ProofVision 24 inch Waterproof TV User manual
LED
ProofVision
“Making it work in challenging conditions”
ProofVision
“Making it work in challenging conditions”
INSTALLATION MANUAL
It is the installer's responsibility to ensure that your waterproof LED TV is installed and sealed
correctly. Your warranty becomes void if problems occur due to faulty installation or poor
sealing.
1. Decide on the correct position for your TV. Test the TV in that position to make sure the
viewing angle is appropriate for the viewing position. Each waterproof TV model has specic
viewing angles. Position the front bezel in order to view the picture clearly from all intended
areas. Should there be any doubt, make the area safe and power up the LED, positioning the
screen until satised that the picture does not darken or disappear from view as close to eye
level as possible.
2. Once you have your position check for any hazards that may stop you installing in this area,
i.e. cables or pipes. When mounting in stud walls, check for any supporting framework behind
the plasterboard.
3. Use the table below to work out the cut out size within the wall to t the TV. The recess in
the wall should be the cut to the size of the mounting plate dimensions.
4. Open up the cable cover by unscrewing all 8 screws, connect the power cable and the aerial
(RF cable) and also any other desired cables. Place the cable cover back, in line with the holes
and screw it back into place, making sure that it is secure and tight. Chase all cables into the
wall at the bottom of the TV to reduce chances of water reaching the TV.
5. When all the material is removed within the dimensions detailed to suit your size of the TV.
Use the screws provided to x the mounting case in place. Make sure the edges of the
mounting case are directly in line with the wall or tiles. Also make sure the mounting case is
securely tted as this supports your TV unit.
6. Now the TV is connected check that all the functions of the TV are working before tting.
The signal level feed to the TV must be at least 65db/1 mill volt or the picture may be noisy or
pixelated and dicult to tune. A distribution amplier may be required if you are in a weak
signal area. If in doubt, consult a qualied aerial technician.
7. Apply a continuous unbroken bead of clear waterproof silicon around the inside of the
television bezel at least 5mm thick. Use clear, mould resistant waterproof bathroom sealant.
All models do not require any ventilation considerations.
8. Oer the television to the wall cut out and place the TV into the back plate, push the TV
ProofVision
“Making it work in challenging conditions”
ProofVision
A
B
C
D
EG
H
F
Front Side Back
down to lock the TV into the back plate lugs. Wipe away all excess silicon from the outside of
the bezel using a damp soft lint free cloth. Allow 24hrs to dry before use.
9. It is critical the bezel is rmly sealed to the wall surface to complete the waterproof
properties of the installation. Failure to properly seal the TV may result in water leaking behind
the screen and wall surface, which could result in damage to either the TV or wall. Damage
caused to the television in this way is not covered by warranty.
10. If you would like to add in external ceiling speakers, We recommend the ProofVision Elite
Music System (PV48-BT) which is powered by a mains supply or the ProofVision Bathroom
Bluetooth Music system( PV26-BT) which is powered by hard wire connection. To connect the
ProofVision Elite Music System (PV48-BT) or the ProofVision Bathroom Bluetooth Music
system( PV26-BT) you would run a RCA cable from the speakers to the Audio out (3.5mm jack)
which is located at the back of the ProofVision bathroom TV, when doing this it will disable the
built in speakers and only play from the ceiling speakers. If you already have ceiling speakers in
the bathroom and want to connect those speakers to the ProofVision bathroom TV you would
require an amplier which allows you to connect speaker cables to the amplier and also have
an audio in port allowing you to use a 3.5mm AUX cable. When using the external amplier
you would also need a mains power supply to power the amplier.
A
490
595
777
995
1320
B
335
397
506
630
825
C
3
3
3
3
13
D
450
510
700
935
1210
E
238
285
395
525
685
F
474
580
760
984
1281
G
318
380
496
619
796
H
48
45
61
61
50
Front frame (mm) Back mounting box (mm)
Size
19”
24“
32”
42”
55”
ProofVision
“Making it work in challenging conditions”
IMPORTANT SAFETY INFORMATION
1. Do not attempt to remove the back of this TV; this can expose you to high voltage and risk of
electric shock or re.
2. Do not attempt to modify this product in any way as this will invalidate your warranty and
expose the risk of electric shock or re.
3. Only use the supplied AC DC transformer and ensure the main power cord is plugged into a
non
damaged socket and away from any heat source. The power supply is not waterproof and must
be
positioned in a dry, well ventilated area away from water and moisture.
4. Do not connect the TV direct to the mains socket without converter.
5. Position your TV so that no bright light, sunshine or direct heat can aect the TV.
6. If there are any unusual smells or sounds coming from the unit, disconnect the power and
contact your supplier.
7. The unit must be earthed to the main earth system of the building and must conform to the
latest electrical safety regulations.
8. When cleaning your TV do not apply any abrasive cleaners, wax, benzene, alcohol or
cleaning
detergents. Chemical cleaners may fade dissolve or crack the TV surface. We recommend a soft
damp cloth and non abrasive cleaner.
Please note that the installation of your TV should be carried out by a technically competent
person and must conform to all the relevant regulations. If in doubt please contact ProofVision
or a qualied electrician.
ProofVision
“Making it work in challenging conditions”
LED
LED
LED
LED
LED
LED
ProofVision
“Making it work in challenging conditions”
ProofVision
“Making it work in challenging conditions”
(Use CR2032 battery)
Note: the oered remote control is qualied as splash proof
3. Replace the back cover of the remote control with the opener by going round
until you hear a click sound.
ProofVision
“Making it work in challenging conditions”
x 2
6. USB
7. Audio out
8. Component
x2
When the TV is on, the front light will be blue, and will be red when the TV is o.
ProofVision
“Making it work in challenging conditions”
ProofVision
“Making it work in challenging conditions”
Not applicable to this product
This manual suits for next models
4
Table of contents
Other ProofVision TV manuals
