Pro-Ject Audio Systems VC-S Firmware update

INSTRUCTIONS FOR USE

Pro-Ject VC-S

Controls, features and connections

1 Vacuum arm* (adhesive velvet strips attached)

2 Clamp (rear part)*

3 Fixing screw for clamp*

4 Ventilation outlet hole

5 Main switch with mains inlet socket

6 Vacuum rocker switch

7 Motor rocker switch

8 Vinyl record

9 Clamp (top part)*

10 Ball knob*

11 Spindle

Accessories (delivered, but not shown above)

1 Wash it vinyl cleaning concentrate (100ml bottle)

2 Goat hair brush

3 Adhesive strips for vacuum arm (replacement)

4 Spout (drain insert)

5 Mains connection cable

Optional accessories (available on request)

Wash it vinyl cleaning concentrate

bottle sizes: 100ml/250ml/500ml/1l (100ml ≙150 records / both sides)

Wash it 78 shellac cleaner concentrate (without alcohol)

bottle sizes: 250ml/ 1l (100ml ≙150 records / both sides),

Goat hair brush

Adhesive strips for vacuum arm

Cover it VC-S (lid with hinges and mounting screws)

Dear music lover,

Thank you for purchasing a Pro-Ject Audio Systems record cleaning machine.

In order to achieve maximum performance and reliability, please study these instructions carefully.

Warning of a hazard for the user, the unit or possible misuse

Important notice

During assembling and adjustment small parts could be lost if they are not carefully placed in a suitable

receptacle. Before starting assembly make yourself acquainted with the parts listed above which are

correspondingly numbered in the technical drawings. Separately packed items are marked with an asterisk *.

Safety instructions

AC outlet voltages vary from country to country. Before connecting to the mains, make sure that the

voltage in your area meets the voltage requirements printed on the device.

Hold the plug when unplugging the power cord. Never handle the power cord while your hands are

wet or damp.

Never place any naked flame sources, like lighted candles, on or near the device. The product shall

not be used in damp or wet locations, next to a bathtub, sink, swimming pool or any other similar

conditions.

Keep plastic bags away from children to prevent any risk of suffocation.

Do not cover any ventilation holes (one is located on the left side and others are on bottom).

Setting up the unit

The unit is supplied assembled except of platter and vacuum arm which are packed separately. Remove all

parts from the transport packaging carefully. Please see the picture above that shows how to assemble the unit

(screwdriver is required).

Preparation of Wash it vinyl cleaning fluid

The cleaning concentrate should be diluted before application:

Mix 1 part of Wash it concentrate with 5 parts of distilled / demineralized water!

Caution! The vinyl cleaning concentrate is only suitable for vinyl records. 78rpm shellac records are

sensitve to some cleaning agents, please only use special Wash it 78 cleaning fluid!

Preparation of Wash it 78 shellac cleaning fluid

The cleaning concentrate should be diluted before application:

Please follow instructions delivered with Wash it 78

Using the unit

Make sure the unit is fully set up following the article above in this manual. All 3 rocker switches ("main

switch", "motor" and "vacuum" should be in position "0"). Connect the power cord to the socket on the back

side and turn the main switch to the position "I".

Place a record on the rear part of the clamp, put the top part of the clamp on it and screw it all together with

the ball knob by using a moderate force. Do not over-tighten. If the force is too low, the record will not turn

even if the motor runs.

Apply a few drops of cleaning fluid and spread it over the surface of a record using the supplied brush. The

fluid should be evenly spread out over the entire surface. Use only the necessary amount of fluid, just to

cover the record, not the machine!

The record label is protected by the clamp. The motor can turn both directions or can be stopped during the

application of the fluid, depending on your personal preferences. For better dissolving of impurities, wait a

few seconds before starting the vacuuming process. Place the vacuum arm above the record pointing at the

spindle until it reaches its lock position.Turn the motor rocker switch into position "I" for rotating clockwise or

to position “II” for counter-clockwise rotation and then turn on the vacuum rocker switch. Usually one

revolution of the record is needed for full fluid removal.

Switch off vacuum first and then the motor. Return the vacuum arm into its rest position and wait a few

seconds. Unscrew the ball knob, remove the clamp, turn the record over and repeat the steps for the

opposite side of the record.

The unit is protected by an automatic overheating protection, which switches the motor off in case of

excessive usage. After a cool-down period, the unit returns to full usability!

Maintenance and cleaning

Your record cleaning machine requires little or no regular maintenance.

On the left side of the unit below the air outlet hole is a water level gauge. The tank inside has big capacity

and it usually takes long time to fill the tank. Certain amount of cleaning fluid is also evaporized. In case of

the water level reaching the point marked " ←MAX" the tank should be discharged:

1. remove the plastic from the ventilation outlet hole (4)

2. place the spout into the hole (this drain insert is supplied in the accessory box)

3. lift the opposite side of the unit up end empty the unit reservoir

Regularly check the velvet strips on the arm. Make sure they are clean, no dirt or debris is present.

Always disconnect the record cleaning machine from the mains power supply as a precaution before

maintenance!

Fitting the lid (Cover it VC-S is an optional accessory)

The holes for lid hinges are pre-drilled on the back side of the unit. Each hinge is screwed with 2 screws

(supplied with the lid).

Fit the lid carefully over the hinge prongs and adjust the screws until the lid stays open where you want it to

without being too stiff to open or close.

Technical specifications Vinyl Cleaner VC-S

Nominal speed

30 r.p.m.

Power consumption

230V/800W, 120V/1300W

Dimensions (W x D x H)

435 x 335 x 280 mm (fully assembled)

Weight

10,5kg (netto)

Fuse 230V/120V

T5A/T6A

Potential incorrect use and fault conditions

Pro-Ject products are manufactured to the highest standards and undergo strict quality controls before

leaving the factory. Faults that may possibly occur are not necessarily due to material or production faults but

can sometimes be caused by incorrect use or unfortunate circumstances. Therefore the following list of common

fault symptoms is included.

The platter doesn't turn although the unit is switched on:

The unit is not connected to the mains power supply.

No mains at the socket.

Broken fuse in the main switch.

Overheating protection is active.

Ball knob is not well-tightened.

Service

Should you encounter a problem which you are not able to alleviate or identify despite the above information,

please contact your dealer for further advice. Only when the problem cannot be resolved there should the

unit be sent to the responsible distributor in your country.

Guarantee repairs will only be affected if the unit is returned correctly packaged. For this reason we recommend

keeping the original packaging.

Never return a record cleaning machine without making sure that is it safely disassembled and correctly

packaged in the original packaging.

Warranty

The manufacturer accepts no responsibility for damage caused by not adhering to these instructions

for use and/or by transportation without the original packaging. Modification or change to any part

of the product by unauthorized persons, release the manufacturer from any liability over and above

the lawful rights of the customer.

Pro-Ject Audio Systems is a Registered Trademark of

H. Lichtenegger.

This guide was produced by: Pro-Ject Audio Systems

The information was correct at the time of going to

press. The manufacturer reserves the right to make

changes to the technical specification without prior

notice as deemed necessary to uphold the ongoing

process of technical development.

Table of contents

Other Pro-Ject Audio Systems Turntable manuals

Pro-Ject Audio Systems

Pro-Ject Audio Systems Primary User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Essential II User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems SIGNATURE 10 User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems X8 User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject RPM 3 Carbon User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems 2 Xperience Basic + User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems VT-E BT L User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems 2 Xperience Basic + User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Align it User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Essential User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems VTA it User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Essential II/Phono USB User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems T1 Phono SB User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems RPM 1.3 Genie User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems A2 User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems RPM 5.1 User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Essential User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Xtensions 9 S-Shape User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems THE CLASSIC User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems 1 Xpression Classic User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject 1 Xpression III User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Perspective Final Edition User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems RPM 5.1 User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Jukebox E User manual

Popular Turntable manuals by other brands

Gemini

Gemini CDT-05 MKII product manual

Rotel

Rotel RP-820 owner's manual

Shuman

Shuman MC-250BT user manual

Stanton

Stanton STR8-150 owner's manual

Audio Technica

Audio Technica AT-LPW40WN user manual

Crosley

Crosley McQueen CR7011-GY instruction manual

Reloop

Reloop SMP-1 Operation manual

auna

auna TT-Classic Plus instruction manual

COMO AUDIO

COMO AUDIO Turntable Analog user manual

Dual

Dual 1009 F owner's manual

REED

REED Muse3C user manual

AXIOMTEK

AXIOMTEK OPS883-H Series Quick installation guide

Pioneer

Pioneer PL-71 operating instructions

Vestax

Vestax PDX-a1 owner's manual

Denon

Denon DP-400 owner's manual

Dual

Dual 504 Service manual

Audio-Techica

Audio-Techica AT-LP60XBT user manual

Goldring

Goldring G99 instruction manual