: highlight movement indicated by the icon background change.

The use of auxiliary mode allows you to play

the portable music device through the

headphone jack.

Note: An additional accessory/adaptor must be

purchased in order for this to happen.

Prospec's part, SEAMINI2 or

SEAUSBMINI36 fulfills this option.

Wire Configuration

12P CONNECTOR

(REM)

( ACC )

( GROUND )

FUSE

BLUE

RED

BLACK

GRAY

GRAY/BLACK

VIOLET

VIOLET/BLACK

(FRONT RIGHT )

( REAR RIGHT )

GREEN

GREEN/BLACK

WHITE

WHITE/BLACK

( FRONT LEFT )

( REAR LEFT )

(USB)

RED

WHITE

(AUX)

(ANT JACK)

RED

WHITE

(REAR LINE OUT)

(SiriusXM)

RED

WHITE

(SUBWOOFER)

6P REMOTE

CONTROL

RED

WHITE

(FRONT LINE OUT)

(CAN BUS)

NOTE:

1. When wiring, the red lead is recommended to be wired to ACC/ignition power lead.

2. Make sure that the black wire on the wiring harness is connected to a good ground point

on the boat. If the chassis f the boat is used as a ground point, make sure that the surface

is scraped clean of paint before attaching the wire to it. It is recommended to connect the

black ground wire directly to negative terminal (-) of the boat battery.

3. Before wiring your system, disconnect your boat battery’s positive (+) cable. This helps

prevent damage in case of a short.

注：切边后的成品尺寸一定为 145x210mm

对折基准线

1. Connect

Connect an iPod/iPhone to the USB socket, it will read the files automatically. The track

information displays on the screen once playback starts.

2. Play/Pause Play

While iPod/iPhone playing, simply press the PAUSE button to pause the playback, and

press it again to resume playback.

3. Track Up/Down

While iPod/iPhone playing, simply press TUNE Up or Down button to select the next or

previous track.

3. Track Repeat play

While iPod/iPhone playing, simply press MENU button to activate navigation, it will

highlight at RPT, then press MENU button to toggle select Track Repeat or RPT OFF.

(Note: Refers to play current track repeatedly.)

4. Random play

While iPod/iPhone playing, simply press MENU button to activate navigation, then press

TUNE Down button to move highlight to RDM, then press MENU button to toggle

select Track Random or RDM OFF.

(Note: Refers to play all the tracks in a random sequence.)

iPod/iPhone Operation

Only display when EQ / LOUD ON

was selected in the Settings.

ID3 tag:

Song name

Artist

Album

Play/Pause

RPT: Track Repeat play

RDM: Track Random play

Track No.

Track elapse time

Play mode

Note: refers to PLAY; refers to PAUSE.

Note: Please make sure the iPod/iPhone cable is connected correctly.

And it is recommended to use the original cable for connection.

General Function of Buttons

ENTER

1. POWER, MUTE, PAUSE button

- With unit off, press to power the unit on.

- With the unit on, press and hold for over 2s to power the unit off.

- In Radio, SiriusXM, AUX mode, press to MUTE sound output,

press again to resume sound output.

- In USB, BT Music mode, press to PAUSE playback, press again

to resume playback.

2. MENU, ENTER button

- In any status, press and hold for 2s to navigate to home display.

- In source playing status, quick press to activate the bottom navigation function.

(Note: Bottom navigation function is disabled after 5s without operation.)

- In any selection status, press ENTER to confirm selection.

3. VOLUME Up button

- Simply press it to increase volume level.

4. VOLUME Down button

- Simply press it to decrease volume level.

5. Tune Up button

- In playing status, press to select the next station, channel, or track.

- In bottom navigation mode, press to move highlight upward/over.

6. Tune Down button

- In playing status, press to select the previous station, channel, or track.

- In bottom navigation mode, press to move highlight downward/over.

4. Track Up/Down

While USB playing, simply press TUNE Up or Down button to select the next or previous

track. To fast forward or rewind, press and hold TUNE button.

5. Scan Play

While USB playing, simply press MENU button to activate navigation, it will highlight

at SCAN, now repeat press MENU button to toggle select Track Scan, Directory Scan, or

SCAN OFF. (Note: The play mode icon would change simultaneously.)

6. Repeat play

While USB playing, simply press MENU button to activate navigation, then press TUNE

Down button to move highlight to RPT, repeat press MENU button to toggle select Track

Repeat, Directory Repeat, or RPT OFF. (Note: The play mode icon would change

simultaneously.)

7. Random play

While USB playing, simply press MENU button to activate navigation, then press TUNE

Down button to move highlight to RDM, repeat press MENU button to toggle select

Track Random, Directory Random, or RDM OFF. (Note: The play mode icon would

change simultaneously.)

8. F.LIST (Folder / File Search)

While USB playing, simply press MENU button to

activate navigation, then press TUNE Down button

to move highlight to F.LIST, press ENTER button

to go inside the F.List.

In F.List, press TUNE Up or Down button to choose

desired Folder, press ENTER to display sub-directory

or files inside, press TUNE Up or Down button to

choose desired file and press ENTER button to play it.

Refers toplay current track repeatedly.

Refers to play the tracks in current Directory repeatedly.

Refers to play all the tracks in normal sequence.

Refers to play all the tracks in a random sequence.

Refers to play the tracks in current Directory in a random sequence.

Refers to play all the tracks in normal sequence.

USB Section Operation

Refers to play the first 10s of all the tracks in the USB device.

Refers to play the first 10s of all the tracks in current Directory.

Refers to play all the tracks in normal sequence.

2. Home Menu (Source display)

At Home Menu, press the TUNE Up/Down button to move to desired source and press

ENTER button to confirm.

Radio SiriusXM BT Music

USB AUX IN Settings

1. Sign Up Display

Once the unit powered on, the introductory home screen appears for 4 seconds, then

switches to the last played mode before power off occurred.

Push

Note: icon background changes to two toned burnt orange

when selected. For example, Radio mode is the selected

mode in above picture.

注：切边后的成品尺寸一定为 145x210mm

对折基准线

USB Section Operation

1. To Select USB mode

At Home Menu, press TUNE button to move the highlight to USB source, then press

ENTER button to go into the USB mode.

Note: This input is dsigned to read and play USB drives (mp3 and wam files), not media/

phones.

You can charge most phones through the USB input. Music, however, needs to be

played back by using eigher BT or Aux input.

2. USB Screen Description

3. Play/Pause Play

While USB is playing, press the PAUSE button to pause the playback, and press

again to resume playback.

Only displays when EQ / LOUD ON

was selected in the Settings.

ID3 tag:

Song name

Artist

Album

Play/Pause

SCAN: Intro Scan play (Track / Directory Scan play)

RPT: Repeat play (Track / Directory Repeat play)

F.List: To display the Directory / File List

RDM: Random play (Track / Directory Random play)

Track No.

Track elapse time

Play mode

Note: refers to PLAY; refers to PAUSE.

General Operations

1. VOLUME Control

2. MUTE Control

In Radio, SiriusXM, or AUX mode, press

MUTE button to mute sound output; press

again to resume sound output.

In any mode, press VOL UP/DN button to

adjust volume level.

Press and hold VOL button to adjust volume

level rapidly.

3. General Settings

Press and hold MENU button to go back to

Home Menu, then press TUNE UP/DN button

to move highlight to Settings source. Then

press ENTER button to go into the Settings

mode.

3-1. Bass Control

In Settings screen, press TUNE Up or Down button

to select Bass, then press VOL Up or Down button

to adjust Bass level.

3-2. Treble Control

In Settings screen, press TUNE Up or Down button

to select Treble, then press VOL Up or Down button

to adjust Treble level.

对折基准线

4. Play/Pause Play

Once the BT device being paired is successful, music will begin to play.

Note: For some Bluetooth enabled phones, you might activate play from your phone first.

It depends on the phone itself.

While BT Music playing,

Note: With the Bluetooth connection disconnected, once you power on the unit next time,

it will establish the Bluetooth connection automatically.

press the PAUSE button to pause the playback, and press it

again to resume playback.

5. Track Up/Down

While BT Music is playing, press TUNE Up or Down button to select the next or

previous track.

6. Disconnect

In BT Music playing mode, in order to disconnect the BT device, press MENU button

to activate bottom navigation, it will highlight at DISCONN, press ENTER button to

disconnect the BT connection.

Note: When your BT device battery is at low charge, the Bluetooth connection may

occasionally be lost. To maintain good connectivity ensure that your BT device battery

is adequately charged.

7. Connect

With BT device paired OK, but disconnected, if you want to reestablish the BT connection,

press MENU button to activate bottom navigation, it will highlight at CONNE. Press

ENTER button to connect the BT device.

Note: refers to PLAY; refers to PAUSE.

Bluetooth Section Operation

3-3. Balance Control

In Settings screen, press TUNE Up or Down button

to select Balance, then press VOL Up or Down button

to adjust Balance level.

3-4. Fader Control

In Settings screen, press TUNE Up or Down button

to select Fader, then press VOL Up or Down button

to adjust Fader level.

3-5. Loud Control

In Settings screen, press TUNE Up or Down button to

select Loud, then press VOL Up or Down button to

select ON or OFF.

3-6. EQ Selection

In Settings screen, press TUNE Up or Down button to

select EQ, then press VOL Up or Down button to select

Off, Classics, Jazz, Pop or Rock.

3-7. Subwoofer Gain Control

At Setting screen, press TUNE Up or Down button to

select Subwoffer, then press VOL Up or Down button

o adjust Subwoofer Gain level.

3-8. I-Volume Control

At Setting screen, press TUNE Up or Down button to

select I-Volume, then press VOL Up or Down button

to adjust the Initial Volume Level. This feature controls

the maximum volume level desired when powered on.

General Settings

Bluetooth Section Operation

1. To Select Bluetooth mode

At Home Menu, press TUNE button to move the highlight to Bluetooth source, then simply

press ENTER button to go into the Bluetooth mode.

Note: highlight movement indicated by the icon background change.

2. Bluetooth Screen Description

3. Pair BT Device

If there is no BT device paired, go to settings on the BT device and turn the Bluetooth

option ON. Pick “PRV” option on your Bluetooth enabled device.

(if you are prompted for a password, the code entered will be “1234”.)

If there was previously a BT device paired, simply press MENU button to highlight

CONN and press ENTER to establish the BT connection.

Only displays when EQ / LOUD ON

was selected in the Settings.

ID3 tag:

Song name

Artist

Album

Play/Pause

CONN: To establish Bluetooth connection.

DISCON: To disconnect the BT Device.

BT icon

If already has BT device

connected, here display

DISCON.

If no BT device connect,

here display CONN.

Paired device name.

3-9. Brightness Adjustment

In Settings screen, press TUNE Up or Down button to

select Brightness, then press VOL Up or Down button

to adjust Brightness level.

3-10. Area Selection

In Settings screen, press TUNE Up or Down button to

select Area, then press VOL Up or Down button to

select USA or EUR.

3-11. SiriusXM Parental Lock - Change Code

In Settings screen, press TUNE Up or Down button to

select Parental Lock. Then press VOL Up or Down

button to select Parental Lock sub-features.

Please refer to SiriusXM Section Operation for details.

3-12. SXM Reset

At Setting screen, press TUNE Up or Down button to

select SXM Reset, then ENTER button to reset the

SXM Tuner.

3-13. Software Version View, Software Reset

At Setting screen, press TUNE Up or Down button to

select S/W Version, then press MENU button to active

highlight at VIEW and press ENTER button to view

the Software Version.

Software Reset:

In Software Version display status, press TUNE UP,

TUNE DN, and TUNE UP in sequence, then press

and hold TUNE DN for 7s to reset the unit.

Note: It will be necessary to re-enter the radio preset

memories and other personal settings as these

will have been erased when the software was

reset. After resetting the unit, ensure all

functions are operating correctly.

General Settings

Other Prospec Stereo Receiver manuals

Prospec

Prospec PRV17 User manual

Popular Stereo Receiver manuals by other brands

Marantz

Marantz CINEMA 70S owner's manual

Kenwood

Kenwood KMDX92 instruction manual

Yamaha

Yamaha RX-830 owner's manual

Pioneer

Pioneer AVH-Z7250BT owner's manual

Yamaha

Yamaha RX-750 owner's manual

Denon

Denon AVR-1311 owner's manual

Denon

Denon AVR-S760H owner's manual

Denon

Denon AVR-X7200W Service manual

Pioneer

Pioneer SC-LX904 Initial setup guide

Sony

Sony XAV-1500 operating instructions

Radio Shack

Radio Shack DX-399 owner's manual

Sony

Sony STR-DE535 - Fm Stereo/fm-am Receiver operating instructions

Pioneer

Pioneer SX-1000TA operating instructions

Yamaha

Yamaha MusicCast TSR-5B3D owner's manual

Sony

Sony STR-DE335 - Fm Stereo/fm-am Receiver operating instructions

Sony

Sony STR-DG500 - Multi Channel Av Receiver Service manual

Panasonic

Panasonic AJSD955B - DVCPRO50 STUDIO DECK Brochure & specs

Pioneer

Pioneer SX-838 Service manual