PRETUL LIOR-1/3P3 User manual

Manual

Finishing Sander

LIOR-1/3P3

Model Code

LIOR-1/3P3

Applies for:

23999

Power Sanding sheet

1/3

0,2 Hp

ENGLISH

ESPAÑOL

CAUTION Read the user’s manual thoroughly

before operating this tool.

Technical Data

Power Requirements

General Power Tool Safety Warnings

Safety Warnings for Sanders

Parts

Start Up

Maintenance

Authorized Service Centers

Warranty Policy

LIOR-1/3P3

ENGLISH

CAUTION

Contents

Keep this manual for future references.

The illustrations in this manual are for reference

only. They might be different from the real tool.

To gain the best performance of

the tool, prolong the duty life,

make the Warranty valid if

necessary, and to avoid hazards

of fatal injuries please read and

understand this Manual before

using the tool.

LIOR-1/3P3

23999

3-1/2” x 7-3/8”

Class II IP20

IP Grade

60 Hz

Finishing Sander

18 AWG x 2C with 167 °F insulation temperature.

20 minutes’ work per 10 min rest. Maximum 1 hour daily .

12000 orbits/min

Code

Description

Sanding Surface

Voltage

Frequency

1,25 A

Current

Speed

0,2 Hp

Power

Work Cycle

Conductors

Insulation

Power cord grips used in this product: Type “Y”.

Build quality: Reinforced insulation

Thermal insulation on motor winding: Class E

127 V

ENGLISH

Power Requirements

Technical Data

WARNING

WARNING Avoid the risk of electric shock or severe injury. When the power cable gets damaged

it should only be replaced by the manufacturer or at a Authorized Service Center.

The build quality of the electric insulation is altered if spills or liquid gets into the tool while in use.

Do not expose to rain, liquids and/or dampness.

Before gaining access to the terminals all power sources should be disconnected.

Tools with double insulation and reinforced insulation are

equipped with a polarized plug (one prong is wider than the other). This plug will

only fit in the right way into a polarized outlet. If the plug cannot be introduced into

the outlet, reverse the plug. If it still doesn’t fit, call a qualified electrician to install

for you a polarized outlet. Do not alter the plug in any way. Both insulation types

eliminate the need of both a grounded third power cord with three prongs or a

grounded power connection.

When using an extension cable, verify the gauge is enough for the power that your product needs. A lower

gauge cable will cause voltage drop in the line, resulting in power loss and overheating. The following table shows the right

size to use depending on cable’s length and the ampere capability shown in the tool’s nameplate. When in doubt use the

next higher gauge.

WARNING

from 0 A and up to 10 A

from 10 A and up to 13 A

from 13 A and up to 15 A

from 15 A and up to 20 A

18 AWG(*)

16 AWG

14 AWG

8 AWG

16 AWG

14 AWG

12 AWG

6 AWG

3 (one grounded)

from 6’ to 49’ | higher than 49’

Ampere

Capacity Number of

Conductors Extension gauge

*It is safe to use only if the extensions have a built-in artifact for over current protection.

AWG = American Wire Gauge. Reference: NMX-J-195-ANCE

WARNING When operating power tools outdoors, use a grounded

extension cable labeled “For Outdoors Use”. These extensions are specially designed for

operating outdoors and reduce the risk of electric shock.

This tool is in compliance with

the Official Mexican Standard

(NOM - Norma Oficial Mexicana).

Work area

Keep your work area clean, and well lit.

Cluttered and dark areas may cause accidents.

Never use the tool in explosive atmospheres, such as in the

presence of flammable liquids, gases or dust.

Sparks generated by power tools may ignite the flammable material.

Keep children and bystanders at a safe distance while operating

the tool.

Distractions may cause loosing control.

Electrical Safety

The tool plug must match the power outlet. Never modify

the plug in any way. Do not use any adapter plugs with

grounded power tools.

Modified plugs and different power outlets increase the risk of electric shock.

Avoid body contact with grounded surfaces, such as pipes,

radiators, electric ranges and refrigerators.

The risk of electric shock increases if your body is grounded.

Do not expose the tool to rain or wet conditions.

Water entering into the tool increases the risk of electric shock.

Do not force the cord. Never use the cord to carry, lift or unplug

the tool. Keep the cord away from heat, oil, sharp edges or

moving parts.

Damaged or entangled cords increase the risk of electric shock.

When operating a tool outdoors, use an extension cord suitable

for outdoor use.

Using an adequate outdoor extension cord reduces the risk of electric shock.

If operating the tool in a damp location cannot be avoided, use

a ground fault circuit interrupter (GFCI) protected supply.

Using a GFCI reduces the risk of electric shock.

Personal safety

Stay alert, watch what you are doing and use common sense

when operating a tool. Do not use a power tool while you are

tired or under the influence of drugs, alcohol or medication.

A moment of distraction while operating the tool may result in personal injury.

Use personal protective equipment. Always wear eye

protection.

Protective equipment such as safety glasses, anti-dust mask, non-skid shoes,

hard hats and hearing protection used in the right conditions significantly

reduce personal injury.

Prevent unintentional starting up. Ensure the switch is in the

“OFF” position before connecting into the power source and /

or battery as well as when carrying the tool.

Transporting power tools with the finger on the switch or connecting power

tools with the switch in the “ON” position may cause accidents.

Remove any wrench or vice before turning the power tool on.

Wrenches or vices left attached to rotating parts of the tool may result in personal

injury.

Do not overreach. Keep proper footing and balance at all times.

This enables a better control on the tool during unexpected situations.

Dress properly. Do not wear loose clothing or jewelry. Keep

hair, clothes and gloves away from the moving parts.

Loose clothes or long hair may get caught in moving parts.

If you have dust extraction and recollection devices connected

onto the tool, inspect their connections and use them correctly.

Using these devices reduce dust-related risks.

Power Tools Use and Care

Do not force the tool. Use the adequate tool for your

application.

The correct tool delivers a better and safer job at the rate for which it was designed.

Do not use the tool if the switch is not working properly.

Any power tool that cannot be turned ON or OFF is dangerous and should be

repaired before operating.

Disconnect the tool from the power source and / or battery

before making any adjustments, changing accessories or

storing.

These measures reduce the risk of accidentally starting the tool.

Store tools out of the reach of children. Do not allow persons

that are not familiar with the tool or its instructions to

operate the tool.

Power tools are dangerous in the hands of untrained users.

Service the tool. Check the mobile parts are not misaligned or

stuck. There should not be broken parts or other conditions that

may affect its operation. Repair any damage before using

the tool.

Most accidents are caused due to poor maintenance to the tools.

Keep the cutting accessories sharp and clean.

Cutting accessories in good working conditions are less likely to bind and are

easier to control.

Use the tool, components and accessories in accordance with

these instructions and the projected way to use it for the type of

tool when in adequate working conditions.

Using the tool for applications different from those it was designed for, could

result in a hazardous situation.

Service

Repair the tool in a Authorized Service Center

using only identical spare parts.

This will ensure that the safety of the power tool is maintained.

General power tool

safety warnings

WARNING! Read carefully all safety warnings and instruction listed below. Failure to comply with any of

these warnings may result in electric shock, fire and / or severe damage. Save all warnings and instructions for

future references.

4ENGLISH

• Observe applicable regulations when

sanding painted surfaces. Use extra care when the paint is

lead-based.

• Remove dust and any other type of debris to assure a

safe working environment. When possible use a vacuum

cleaner or a dust extractor.

• To be protected against dust and smoke

generated when sanding everybody in the work area

should wear a professional breathing mask.

• Do not use this tool to sanding pieces containing

magnesium or asbestos.

• After long work cycles the metallic outer parts and

accessories may get hot.

• Use a professional

breathing mask and cartridges suited for paint dust and

vapors. Regular painter masks do not offer the right

protection.

• Do not allow children and pregnant

women enter the work area.

• Remove the dust collecting container

(not included) before sanding metal. Sparks may ignite

dust and the inner pouch.

• Do not use worn or ripped sanding sheets.

• Do not touch the sanding sheet when moving.

• Before sanding, double-check all foreign objects such as

nails or screws are removed from the work piece.

• Hold the tool by the insulated

gripping surfaces. The sander belt could make contact

with its own feeding power cable.

Contact with a power conducing cable makes the tool

metal parts are also powered and give the operator an

electric shock.

Parts

Start Up

Dust

Extraction

Duct

Front

Handle

Switch

Handle

Continuous

Use Button Power Cord

Protector

Power

Cord

Sanding Sheet Clamp Vacuum

Cleaner Adaptor

Sander Pad

• Before setting up the sander select the right grain for

the job.

• Grains available vary from very coarse to very fine.

• Coarse grain is used to sand rough surfaces, medium

grain for light work and fine, for finishing purposes.

• Is advisable to test with disposable pieces to determine

the right grain for each particular job.

• Do not use the same sheet to sand wood or metal.

Metal particles may embed into the sander and damage

the wood surface.

Selecting the Sanding Sheet

Grain Type

60 or lower

80 - 100

120 - 150

180 - 220

240 or higher

very coarse

coarse

medium

fine

very fine

• In case the sanding sheet installed has no matching

orifices, punch the holes so that the dust extraction

system works right.

CAUTION

WARNING

ENGLISH

Safety warnings for

Sanders

• To install the sanding sheet, release the clamps on both sides of

the sander.

• Set one end of the sanding sheet under one of the clamps and

secure. Pull the other end so it stays uniformly onto the base.

• Verify the orifices (if any) match those in the base. Then adjust the

other side.

• The sheet must be perfectly fastened; otherwise there could be

excessive wear in the base.

Do not keep on using the tool if the sanding sheet is

worn or damaged.

the carbon housing. Ask to have the tool turned on and

keep it running 5 minutes to make even the contact of

carbons and commuter.

Use only original spare carbon

brushes, designed specifically with the right strength and

electric resistance for each type of motor. Carbon brushes

with different specifications may damage the motor.

When replacing carbon brushes both carbons should be

replaced simultaneously.

• Intermittent Operation:

Connect the plug into the power outlet.

To turn on the tool, press switch (A).

To turn off the tool, just release the switch.

• Continuous Operation:

Connect the plug into the power outlet.

Press the switch (A) and block it pushing the continuous use button (B).

To stop its function, press the switch and then release it.

Do not turn on the tool when the sanding sheet surface is onto

the work piece.

Before turning off the tool move it away from the work piece.

Start Up

Maintenance

Installing the Sanding Sheet

• Turn on the sander before setting it on the work piece. Hold it with both hands, one in the handle, the other in front handle.

• Keep the sander base parallel to the work piece surface.

• Press downwards making circular movements and verifying the entire sander base is supported on the work piece.

• Use moderate pressure. Do not force the sander. Run in at a moderate speed. Overheating may occur if too much

pressure is applied. The motor will run slow leading to inefficient sanding and damage to the motor.

• If after sanding you see marks on the work piece surface sand again using a sanding sheet with coarser grain to eliminate

the marks. To finish the sanding operations, replace back the previous sanding sheet. Replace the worn sheet with a new one.

• Do not wear out the sanding sheet completely. Replace before starts wearing out.

Sander Operation

Keep the motor housing ventilation slots clean and

uncovered. Apply compressed air after each use. In case

of malfunctioning go only to Authori-

zed Service Center.

Checked periodically the carbon brushes when worn.

Replace only at a Authorized Service

Center. After replacing the carbons ask the technician to

double-check the new carbon brushes can move freely in

Cleaning and Care

Carbon Brush Replacement

Start Up and Operation Control

CAUTION

ENGLISH

Authorized Service Centers

In the event of any problem contacting a Service Center, please see our webpage www.truper.com to get an

updated list, or call our toll-free numbers 800 690-6990 or 800 018-7873 to get information about the

nearest Authorized Service Center.

AGUASCALIENTES

BAJA

CALIFORNIA SUR

CAMPECHE

CHIAPAS

CHIHUAHUA

MÉXICO

CITY

COAHUILA

COLIMA

DURANGO

ESTADO DE

MÉXICO

GUANAJUATO

GUERRERO

HIDALGO

JALISCO

MICHOACÁN

MORELOS

NAYARIT

DE TODO PARA LA CONSTRUCCIÓN

GRAL. BARRAGÁN #1201, COL. GREMIAL, C.P. 20030,

AGUASCALIENTES, AGS. TEL.: 449 994 0537

SUCURSAL TIJUANA

AV. LA ENCANTADA, LOTE #5, PARQUE INDUSTRIAL EL

FLORIDO II, C.P 22244, TIJUANA, B.C.

TEL.: 664 969 5100

FIX FERRETERÍAS

FELIPE ÁNGELES ESQ. RUIZ CORTÍNEZ S/N, COL. PUEBLO

NUEVO, C.P. 23670, CD. CONSTITUCIÓN, B.C.S.

TEL.: 613 132 1115

TORNILLERÍA Y FERRETERÍA AAA

AV. ÁLVARO OBREGÓN #324, COL. ESPERANZA

C.P. 24080 CAMPECHE, CAMP. TEL.: 981 815 2808

FIX FERRETERÍAS

AV. CENTRAL SUR #27, COL. CENTRO, C.P. 30700,

TAPACHULA, CHIS. TEL.: 962 118 4083

SUCURSAL CHIHUAHUA

AV. SILVESTRE TERRAZAS #128-11, PARQUE INDUSTRIAL

BAFAR, CARRETERA MÉXICO CUAUHTÉMOC, C.P. 31415,

CHIHUAHUA, CHIH. TEL. 614 434 0052

FIX FERRETERÍAS

EL MONSTRUO DE CORREGIDORA, CORREGIDORA # 22,

COL. CENTRO, C.P. 06060, CUAUHTÉMOC, CDMX.

TEL: 55 5522 5031 / 5522 4861

SUCURSAL TORREÓN

CALLE METAL MECÁNICA #280, PARQUE INDUSTRIAL

ORIENTE, C.P. 27278, TORREÓN, COAH.

TEL.: 871 209 68 23

BOMBAS Y MOTORES BYMTESA DE MANZANILLO

BLVD. MIGUEL DE LA MADRID #190, COL. 16 DE

SEPTIEMBRE, C.P. 28239, MANZANILLO, COL.

TEL.: 314 332 1986 / 332 8013

TORNILLOS ÁGUILA, S.A. DE C.V.

MAZURIO #200, COL. LUIS ECHEVERRÍA, DURANGO,

DGO.TEL.: 618 817 1946 / 618 818 2844

SUCURSAL CENTRO JILOTEPEC

AV. PARQUE INDUSTRIAL #1-A, JILOTEPEC, C.P. 54240,

JILOTEPEC, EDO. DE MÉX.

TEL: 761 782 9101 EXT. 5728 Y 5102

CÍA. FERRETERA NUEVO MUNDO S.A. DE C.V.

AV. MÉXICO - JAPÓN #225, CD. INDUSTRIAL, C.P. 38010,

CELAYA, GTO. TEL.: 461 617 7578 / 79 / 80 / 88

CENTRO DE SERVICIO ECLIPSE

CALLE PRINCIPAL MZ.1 LT. 1, COL. SANTA FE, C.P. 39010,

CHILPANCINGO, GRO. TEL.: (747) 478 5793

FERREPRECIOS S.A. DE C.V.

LIBERTAD ORIENTE #304 LOCAL 30, INTERIOR DE PASAJE

ROBLEDO, COL. CENTRO, C.P. 43600, TULANCINGO,

HGO. TEL.: 775 753 6615 / 775 753 6616

SUCURSAL GUADALAJARA

AV. ADOLFO B. HORN # 6800, COL: SANTA CRUZ DEL

VALLE, C.P.: 45655, TLAJOMULCO DE ZUÑIGA, JAL.

TEL.: 33 3606 5285 AL 90

FIX FERRETERÍAS

AV. PASEO DE LA REPÚBLICA #3140-A, COL.

EX-HACIENDA DE LA HUERTA, C.P. 58050, MORELIA,

MICH. TEL.: 443 334 6858

FIX FERRETERÍAS

CAPITÁN ANZURES #95, ESQ. JOSÉ PERDIZ, COL.

CENTRO, C.P. 62740, CUAUTLA, MOR.

TEL.: 735 352 8931

HERRAMIENTAS DE TEPIC

MAZATLAN #117, COL. CENTRO, C.P. 63000, TEPIC, NAY.

TEL.: 311 258 0540

SUCURSAL MONTERREY

CARRETERA LAREDO #300, 1B MONTERREY PARKS

COLONIA PUERTA DE ANÁHUAC, C. P. 66052, ESCOBEDO,

NUEVO LEÓN, N.L. TEL.: 81 8352 8791 / 81 8352 8790

FIX FERRETERÍAS

AV. 20 DE NOVIEMBRE #910, COL. CENTRO, C.P. 68300,

TUXTEPEC, OAX. TEL.: 287 106 3092

SUCURSAL PUEBLA

AV PERIFÉRICO #2-A, SAN LORENZO ALMECATLA,

C.P. 72710, CUAUTLACINGO, PUE.

TEL.: 222 282 8282 / 84 / 85 / 86

ARU HERRAMIENTAS S.A DE C.V.

AV. PUERTO DE VERACRUZ #110, COL. RANCHO DE

ENMEDIO, C.P. 76842, SAN JUAN DEL RÍO, QRO.

TEL.: (427) 268 4544

FIX FERRETERÍAS

CARRETERA FEDERAL MZ. 46 LT. 3 LOCAL 2, COL EJIDAL,

C.P. 77710 PLAYA DEL CARMEN, Q.R.

TEL. 984 267 3140

FIX FERRETERÍAS

AV. UNIVERSIDAD #1850, COL. EL PASEO, C.P. 78320,

SAN LUIS POTOSÍ, S.L.P. TEL.: 444 822 4341

SUCURSAL CULIACÁN

AV. JESÚS KUMATE SUR #4301, COL. HACIENDA DE LA

MORA, C.P. 80143, CULIACÁN, SIN.

TEL.: 667 173 9139 / 173 8400

FIX FERRETERÍAS

CALLE 5 DE FEBRERO #517, SUR LT. 25 MZ. 10, COL.

CENTRO, C.P. 85000, CD. OBREGÓN, SON.

TEL.: 644 413 2392

SUCURSAL VILLAHERMOSA

CALLE HELIO LOTES 1, 2 Y 3 MZ. #1, COL. INDUSTRIAL,

2A ETAPA, C.P. 86010, VILLAHERMOSA, TAB.

TEL.: 993 353 7244

VM ORINGS Y REFACCIONES

CALLE ROSITA #527 ENTRE 20 DE NOVIEMBRE Y GRAL.

RODRÍGUEZ, FRACC. REYNOSA, C.P. 88780, REYNOSA,

TAMS. TEL.: 899 926 7552

SERVICIOS Y HERRAMIENTAS INDUSTRIALES

PABLO SIDAR #132, COL . BARRIO DE SAN BARTOLOMÉ,

C.P. 90970, SAN PABLO DEL MONTE, TLAX.

TEL.: 222 271 7502

LA CASA DISTRIBUIDORA TRUPER

BLVD. PRIMAVERA. ESQ. HORTENSIA S/N, COL.

PRIMAVERA C.P. 93308, POZA RICA, VER.

TEL.: 782 823 8100 / 826 8484

SUCURSAL MÉRIDA

CALLE 33 #600 Y 602, LOCALIDAD ITZINCAB Y MULSAY,

MPIO. UMÁN, C.P. 97390, MÉRIDA, YUC.

TEL.: 999 912 2451

NUEVO LEÓN

OAXACA

PUEBLA

QUERÉTARO

QUINTANA ROO

SAN LUIS

POTOSÍ

SINALOA

SONORA

TABASCO

TAMAULIPAS

TLAXCALA

VERACRUZ

YUCATÁN

Model Code Brand

LIOR-1/3P3 23999

ENGLISH

Warranty Policy

www.truper.com

12-2019

Stamp of the business:

Date of purchase:

YEAR

This product, its parts and components have a one year warranty against defects in its

manufacture, operation and workmanship, except when: the product has been used in conditions

other than those recommended, or has not been operated according to the instructions, or has

been altered or repaired by personnel not authorized by . In order to make the

warranty valid or to purchase components and spare parts, you must present the product and its

proof of purchase at Av. San Isidro #110, Col. Industrial San Antonio, ALC. Azcapotzalco,

C.P. 02760, CDMX, Mex. or at the store where you bought it, or at a service

center listed in the attached warranty policy and/or at www.truper.com. Transportation costs

resulting from compliance of this warranty will be covered by . For questions or

comments, call 800-690-6990.

Imported by: Truper, S.A. de C.V. , Parque Industrial #1, Jilotepec, Edo. de Méx.,

Méx. C.P. 54240, Made in China

www.truper.com

12-2019

Póliza de Garantía

Modelo Código Marca

LIOR-1/3P3 23999

ESPAÑOL

Sello del establecimiento comercial:

Fecha de entrega:

AÑO

Este producto, sus piezas y componentes están garantizados por un año contra defectos de

fabricación, funcionamiento y mano de obra, excepto cuando: el producto haya sido usado en

condiciones distintas a las recomendadas, o no se haya operado de acuerdo al instructivo, o

haya sido alterado o reparado por personal no autorizado por . Para hacer

válida la garantía o adquirir piezas y componentes deberá presentar el producto y su

comprobante de compra en Av. San Isidro #110, Col. Industrial San Antonio, Alc. Azcapotzalco,

C.P. 02760, CDMX, Méx. o en el establecimiento donde lo compró, o en algún Centro de

Servicio de los enlistados en el anexo de la póliza de garantía y/o en

www.truper.com . Los gastos de transportación que resulten para su cumplimiento serán

cubiertos por . Para dudas o comentarios, llame al 800-690-6990.

Importado por: Truper, S.A. de C.V. , Parque Industrial #1, Jilotepec, Edo. de Méx.,

Méx. C.P. 54240, Hecho en China

Centros de Servicio Autorizados

ESPAÑOL

En caso de tener algún problema para contactar un Centro de Servicio consulte nuestra página www.truper.com

donde obtendrá un listado actualizado, o llame al teléfono: 800 690-6990 ó 800 018-7873 donde le informarán

cuál es el Centro de Servicio Autorizado más cercano.

AGUASCALIENTES

BAJA

CALIFORNIA SUR

CAMPECHE

CHIAPAS

CHIHUAHUA

CIUDAD DE

MÉXICO

COAHUILA

COLIMA

DURANGO

ESTADO DE

MÉXICO

GUANAJUATO

GUERRERO

HIDALGO

JALISCO

MICHOACÁN

MORELOS

NAYARIT

DE TODO PARA LA CONSTRUCCIÓN

GRAL. BARRAGÁN #1201, COL. GREMIAL, C.P. 20030,

AGUASCALIENTES, AGS. TEL.: 449 994 0537

SUCURSAL TIJUANA

AV. LA ENCANTADA, LOTE #5, PARQUE INDUSTRIAL EL

FLORIDO II, C.P 22244, TIJUANA, B.C.

TEL.: 664 969 5100

FIX FERRETERÍAS

FELIPE ÁNGELES ESQ. RUIZ CORTÍNEZ S/N, COL. PUEBLO

NUEVO, C.P. 23670, CD. CONSTITUCIÓN, B.C.S.

TEL.: 613 132 1115

TORNILLERÍA Y FERRETERÍA AAA

AV. ÁLVARO OBREGÓN #324, COL. ESPERANZA

C.P. 24080 CAMPECHE, CAMP. TEL.: 981 815 2808

FIX FERRETERÍAS

AV. CENTRAL SUR #27, COL. CENTRO, C.P. 30700,

TAPACHULA, CHIS. TEL.: 962 118 4083

SUCURSAL CHIHUAHUA

AV. SILVESTRE TERRAZAS #128-11, PARQUE INDUSTRIAL

BAFAR, CARRETERA MÉXICO CUAUHTÉMOC, C.P. 31415,

CHIHUAHUA, CHIH. TEL. 614 434 0052

FIX FERRETERÍAS

EL MONSTRUO DE CORREGIDORA, CORREGIDORA # 22,

COL. CENTRO, C.P. 06060, CUAUHTÉMOC, CDMX.

TEL: 55 5522 5031 / 5522 4861

SUCURSAL TORREÓN

CALLE METAL MECÁNICA #280, PARQUE INDUSTRIAL

ORIENTE, C.P. 27278, TORREÓN, COAH.

TEL.: 871 209 68 23

BOMBAS Y MOTORES BYMTESA DE MANZANILLO

BLVD. MIGUEL DE LA MADRID #190, COL. 16 DE

SEPTIEMBRE, C.P. 28239, MANZANILLO, COL.

TEL.: 314 332 1986 / 332 8013

TORNILLOS ÁGUILA, S.A. DE C.V.

MAZURIO #200, COL. LUIS ECHEVERRÍA, DURANGO,

DGO.TEL.: 618 817 1946 / 618 818 2844

SUCURSAL CENTRO JILOTEPEC

AV. PARQUE INDUSTRIAL #1-A, JILOTEPEC, C.P. 54240,

JILOTEPEC, EDO. DE MÉX.

TEL: 761 782 9101 EXT. 5728 Y 5102

CÍA. FERRETERA NUEVO MUNDO S.A. DE C.V.

AV. MÉXICO - JAPÓN #225, CD. INDUSTRIAL, C.P. 38010,

CELAYA, GTO. TEL.: 461 617 7578 / 79 / 80 / 88

CENTRO DE SERVICIO ECLIPSE

CALLE PRINCIPAL MZ.1 LT. 1, COL. SANTA FE, C.P. 39010,

CHILPANCINGO, GRO. TEL.: (747) 478 5793

FERREPRECIOS S.A. DE C.V.

LIBERTAD ORIENTE #304 LOCAL 30, INTERIOR DE PASAJE

ROBLEDO, COL. CENTRO, C.P. 43600, TULANCINGO,

HGO. TEL.: 775 753 6615 / 775 753 6616

SUCURSAL GUADALAJARA

AV. ADOLFO B. HORN # 6800, COL: SANTA CRUZ DEL

VALLE, C.P.: 45655, TLAJOMULCO DE ZUÑIGA, JAL.

TEL.: 33 3606 5285 AL 90

FIX FERRETERÍAS

AV. PASEO DE LA REPÚBLICA #3140-A, COL.

EX-HACIENDA DE LA HUERTA, C.P. 58050, MORELIA,

MICH. TEL.: 443 334 6858

FIX FERRETERÍAS

CAPITÁN ANZURES #95, ESQ. JOSÉ PERDIZ, COL.

CENTRO, C.P. 62740, CUAUTLA, MOR.

TEL.: 735 352 8931

HERRAMIENTAS DE TEPIC

MAZATLAN #117, COL. CENTRO, C.P. 63000, TEPIC, NAY.

TEL.: 311 258 0540

SUCURSAL MONTERREY

CARRETERA LAREDO #300, 1B MONTERREY PARKS

COLONIA PUERTA DE ANÁHUAC, C. P. 66052, ESCOBEDO,

NUEVO LEÓN, N.L. TEL.: 81 8352 8791 / 81 8352 8790

FIX FERRETERÍAS

AV. 20 DE NOVIEMBRE #910, COL. CENTRO, C.P. 68300,

TUXTEPEC, OAX. TEL.: 287 106 3092

SUCURSAL PUEBLA

AV PERIFÉRICO #2-A, SAN LORENZO ALMECATLA,

C.P. 72710, CUAUTLACINGO, PUE.

TEL.: 222 282 8282 / 84 / 85 / 86

ARU HERRAMIENTAS S.A DE C.V.

AV. PUERTO DE VERACRUZ #110, COL. RANCHO DE

ENMEDIO, C.P. 76842, SAN JUAN DEL RÍO, QRO.

TEL.: (427) 268 4544

FIX FERRETERÍAS

CARRETERA FEDERAL MZ. 46 LT. 3 LOCAL 2, COL EJIDAL,

C.P. 77710 PLAYA DEL CARMEN, Q.R.

TEL. 984 267 3140

FIX FERRETERÍAS

AV. UNIVERSIDAD #1850, COL. EL PASEO, C.P. 78320,

SAN LUIS POTOSÍ, S.L.P. TEL.: 444 822 4341

SUCURSAL CULIACÁN

AV. JESÚS KUMATE SUR #4301, COL. HACIENDA DE LA

MORA, C.P. 80143, CULIACÁN, SIN.

TEL.: 667 173 9139 / 173 8400

FIX FERRETERÍAS

CALLE 5 DE FEBRERO #517, SUR LT. 25 MZ. 10, COL.

CENTRO, C.P. 85000, CD. OBREGÓN, SON.

TEL.: 644 413 2392

SUCURSAL VILLAHERMOSA

CALLE HELIO LOTES 1, 2 Y 3 MZ. #1, COL. INDUSTRIAL,

2A ETAPA, C.P. 86010, VILLAHERMOSA, TAB.

TEL.: 993 353 7244

VM ORINGS Y REFACCIONES

CALLE ROSITA #527 ENTRE 20 DE NOVIEMBRE Y GRAL.

RODRÍGUEZ, FRACC. REYNOSA, C.P. 88780, REYNOSA,

TAMS. TEL.: 899 926 7552

SERVICIOS Y HERRAMIENTAS INDUSTRIALES

PABLO SIDAR #132, COL . BARRIO DE SAN BARTOLOMÉ,

C.P. 90970, SAN PABLO DEL MONTE, TLAX.

TEL.: 222 271 7502

LA CASA DISTRIBUIDORA TRUPER

BLVD. PRIMAVERA. ESQ. HORTENSIA S/N, COL.

PRIMAVERA C.P. 93308, POZA RICA, VER.

TEL.: 782 823 8100 / 826 8484

SUCURSAL MÉRIDA

CALLE 33 #600 Y 602, LOCALIDAD ITZINCAB Y MULSAY,

MPIO. UMÁN, C.P. 97390, MÉRIDA, YUC.

TEL.: 999 912 2451

NUEVO LEÓN

OAXACA

PUEBLA

QUERÉTARO

QUINTANA ROO

SAN LUIS

POTOSÍ

SINALOA

SONORA

TABASCO

TAMAULIPAS

TLAXCALA

VERACRUZ

YUCATÁN

This manual suits for next models

Table of contents

Other PRETUL Sander manuals

PRETUL

PRETUL PULA-P User manual

Popular Sander manuals by other brands

Oliver

Oliver 6305 owner's manual

Jet

Jet 22-44 Pro-3 Operating instructions and parts manual

Makita

Makita M9204 technical information

Makita

Makita M9204 instruction manual

Craftsman

Craftsman 351.215131 Operator's manual

Clarke

Clarke Woodworker CBS1-5B Operation & maintenance instructions

Chicago Pneumatic

Chicago Pneumatic CP9778 Operator's manual

Nitto Kohki

Nitto Kohki BB-20 instruction manual

Ferm

Ferm FEOS-135 user manual

Unior

Unior 1510 Operating instruction

stayer

stayer ls1200 operating instructions

Jet

Jet JSG-96 Operating instructions and parts manual

Parkside

Parkside PDS 290 B2 Operation and safety notes

Status

Status XPA Series Original instructions

Clarke

Clarke EZ Sand Operator's manual

Craftsman

Craftsman 113.22521 owner's manual

Craftsman

Craftsman 113.225831 owner's manual

CLAS

CLAS OP 1429 manual