Premium PRN165DX User manual
PRN165DX
PRN185DX
Model:
This product is for domestic use only
Use & Care Manual
Important Safeguards
Manual de uso ycuidado
Precauciones importantes
Este producto es para uso domestico unicamente
EXHIBIDOR VERTICAL
VERTICAL
REFRIGERATOR
DISPLAY
PRN165DX
PRN185DX
Modelo:
1
Dear Consumers：
Thank you for purchasing our products very much. In order to ensure
your safety and achieve the best using effect,please read this instruction
carefully.
INSTALLATION & OPERATION
IMPORTANT!!! PLEASE READ BEFORE
INSTALLATION
■If the unit has recently been transported, please let unit stand still for a
minimum of 24 hours before plugging it in.
■Make sure that the unit drops down to the desired temperature before
loading the unit with product.
■Make sure that there is proper ventilation around the unit in the area
where it will operate.
■Make sure all accessories are installed (i.e. shelves, shelf clips, casters)
before plugging the unit in.
■Please read through the Operation / Owner’s Manual in its entirety
before installation.
2
■Shelf installation
A. Hook shelf clips onto clip hanger
B. Place shelves on shelf clips making sure all corners are seated properly
C. Hook the plastic frame of price tag on shelves
Remove the glass door bracket from the door before use
3
■Casters or adjustable feet are available for the units
-- Universal caster with support）
-- Universal caster
ELECTRICAL
■Please ensure that the required voltage of the compressor is being
supplied at all times
CAUTION: Low or high voltage can detrimentally affect the refrigeration
unit.
■All units should be plugged into a grounded and properly-sized
electrical outlet with appropriate surge protection. Please refer to the
electrical requirement on the nameplate.
If you do not have the right outlet, have a certified electrician install the correct
power source.
■Please make sure that your unit has its own dedicated outlet. Do not
use an extension cord.
After proper installation, please plug the cord and turn on the power switch.
4
Temperature controller operation instructions
Setting the set point (desired temperature value)
To display or set the set point, proceed as follows:
1) Press SET for 1s, the set value will start flashing ;
2) Increase or decrease the value by per click ;
3) Press the SET button again to confirm the new value.
TROUBLE SHOOTING
Before requesting any service on your unit, please check the following points.
Please note that this guide serves only as a reference for solutions to common
problems.
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
Compressor not
running.
Fuse blown or circuit breaker tripped.
Power cord unplugged.
Thermostat set too high.
Cabinet in defrost cycle.
Replace fuse or reset circuit breaker.
Plug in power cord.
Set thermostat to lower temperature.
Wait for defrost cycle to finish.
Condensing
unit runs for
Excessive amount of warm product placed in
cabinet.
Allow adequate time for product to cool
down.
5
long periods of
time.
Prolonged door opening or door ajar.
Door gasket(s) not sealing properly.
Dirty condenser coil.
Evaporator coil iced over.
Ensure doors are closed when not in
use. Avoid opening doors for long
periods of time.
Ensure gaskets are snapped in
completely. Remove gasket and wash
with soap and water.
Check condition of gasket and replace
if necessary.
Clean the condenser coil.
Unplug unit and allow coil to defrost.
Make sure thermostat is not set too
cold. Ensure that door gasket(s) are
sealing properly.
Cabinet
temperature is
too warm.
Thermostat set too warm.
Blocking air flow.
Excessive amount of warm product placed in
cabinet.
Fuse blown or circuit breaker tripped.
Dirty condenser coil.
Prolonged door opening or door ajar.
Evaporator coil iced over.
Set thermostat to lower temperature.
Re-arrange product to allow for proper
air flow. Make sure there are at least
four inches of clearance from
evaporator.
Allow adequate time for product to cool
down.
Replace fuse or reset circuit breaker.
Clean the condenser coil.
Ensure doors are closed when not in
use. Avoid opening doors for long
periods of time.
(see above)
Cabinet is
noisy.
Loose part(s).
Tubing vibration.
Locate and tighten loose part(s).
Ensure tubing is free from contact with
other tubing or components.
6
Estimado Cliente,
Muchas gracias por adquirir nuestros productos.
Con fin de asegurarse de que la seguridad y lograr el mejor efecto
utilizando, por favor lea cuidadosamente este manual de instrucción
INSTALACION / OPERACION
IMPORTANTE! FAVOR LEER ANTES DE LA INSTALACION
■Si la unidad ha sido transportada recientemente, por favor, permita que
la unidad este inmóvil por un mínimo de 24 horas antes de conectarla.
■Asegúrese de que la unidad llegue a la temperatura deseada antes de
cargar la unidad con el producto.
■Asegúrese de que existe una ventilación adecuada alrededor de la
unidad en la zona donde operará.
■Asegúrese de que todos los accesorios están instalados (por ejemplo,
estantes, abrazaderas de repisa, ruedas) antes de enchufar la unidad.
■Por favor, lea el Manual de Operación / Manual del Propietario en su
totalidad antes de la instalación.
7
■Instalación de los estantes
A. Enganche las abrazaderas en el colgador para tramos
B. Coloque los estantes sobre los ganchos correspondientes, asegurándose
que todas las esquinas quedan debidamente asentadas
C. Enganche el marco plástico para etiquetas de precio en los estantes.
Retire el soporte de la puerta de cristal de la puerta antes de su uso
8
■Están disponibles ruedas o pies ajustables para la unidades
-- Pies ajustables
-- Rueda con frenos
ELECTRICIDAD
■Por favor, asegúrese que el voltaje requerido del compresor está
siendo alimentado en todo momento
ATENCION: Una tensión baja o alta puede afectar negativamente la
unidad de refrigeración.
■Todas las unidades deben enchufarse en un tomacorriente
conectado a tierra y correctamente dimensionado con protección
contra sobretensiones eléctricas. Consulte los requisitos
eléctricos en la placa de características.
9
Si no tiene la salida correcta, haga que un electricista certificado instale la
fuente de alimentación correcta.
■Por favor, asegúrese de que su unidad tiene su propia toma de
corriente dedicada. No utilice un cable de extensión.
Después de la instalación, conecte el cable y encienda el interruptor de
alimentación.
Instrucciones del control de temperatura
Ajuste de temperatura (valor deseado)
Para mostrar o establecer el punto de ajuste, proceda como sigue:
1) Pulse SET por 1s, el valor comenzará a parpadear;
2) Aumente o disminuya el valor por clic;
3) Pulse el botón SET para confirmar el nuevo valor.
This manual suits for next models
1
Table of contents
Languages:
Other Premium Refrigerator manuals
Premium
Premium PRN435MW User manual
Premium
Premium PRN12150MW User manual
Premium
Premium PRF31500MW User manual
Premium
Premium PRN438HW/S User manual
Premium
Premium PRF735HW User manual
Premium
Premium PRN438HW User manual
Premium
Premium PRF24600MS User manual
Premium
Premium PRF200LW User manual
Premium
Premium PRN10050MW User manual
Premium
Premium PRF200LW User manual
Premium
Premium PRF047XW User manual
Premium
Premium PRF1660MS User manual
Premium
Premium PRF33600MS User manual
Premium
Premium PRN10050MW User manual
Premium
Premium PRF315MW User manual
Premium
Premium PRF185MW User manual
Premium
Premium PRN436MS User manual
Premium
Premium PRN4560MS User manual
Premium
Premium PRN995MW User manual
Premium
Premium PRN10050MW User manual
