Prismasonic Cinoscreen F-100 User manual
Video Screen
Cinoscreen F-100 / F-AT100
A Picture to
Remember
Assembly Instructions
INSTALLATION INSTRUCTIONS
Carefully remove and unwrap all the contents of box. Referring to the parts list, make
sure you have everything needed to proceed with the installation of the screen. If any
parts are missing, contact Prismasonic immediately.
Inspect the screen to make sure there are no shipping defects. If you notice a problem
with the screen itself, or the screen’s mechanical system, contact Prismasonic
immediately.
Part List:
Screen Fabrics
Screen Fabric (F-AT models have two white woven fabrics included )
Back Fabric (F-AT models only, comes as a different package)
Wooden parts
Framework Bar (8 pcs)
Velvet Frames (6 pcs)
Corner Blocks (4 pcs)
Aluminum Brackets
Corner Bracket (4 pcs)
Extension Bracket (2 pcs)
Fabric Holder (22 pcs, 116” || 22 pcs, 136” || 26 pcs, 156”)
Fabric Holder with a Plate (4 pcs)
Frame Holder (18 pcs) (Do not exist if ordered with a masking system)
Frame Holder Plate (6 pcs) (Do not exist if ordered with a masking system)
Wall Mount (2 pcs)
Wall Mount Side (4 pcs)
Wall Plate (2 pcs)
Wall Plate Side (4 pcs)
Wall Socket, 16 mm (8 pcs)
Hardware
Set Screw, M4 x 30 (12 pcs) (Do not exist if ordered with a masking system)
Set Screw, M6 x 30 (26 pcs, 116” || 26 pcs, 136” || 30 pcs, 156”)
Set Screw, M8 x 6 (4 pcs)
Washer , M10 (26 pcs, 116” || 26 pcs, 136” || 30 pcs, 156”)
Hex Nut , M10 (26 pcs, 116” || 26 pcs, 136” || 30 pcs, 156”)
Cap Screw, M4 x 35 (6 pcs) (Do not exist if ordered with a masking system)
Cap Screw, M6 x 16 (8 pcs)
Cap Screw, M6 x 25 (18 pcs) (Do not exist if ordered with a masking system)
Cap Screw, M8 x 50 (4 pcs)
Torx Screw, 5 x 30, black (42 pcs || 36 pcs if ordered with a masking system)
Tools
L-wrench, 3 mm
L-wrench, 4 mm
L-wrench, 6 mm
Driver, Torx
Spanner Wrench, adjustable
Staple Gun (F-AT models only)
Staples, 8 mm (F-AT models only)
------------------------------------------------------------
Assembly Instructions
STEP 1
Attach the two Wall Plates and four Wall Plate sides to wall exactly as presented in Fig 1a. There are five
holes in Wall Plate and three holes in Wall Plate side, which can be used for screw connections to wall. Make
sure the plates are oriented correctly and the distances are as informed, depending on the screen size. After
this attach the wall Sockets to the screw threads marked with x). Tighten the sockets securely and make sure
the heels of sockets come in contact with the plates. (Fig 1b and Fig 1c).
NOTE: Please consult the professional installer if you do NOT know an appropriate way to attach heavy loads to
your wall material.
Assembly Instructions: STEP 2
By using the L-Wrench, 3mm, screw the Set Screw m6 x 30 inside the each Fabric holder so that the bottom of
the screw will be in the same level as the bottom of the holder (Fig 2a). Now prepare to attach the Wall Mounts
onto the two Extension Brackets, and the Wall Mount Sides, one onto the each four Corner Brackets (Fig 2b
and Fig 2c). By using L-Wrench 4 mm, tighten every Cap Screw m6 x 16 securely. Attach also the wooden
Corner Block to each four Corner Bracket exactly as shown in a Fig 2d. At this point the Fabric Holder (Fig 2e)
is temporarily inserted inside the Corner Block to ensure it fitting there also after tightening the To rx Screws, 5
x 30.
Fig 2
a)
Video Screen
Cinoscreen F-100 / F-AT100
116”: 1238 mm
136”: 1438 mm
156”: 1638 mm
Fig 1a
x)
x) x)
116”: 1001 mm
136”: 1235 mm
156”: 1475 mm
Fig 1c
Fig 1b
Fig 2
b)
g)
Fig 2
c)
d)
e)
f)
Fig 2
h)
... Screw also two set screws, m4 x 30 to each Corner Bracket
and Extension Bracket, exactly as presented in Fig 2f and
2g, so that the screw head does not exceed the bottom
surface of the bracket.
As shown in Fig 2h, attach the six Frame Holders to six
Frame Holder Plates with Cap Screw m4 x 35. Tighten the
each screw securely by using L-Wrench, 3 mm.
NOTE! Ignore the steps shown in f) , g) and h) when assemble
together with the Cinomask masking system.
Assembly Instructions
STEP 3
Starting from the upper horizontal frameworks, attach the Corner Bracket and Extension Bracket to
horizontal Framework Bar with the Torx Screws, as shown in a Fig 3. Again as in case of Corner Bracket
(Fig 2e), it is recommendable to insert the Fabric Holder temporarily inside the slot marked by a) to ensure it
fitting there also after tightening the To rx Screws of Extension Bracket. Make also sure the Corner Bracket
becomes in contact with the recess edge of Framework Bar, as marked by b). Then lift the bar hanging to
the Wall Sockets of Wall Plates.
Fig 5
Video Screen
Cinoscreen F-100 / F-AT100
Fig 4
STEP 4
Similarly now built the other side of upper horizontal framework bar, but now first string the Wall Mount Side
to the Wall Socket in side, after which connect the other end to the Extension Bracket, exactly as presented in
Step 3.
Finally do the same procedure to the lower horizontal Framework Bars, which are full mirror images for the
upper bars.
STEP 5
Now complete the framework by adding the vertical side and center bars (Fig 5). The side bars are attached to
corner brackets with Torx S crews. It is important that the side bars are oriented so that the hole on a recess of
both bars are located on the side of wall (Fig 5b). Again make sure the each Corner Bracket becomes in
contact with the recess edge of Framework Bar, similarly as with horizontal bars, marked by b) in Fig 3.
The vertical center bars are attached to horizontal bars by two Cap Screws m8 x 50. The bars are oriented so
that the recess is formed to the opposite side of wall as shown in Fig 5c. Tighten the all screws securely by
using the L-wrench, 6 mm.
Still screw the four Set Screws, m6 x 8 to the screw holes of both upper and lower Wall Mounts at location
shown in Fig 3c to an extent that prevents the bars falling from the Wall Socket.
Fig 3
b)
a)
c) c)
c)
wall
recess
wall
b)
Assembly Instructions
STEP 6 (F-AT models only)
Connect the Black Mask Fabric onto the front side of framework by staples. Shoot one staple in about every 20
cm, after which cut the fabric to match the framework size by scissors or carpet knife. It is not important how the
back fabric looks as long as it covers the area inside the outer framework bars. Neither it does not have to be 100%
tensed. (It will finally be covered by the actual screen fabric and the velvet frames anyway.)
STEP 7
Prepare to connect the Screen Fabric to Fabric
Holders, which are inserted inside into the slots of
framework bars, as shown in Fig 7a. Use Washer,
10 mm and Nut, 10 mm to fasten the fabric. The
Fabric Holderswith a Plate are placed in each four
corner (Fig 7b)
STEP 10
Now the rest of Fabric Holders are inserted to Frame work bars, and the Screen Fabric is attached to those
again exactly as shown in Fig 7a. And after this those spots are also tightened according to instructions in Step
9. If there still exist some loosen areas on screen the further tightening can still be performed, until the surface is
perfectly flat.
Video Screen
Cinoscreen F-100 / F-AT100
Fig 7a (back view)
Fig 7b
Fig 8
STEP 8
Place the Fabric Holders first to the horizontal top frame work bars and to the top corners, after which,
starting from corner, roll the fabric open and simultaneously string the tabs of fabric to every Fabric Holder
on top corners and bars. After this insert the Fabric Holders also to the spots marked with the arrows in Fig
8. Now, exactly as presented in Fig 7a, lock the fabric to the holders, BUT FIRST ONLY FROM THE SPOTS
MARKED WITH ARROWS IN FIG 8, even if the top bars already have the rest of holders in their place.
Tighten the ten nuts securely by using the Spanner Wrench.
NOTE! With F-AT model place the two white woven fabrics, one after another on top with each other, so that the
one with a diagonal surface pattern stays on top.
Fig 9
STEP 9
The fabric is now tightened first from the spots
marked with arrows in Fig 8. Using the L-
Wrench, 3mm, screw the set screws inside the
Fabric Holders clock wise, each for 4-5 full turns.
Before tightening make sure that in every four
corner the fabric tabs bends entirely over the
front edge of the fabric holder plate, exactly as
shown with arrows in Fig 9
Care and Maintenance (CinoWhite and CinoAT Fabrics)
Clean surface with a solution of mild dishwashing liquid
diluted with warm water. Sponge the surface, rinse with clear
water and blot dry. It is also possible to use cleaning solvents
or abrasives.
Fig 11 (back view)
a)
a)
b)
STEP 11
Velvet Frames are now attached to the framework bars. First prepare to connect the two Frame Holders to the
side threads of each six velvet frame parts with Cap Screw m6 x 16 (Fig 11a). Similarly attach the frame holder
assembly (Fig 2h and Fig 11b) to each center thread of velvet frame. Tighten all screws securely by using L-
Wrench 4 mm. Finally, repeating this for all six velvet frames, string the Frame Holders in side to the set screws,
assembled in Step 2 (Fig 2f and 2g), and connect the center Frame Holder with a plate onto the slot in the
framework bar using the Torx Screw. Tighten the screws of each velvet frame securely using the Screw Driver,
torx. Still match the joints of frames perfectly to each other and You’re done. ... Enjoy your new 2.40:1 picture!
NOTE: If the motorized mask system is also installed, do not perform the step 11, but start to follow the user manual
of Cinomask F-100.
This manual suits for next models
3
Other Prismasonic Monitor manuals
