Pro8mm MAX 8 User manual

1
Pro8mm
2805 W. Magnolia Blvd, CA 91505
Ph:(818)848-5522 Fax:(818)848-5956
www.Pro8mm.com

2
INSTRUCTIONS FOR USE
Table of Contents
PAGE #
1. Table of Contents
2. Table of Contents Cont.
3.
a. Introduction to Max 8
b. C-cell power pouch specifications
c. C-cell power pouch charging instructions for trickle charger
4.
a. Lens specs and packages available
b. Mounting the lens
5. “Getting familiar with the Classic Camera”
a. Master Switch <Classic Only>
b. Release button (Trigger) & cable-release socket
c. Emulsion-speed selector
d. Filming-speed selector
6.
a. Footage counter
b. Ground-glass focusing knob
c. Remote control release socket (electronic)
d. Remote control release socket (mechanical)
7.
a. Crystal speed module
b. Single-frame release socket
c. Shutter lever
8.
a. Viewfinder
b. Eyepiece focusing ring
c. Adjusting the eyepiece (alternate methods)
d. Loading the Film
e. Battery Check <Classic Only>

3
9.
a. Setting the emulsion speed values
b. Setting the run speed (fps)
c. Table of exposure times
10.
a. Exposure control
1. Automatic mode
2. Semi-automatic mode
3. Manual Control mode <Classic Only>
b. Filters
11.
a. Remote control
b. Focusing (best method)
12.
a. Exposed film
b. Special Effects
13.
a. Metaspeed film to video transfer
b. Camera Care
14. Pro8mm support
15. Special Instructions for Max8

4
PRO8MM MAX 8 PROFESSIONAL CAMERA
with CRYSTAL SYNC
3a. INTRODUCTION TO MAX 8
The Max 8 Modification to the Classic Professional camera expands the
frame size on the super 8 film master. The viewfinder on the camera has
the 16 x 9 frame marked for better framing during production. This
gives filmmakers the ability to work in a ratio, which is more compatible
with High Definition & Enhanced for Widescreen DVD Mastering and
Academy 35mm. The new expanded frame gives a 20% increase in
usable picture when framing for 1.78.
Max 8 is compatible with all existing Pro8mm and Super 8mm film
stocks. The modification to the camera does not interfere with the ability
to shoot a traditional 4 x 3 frame. The ground glass has 1:78 frame lines
to guide the cinematographer as well as the full 4 x 3 frame. Max 8
negative uses a ratio of 1:58, whereas traditional 8mm film uses a frame
ration of 1:33.
The Y-Front URSA Diamond flying spot scanner at Pro8mm has been
custom modified to MAX8 1:58 scanning of Super8 so that the highest
quality widescreen format transfer can be achieved. Max 8 is unique to
Pro8mm and can only be accomplished with the Pro8mm Max 8 Camera
and Pro8mm Max8 Digital Mastering.
b. C-CELL POWER POUCH SPECIFICATIONS
Pro8mm provides the discriminating cinematographer with the longest
lasting battery pack. Our Ni-Cad 2400 milliamp battery pack will run
approximately 50 rolls of film on a full charge, compared to the 250
milliamp battery (5 rolls of film) of yesteryear.
Note: Batteries will come with a full charge of power.
c. C-CELL POWER POUCH CHARGING INSTRUCTIONS
1) Plug the trickle charger into wall socket
2) Plug the battery into charger
3) Battery should be completely charged after 5 hours

5
4a. LENS SPECS AND PACKAGES AVAILABLE
8-64mm manual zoom:
F 1.9 to 22, focus range from 3’ to infinity. Filter size is 49mm.
This lens is included in the rental package.
8-64mm manual zoom with Macro:
F 1.9 to 22, focus range from 3’ to infinity. Includes back-focus shift
macro. Filter size is 49mm.
This lens is not included with the rental package, but can be for an
additional charge.
8-64mm power zoom with Macro:
Power zoom and power exposure. F 1.9 to 22, focus range from 3’ to
infinity. Includes back-focus shift macro. Filter size is 49mm.
This lens is not included with the rental package, but can be for an
additional charge.
.5X Ultra Wide Adapter:
Accessory adapter for the 8-64 lens system to adapt to 4-32mm focal
length.
b. MOUNTING THE LENS
Pro8mm zoom lenses fitted with lens control units may be used in
addition to standard “C” mount lenses. A variety of other lenses may be
used with an appropriate “C” mount adapter.
Power lens:
To mount the lens, unscrew the camera-protecting cap, and then the
trigger button. (Make sure to unscrew the camera’s trigger before
mounting the lens)
C-mount & Manual lens:
These lenses can be mounted directly by aligning the threads, then
turning the lens clockwise until it is tight. Make sure to not over-tighten
the lens to the camera.
35mm lens:
When using a still camera lens, fit the adapter ring to the camera first,
and then mount the lens.

6
“Getting familiar with the Classic Camera”
5a. MASTER SWITCH <For Classic ONLY! Removed in Crystal Sync
models
This switch has three positions: “Auto”, “Manual”, and
“Test”. These three positions correspond to the following
uses: (This switch is removed in crystal sync. modified
cameras)
“Auto”
This position is to be used if the camera is fitted with a Pro8mm power
lens.
“Manual”
To be used when it is desired to uncouple the automatic diaphragm
control, and then set the exposure manually.
“Test”
This position is used for checking battery charge.
5b. RELEASE BUTTON (TRIGGER) & CABLE-RELEASE SOCKET
This button has three positions:
1) “Free”: the film does not advance.
2) “Depressed”: this position puts the film in
motion
3) “Depressed and turned 90 degrees
clockwise”: this position locks the release
button and allows continuous filming. The
female thread in the center of the button
receives the cable release.
4) WARNING!! The ELECTRICAL remote release trigger must be
used when shooting over 24fps or the camera motor will burn
out!

7
5c. EMULSION-SPEED SELECTOR
This dial allows you to select the ASA/ISO setting for the internal
exposure meter. Note: The 400 ASA setting should be used for 500 ASA
films.
5d. FILMING-SPEED SELECTOR
This dial makes it possible to set the camera at the desired filming speed
between 2 and 70 fps. If your Classic Camera is equipped with a power
lens, the camera will automatically correct the diaphragm for proper
exposure according to the shutter speed selected. This makes it possible
to change run speeds during filming. (It is also possible to change filming
speeds with a “manual” lens, but the exposure will have to be calculated
separately.)
5) WARNING!! As stated earlier, The ELECTRICAL remote release
trigger must be used when shooting over 24fps or the camera
motor will burn out!
6) WARNING!! Because the exposure indicator is tied to the film
speed selector, if you have the crystal sync set at 24fps but
have the speed selector set at a different speed ,i.e. 2fps,
then the exposure indicator will expose for 2 fps, not 24fps
like you wanted. Make sure that if you are shooting crystal
sync that the film-speed indicator is set for 24fps.

8
6a. FOOTAGE COUNTER
This indicates the footage still available, both in frames and in feet. The
counter automatically resets to zero when the film is unloaded.
6b. GROUND-GLASS FOCUSING KNOB
This makes it possible to interpose or to retract a ground glass screen
between the eye and the lens. The advantage of the screen is that it gives
the operator an accurate appreciation of focus and the depth of focus
available with the aperture used. The knob located to the left of the frame
counter can retract the ground glass. Use the ground glass when
shooting with a low f-stop for fine focus situations and pull the ground
glass away when shooting with a high f-stop for a clearer view. Note: The
gritty view of the ground glass does not expose on film.

9
6c. REMOTE CONTROL RELEASE SOCKET (ELECTRONIC)
Located to right (right-rear) of the viewfinder, this socket takes a special
electronic remote control lead plug, which is included in all rental
packages. You must use this remote release cable in the socket for any
frame rate above 24, (slow-motion).
•When using the remote, the shutter will not always
stop in the closed position. This will sometimes block
the viewfinder. This soft stop protects the mechanism
stop pin and the motor. If viewfinder is blocked: turn
remote on and off real fast, this should reset the finder
so you can see.
6d. REMOTE CONTROL RELASE SOCKET (MECHANICAL)
Located inside the trigger, this socket is used in conjunction with any
standard deep-throated threaded cable release.

10
7a. CRYSTAL SPEED MODULE (accessory)
The crystal speed module is located below the eyepiece. It will govern the
camera’s running speed assuring a constant speed, allowing sound to be
recorded on a separate sound recorder. You may switch to variable
speeds: 2 – 70 fps or sync 24 fps.
When the camera is switched over to sync 24 fps the red light above and
to the right of the sync switch will flicker brightly and constantly. When
the camera is shooting at variable speeds the light will fade in and out
and the flickering of the light will not look constant. This light can also
be a warning if the camera is out of sync. If the light fades in and out
even in sync 24 than the camera is not in sync.
Even if one is not shooting sync sound, leaving the camera in sync 24
mode will maintain constant exposure because there is no chance of
speed change and therefore no chance of exposure drops and increases.
It will also eliminate strobing effects if shooting with HMI lights.
7b. SINGLE-FRAME RELEASE SOCKET
<Function NOT set up for in basic camera package : Must be set up>
Single-frame filming can be achieved with a flexible release plunger
screwed into this socket, located below the film-loading door. The
Beaulieu custom plunger release is required. <Using the wrong remote
will fry the camera motor> This can be set up for $200. (Use extreme
caution when using this feature. If plunger cable fails to retract it
could possibly “fry” camera motor!)
Table of contents

















