Pro-Ject Audio Systems Remote Box S2 User manual

INSTRUCTIONS FOR USE

Pro-Ject MaiA S2

Dear music lover,

thank you for purchasing a Pro-Ject Audio Systems´ amplifier.

In order to achieve maximum performance and reliability you should study these instructions for use carefully.

Warning of a hazard for the user, the unit or possible misuse.

Important notice.

Safety instructions

AC outlet voltages vary from country to country. Before connecting to the mains, make sure that the

voltage in your area meets the voltage requirements printed on the power supply.

The power supply is used to connect/disconnect the unit from the mains. Make sure that the power supply

is easily accessible at all times. Never handle the device, the power supply while your hands are wet or

damp. Avoid letting liquids enter the device or the power supply. Never place any item containing

liquid, such as a flower vase on or near the device. Never spill any liquid on the device or the power

supply. Never place any naked flame sources, such as lighted candles on or near the device. The product

shall not be used in damp or wet locations, next to a bathtub, sink, swimming pool or any other similar

conditions.

Connectors

MaiA S2

1. Make all connections except the connection to the headphone and USB whilst the unit is

disconnected from the mains.

2.Never connect or disconnect power supply to or from the unit whilst the power supply is connected to

the mains !Never use any other power supply than the one supplied with the unit with the exception of

dedicated Power Boxes which can replace original power supplies.

3. Take care to connect the left and right channels of In1, In2, In3 correctly. The right channel is usually

marked red, the left channel black or white.

4. Maia only: Speaker connections for the left speaker are located on the right hand side of rear view

above, connections to right speaker are located near the power socket. Speaker connectors marked red

represent +according indicators on speaker terminal.

Line output

A power amplifier or active loudspeakers can be connected to the output sockets marked Output.

Connection to the speakers

The output terminals accept loudspeaker cables terminated with 4mm Banana plugs, spades connectors or

naked wire.

Phono input

Connect the tonearm signal lead to the In 1 Phono of the amplifier. The earthing wire may be connected to the

screw terminal if you encounter hum problems when using the turntable.

Line inputs

Line level sources such as CD player, radio or TV can be connected to the input sockets marked In 2, In3 or

In 4.

Digital inputs

Sources with a digital output such as TV satellite/cable receiver or a game console can be connected to the

digital inputs. Coaxial to In 5 and optical to In 6 and In 7.

Connecting to a Computer

Connect the USB-input In 8 USB of the MaiA (unit must be switched on) to a free USB-socket on your

computer and turn it on/make sure it is powered on. Select input 8USB.

Windows 10 and Mac OS®operating systems do not need an additional driver or setup.

Linux operating systems include an USB Audio Class 2 driver from Linux Kernel 2.6.35 and higher.

Please note: Connection should be made to an USB-socket of your computer directly. Connecting to

USB-hubs or switches can cause problems.

24Bit/192kHz playback with Windows® operating systems

* For older Windows®operating systems a 24Bit/192kHzUSB driver (supplied on CD) has to be installed.

Insert the included CD into the drive of you PC and follow the instructions.

After installing the driver, some settings have to be checked/done.

For example - Windows 7®operating system:

→Control Panel →Hardware and Sound →Sound→Playback:

select Speaker/MaiA USB 2.0 Audio Out

→Properties →Supported formats: make sure nothing is assigned

→Level →Sound: setting must be 100

→Enhancements: disable all enhancements →Advanced →Default Format: set to studio quality 24/192

Mains power connection

Connect the low voltage plug from the power supply to the Power socket before connecting the power supply

to the mains.

Front panel controls

To switch on from standby or to standby

The push button on the left side of the front panel turns the unit on or back into standby. The blue LED above

the stand-by push button shows that the unit is switched on. Mute is active when LED is blinking.

Input selector

After the unit is powered on, pressing the buttons◄ and ►next to the LEDs inputs indicators selects

desired input.

Volume

Adjust the volume to the desired level, using the large knob on the front panel.

Connecting a headphone

Connect the headphones to the ¼“ (6,3mm ) jack socket on the front of the unit.

BT connection

Make sure the antenna is attached to its connector In 9 BT on the back panel prior using BT

Use only supplied antenna

BT is active only when input 9 is selected. LED of BT input is blinking slowly when no device is connected. If

the LED is on, active connection with BT device is established.

Pairing with Android devices

Open Settings and tap on BT. Turn on BT and tap on Scan. Searched devices will show up. Tap on "MaiA

S2" and confirm presented pairing code on your Android device. Then press ►(pair) button on MaiA

(alternatively CH+ or VOL+ button on remote control) when the blue LED of input 9 starts blinking fast.

When paired with MaiA, your Android device will show "Connected to media Audio". Now you can play

music from your Android device over BT to MaiA S2.

Older devices may request a pairing code. Enter "0000" and confirm. No more confirmation on MaiA

is then needed.

BT pairing with Apple devices

Tap on Settings, tap on BT, turn on BT. Your device will automatically start searching for available devices.

Tap on "MaiA" and confirm by pressing ► (pair) button on MaiA(alternatively CH+ or VOL+ button on

remote control) when the blue LED of input 9 is blinking.

BT pairing with Windows smartphones

Open Settings and tap on BT. Turn on BT and a scan for available devices starts automatically. Searched

devices will show up. Tap on "MaiA S2" and confirm presented pairing code on your Windows device. Then

press►(pair) button on MaiA S2 (alternatively CH+ or VOL+ button on remote control) when the blue LED

of input 9 starts blinking fast. When paired with MaiA, your Windows device will show "Connected to media

Audio". Now you can play music from your Windows device over BT to MaiA S2.

MaiA S2 can store up to 8 BT devices. If the memory is full, new connections will automatically

replace the oldest connection. A new connection is only possible if the LED of BT input is blinking

slowly (it indicates that no device is connected).

Remote control

turns the unit on or back into standby (long press), mute (short)

and adjust the sound volume

and select the inputs

VOL+ and CH+ confirm BT pairing

VOL- and CH- cancel BT pairing

Replacing batteries

Proceed as follows:

•Unlock and slide open the battery case cover

•Replace the battery.

Make sure the battery is the right way round !

•Close the battery case cover

Battery type: 1 x CR2032 / 3V or 1 x CR2025 / 3V

Do not dispose the batteries as ordinary domestic refuse. Please dispose your exhausted batteries at

the appropriate collection sites - usually located at supermarkets and drugstores.

Technical specifications Pro-Ject MaiA S2

Power output : 2x 25W/38W at 8 ohms/4 ohms (5%THD)

Frequency response : 20Hz - 20kHz : -0,7dB, -0,5dB (@8ohms)

Channel separation : > 65dB at 20kHz

Noise floor : > -90dB (A weighted)

THD : < 0,07% at 15W

Gain : 33dB (measured via line level input)

Line level inputs : 2 pair RCA + 1 jack 3.5mm

Line input sensitivity : 350mV

Line input impedance : 50kohms

Phono input : 1 pair RCA

Phono input sensitivity : suitable for MM, MI or high output MC cartridges

Phono input impedance : 47kohms

Phono input gain : 46dB

S/PDIF coaxial input : up to 24bit and 192kHz

S/PDIF optical input : up to 24bit and 96kHz

USB input : USB Audio Class 2 requires USB 2.0 or higher on computer

USB data transfer : Asynchronous

Digital to Analogue converter : Cirrus Logic CS4344 24bit/192kHz Multi-bit Delta Sigma type

Variable line level output : jack 3.5mm

BT version: 2.1 +EDR

BT music receiver codec : aptX, A2DP profile

BT maximum TX power : +4dBm

Speakers connectors: 4mm banana plugs, spades connectors or naked wire

Headphone output : 6,3mm jack (16 –600ohms)

Outboard power supply : 20V/3A DC, suitable for your country's mains supply

Power consumption : max. 3A DC, <0.5W in standby

Replacement battery remote control : 1 x CR2032 / 3V or 1 x CR2025 / 3V

Dimensions W x H x D (D with sockets) : 206 x 38 x 165 (176)mm

Weight : 925 g without power supply

Should you encounter a problem which you are not able to alleviate or identify, please contact your dealer for

further advice. Only if the problem cannot be resolved there, the unit should be sent to the responsible

distributor in your country.

Warranty

The manufacturer accepts no responsibility for damage caused by not adhering to these instructions

for use. Modification or changes to any part of the product by unauthorized persons release the

manufacturer from any liability over and above the lawful rights of the customer.

Pro-Ject Audio Systems is a registered Trademark of

H. Lichtenegger.

This guide was produced by: Pro-Ject Audio Systems

The information was correct at the time of going to

press. The manufacturer reserves the right to make

changes to the technical specification without prior

notice as deemed necessary to uphold the ongoing

process of technical development.

BT® is a trademark owned by the BT SIG, Inc., , Microsoft®, Windows®, are either registered trademarks or

trademarks of Microsoft Corporation, Apple is registered trademark of Apple Inc., Android™is a trademark of

Google Inc.

Waste from Electrical and Electronic Equipment (WEEE): This directive mandates the collection and recycling

of electronics and component materials in order to reduce the amount going to landfills. Outside North

America, when the user decides to discard this product, it must be sent to a separate collection facility for

recycling. Please contact your point of purchase for more details.

Federal Communication Commission (FCC) Interference Statement FCC Part 15: This equipment has been

tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna

- Increase the separation between the equipment and receiver

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

- Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation. FCC Radiation Exposure Statement: This equipment

complies with FCC radiation exposure limits set forth for an uncontrolled environment.

To maintain compliance with FCC´s RF exposure guidelines, this equipment should be installed and operated

with minimum distance 20cm between the radiator and your body. Use on the supplied antenna.

Contains FCC ID: 2ACCRMB05

Declaration of Conformity

We, Canor spol. s r.o.

Družstevná 13925/39

08006 Prešov

Slovakia

(manufacturer)

and

Pro-Ject Audio Systems a division of Audio Tuning GmbH

Margaretenstrasse 98

1050 Vienna,

Austria

(distributor)

declare under our responsibility that the product is in conformity with the provisions of Directives:

2014/35/EU including amendments

2014/30/EU including amendments

2014/53/EU including amendments

The following harmonised standards were applied:

Health: EN62479:2010

Safety: EN60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013, EN62368-1:2014/A11:2017,

EN61558-1:2005/A1:2009, EN61558-2-16:2009/A1:2013

EMC: EN301489-1 V2.2.0: 2017-03, EN301489-17 V3.2.0:2017-03, EN55032:2015, EN55035:2017,

EN61000-3-2:2014, EN61000-3-3:2013

Radio Spectrum: EN300328 V2.1.1 (2016-11)

Pro-Ject Audio Systems a division of Audio Tuning GmbH

1050 Vienna, Austria, Margaretenstrasse 98

[email protected]

Other manuals for Remote Box S2

Table of contents

Other Pro-Ject Audio Systems Amplifier manuals

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject Phono Box S User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pre Box S2 Analogue User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Record Box E User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pre Box SE User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Phono Box DS User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Box Design Pre Box RS2 Digital User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Head Box SE II User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Phono Box II USB User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Phono Box USB V User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Phono Box MK II User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Stereo Box DS3 User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Amp Box User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject MaiA User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Phono Box RS User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Phono Box SE II User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Stereo Box User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Stereo Box User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Phono Box MM User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Phono Box USB V User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Stereo Box S Phono User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject Audio Systems User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pre Box User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Head Box II User manual

Pro-Ject Audio Systems

Pro-Ject Audio Systems Tube Box SE II User manual

Popular Amplifier manuals by other brands

ASTRO

ASTRO HVO V40 P operating manual

Marantz

Marantz SUPERSCOPE BLA-545 Service data

NAD

NAD CI980 Quick setup guide

Technics

Technics SE-CH770 Service manual

Harman Kardon

Harman Kardon HK6300 instruction manual

NAD

NAD T975 owner's manual

McIntosh

McIntosh MA6850 Brochure & specs

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N manual

Viatron

Viatron Autrix Technical manual

GME

GME GA9800 instruction manual

Atlas

Atlas CP700 Specification sheet

Roland

Roland KC-1000 owner's manual

Pyle

Pyle PFMRA350BW user manual

Advantage

Advantage S-250 manual

IRT Electronics

IRT Electronics DVA-3007 manual

Dimavery

Dimavery BA-100 Series user manual

Sony

Sony XM-S400D operating instructions

Schertler

Schertler ROY X quick guide