Prins VSI User manual
MAKE OF AUTOMOBILE:
Renault
TYPE:
Clio 3
PISTON DISPLACEMENT:
1200cc
NUMBER OF VALVES:
16v
ENGINE NUMBER:
D4F (TCe100)
TRANSMISSION TYPE ( MT / AT )
MT
VEHICLE CATEGORIES M or N
M
TYPE VSI INJECTOR ( COLOUR )
Blue, KN8
VERSION ( LPG / CNG )
LPG
INJECTION SYSTEM:
CONTINENTAL SIM32
MODEL YEAR:
2011
SYSTEM APPROVAL NUMBER ( R115 )
E13#R115-000027 VSI-LPG24
LOCATION SYSTEM STICKER
If applicable : right side, centre door post
ENGINE SET NUMBER
359/030001
NUMBER :
076/1906100
DATE :
2014-08-12
Copyright © Prins Autogassystemen B.V. 2011VERSION NR :
2010-07-29 C
TABLE OF CONTENTS
General instructions............................................................................................................................. 2
Required equipment / tools / materials for installing a complete system............................................. 3
Vehicle check....................................................................................................................................... 3
Base diagram....................................................................................................................................... 4
VSI approval numbers.......................................................................................................................... 5
Mounting and connection points .......................................................................................................... 6
Mounting the reducer........................................................................................................................... 7
Water connections............................................................................................................................... 8
Overpressure connection..................................................................................................................... 9
Mounting the inlet manifold couplings................................................................................................ 10
Mounting the ValveCare manifold couplings...................................................................................... 11
Mounting the VSI injector rail............................................................................................................. 12
Mounting the Prins filter unit............................................................................................................... 13
Mounting ValveCare 1........................................................................................................................ 14
Mounting ValveCare 2........................................................................................................................ 15
LPG hoses ......................................................................................................................................... 16
Mounting the VSI computer bracket................................................................................................... 17
Mounting the fuel selection switch ..................................................................................................... 18
Electrical connections ........................................................................................................................ 19
Electrical connections ........................................................................................................................ 20
Insulate all not used wires.................................................................................................................. 20
Electrical connections ........................................................................................................................ 21
Checklist after installation .................................................................................................................. 22
Trouble code chart............................................................................................................................. 23
FOR EXPLANATION AND CIRCUIT DIAGRAMS SEE : INSTALLATION MANUAL GENERAL PART 1 / 2
EXPLANATION OF SYMBOLS :
= IMPORTANT, CAUTION
PAGE 2
076/19060100
Copyright © Prins Autogassystemen B.V. 2011
Renault
Clio 1.2 16v TCe100 2011
VERSION NR : C
2
General instructions
The installation of the system shall be done in accordance with the installation manual provided by Prins
Autogassystemen.
This manual is based on Dutch regulations, always install the system in accordance to the local regulations.
Always download the “general manual ½ “ from our website for basic instructions and diagrams.
Always disconnect the battery when installing the LPG system. Make sure the ignition key is outside the car.
Be aware of central door locking, radio / telephone memory code, alarm system.
Do not place the main fuse into the fuse holder before having completed the installation of the VSI system.
The VSI computer has to be activated by means of the diagnosis software.
In the unlikely event the VSI computer fails, it will automatically switch over to petrol.
Never disconnect the VSI computer connector, unless you have removed the main fuse.
When installing the VSI wiring harness, ensure that it does not run near any of the ignition components.
Solder and insulate all electrical connections.
The wires in the loom are provided with numbers and text. The text on the wire explains the function of the
wire. The wire harness is not model specific, therefore is it may be necessary to adjust the length of the
wires. Ensure maximum care is taken when connecting wiring.
Make professional joints using solder and shrink sleeve. Do not stretch the wiring harness.
No component of the LPG-system shall be located within 100 mm of the exhaust or similar heat source,
unless such components are adequately shielded against heat.
Remove any internal burrs, after having shortened the LPG pipe. (This guarantees the maximum flow
through the pipe without pollution.)
If holes have to be drilled (wear safety glasses) for installing brackets, etc., the drilled holes must always be
treated with an anti-corrosion agent, after the chips have been removed ( especially when mounting a
exterior filler into body work).
After having completed the installation, check the whole system for gas leakage; use a gas leak detection
device. Also check for leak of engine coolant, petrol and air.
Fitting and maintenance is only allowed by Prins Autogassystemen selected LPG engineers.
Failure to follow the instructions in this manual can result in a poor or non-working gas installation or a
dangerous situation.
For maintenance instructions and filter registration see owner manual.
Prins Autogassystemen is not responsible for any damages to people or objects as a result of changes to
Prins products.
Check our website regularly for diagrams, certificates, updates, info-bulletins and product information.
Please fill in the warranty card completely and return it within 8 days after installation.
PAGE 3
076/19060100
Copyright © Prins Autogassystemen B.V. 2011
Renault
Clio 1.2 16v TCe100 2011
VERSION NR : C
3
Required equipment / tools / materials for installing a complete system
-Complete workshop toolbox ( wrenches, screwdrivers, cutters, pliers, ratchet, sockets )
-Car lift
-Portable computer : operating on Windows 98,W2000 or XP.
Internal memory : 16 Mb or more
Memory HD space : 5MB
Screen : 256 colours, advise colours 16 bits or more
Com port : 1 free COM port 1 or COM port 2 with a 9 or 25 pins connector
-Vehicle fuel system scan tool or OBD scan tool Prins ( part nr. 099/99928 )
-Exhaust gas analyser
-Multimeter
-Oscilloscope
-Prins VSI diagnostic software
-Prins VSI serial interface
-Prins VSI break out box ( part nr. 080/70090 )
-Torque wrench ( 10Nm )
-Portable light
-Assortment drill bits 4 to 12 mm
-Assortment cutters ( ø 20, 30, 50, 70 mm )
-Punching tool ø 70 mm
-Round file
-Portable drill or pneumatic drill
-Threading device ( male M6x1, M8x1, M10x1 )
-Pipe-flaring tool ( for 6 and 8 mm copper pipe )
-Air gun
-Vacuum cleaner
-Hot air gun
-Allan spanner for inlet couplings 3,5mm ( part nr. 099//9970 )
-Reducer adjustment tool ( part nr. 099/9960 )
-Molex extraction tool for VSI switch connector ( part nr. 090/9929 )
-Soldering iron, soldering tin
-Wire-stripping pliers
-Adhesive tape
-Adhesive sealant
-Thread locking compound
-Anti-corrosion agent / black body coating
-Gas leak detection device or foam leak spray
-Shrink sleeves
-Engine coolant
Vehicle check
-Check the vehicle drivability on petrol
-Check the fuel system for error codes ( scan tool )
-Check if the catalytic converter is in good condition ( exhaust gas analyzer )
-Check the condition of the ignition system ( spark plugs, cables, coil )
PAGE 4
076/19060100
Copyright © Prins Autogassystemen B.V. 2011
Renault
Clio 1.2 16v TCe100 2011
VERSION NR : C
4
Base diagram
PAGE 5
076/19060100
Copyright © Prins Autogassystemen B.V. 2011
Renault
Clio 1.2 16v TCe100 2011
VERSION NR : C
5
VSI approval numbers
Reducer VSI LPG Prins : E4-67R-010054
Lock-off valve OMB : E8-67R-014327
Lock-off valve Valtek : E4-67R-010041
Injector rail Prins : LPG E4-67R-010093
CNG E4-110R-000021
Filter unit T1 / T2 Prins : LPG E4-67R-010096
CNG E4-110R-000028
Filter unit Keihin : LPG E4-67R-010177
CNG E4-110R-000091
Injector Keihin :LPG E4-67R-010092
CNG E4-110R-000020
Computer VSI- 4 / 6 Prins: LPG E4-67R-010098
CNG E4-110R-000083
LPG hoses Tubithor : LPG E13-67R-010145
CNG E13-110R-000017
Rubia : LPG E4-67R-010068
CNG E4-110R-000003
PAGE 6
076/19060100
Copyright © Prins Autogassystemen B.V. 2011
Renault
Clio 1.2 16v TCe100 2011
VERSION NR : C
6
Mounting and connection points
A : Reducer
I : Lambda signal ( 19 + 20 )
B : Filter unit
J : “-“ interruption petrol injector
C : Injector rail
K : Overpressure coupling
D : VSI Computer
L : R115 Approval sticker
E : Injection module
M : grommet
F : Water connections
N : Turbo / MAP signal
G : “+” petrol injectors ( 112 )
V : ValveCare pump
H : Engine speed signal RPM ( 8 )
Q : ValveCare distributor
R115 approval sticker :
Right side centre door post
PAGE 7
076/19060100
Copyright © Prins Autogassystemen B.V. 2011
Renault
Clio 1.2 16v TCe100 2011
VERSION NR : C
7
Mounting the reducer
Filter replacement must be recorded in the service book supplied
Remove battery, battery holder and air filter housing.
Mount reducer bracket on original bolt on left chassis beam.
Mount hoses on reducer. For length of hoses see page 16. Mount protection on 16mm hose.
Mount reducer on bracket with M8 nut and spring washer.
PAGE 8
076/19060100
Copyright © Prins Autogassystemen B.V. 2011
Renault
Clio 1.2 16v TCe100 2011
VERSION NR : C
8
Water connections
Cut hoses. Mount T-pieces 20x16x20mm with clamps.
Routing water hoses.
PAGE 9
076/19060100
Copyright © Prins Autogassystemen B.V. 2011
Renault
Clio 1.2 16v TCe100 2011
VERSION NR : C
9
Overpressure connection
Drill a hole of Ø5mm and cut thread M6 in this hole.
Place a VSI coupling with a lock compound to the inlet manifold.
Connect overpressure / MAP hose from reducer.
Table of contents
