A. SET-UP
1. BoIt the legs to the cabinet.
2. Lift liqhtbox int,o an uPright
- nosítioñ. Be sure none of the cables
ãre crinped in bet¡¡een the lightbox
and cabinet.
3. Ensaqe the snap in the rear of the
rién€,uox to thê cabinet-
4, To remove the llÇhtbox backglass and
oain servicing access to the
éIectronics páne1 and the lnsert lamp
assembly, proceed as follows:
UNLOCK lHE LIGHTBOX BY TURNING THE KEY
À QUARTER TURN CLOCKWISE.
LIFT UP THA BACKGLASS RETAINING BOTTOM
TRrl,t ABOUÎ 3 | Att To CLEAR THE rrHrr
RETAINING CHANNEL ON THE TOP EDGE OF
THE DrSPLÀY/SPEAKER PÀNEL, PrVOT OUT
TOWÀRDS YOU AND SLIDE THE BÀCKGLÀSS
DOI{N ÀND OUT, CAREFULLY SET ÀSrDE.
REMOVE THE nHrr RETATNING CHÀNNEL, SLIDE
THE PLEXIGI,ASS INSERT UP ÀND OUT' SLIDE
UP ÀND REMOVE THE DISPLAY/SPEAKER PANEL
ÀND LAY FACE DOWN ON THE CABINET.
UNLOOSEN THE TWO ÍIING NUTS ON THE LEFÎ
SIDE AND PUSH THE LOCK SLIDE UPI'TARDS,
THIS AI,I,OWS THE LIGHTBOX I.,ÀMP INSERT TO
SWING OUI ÀND FOR GÀINING ÀCCESS TO THE
ELECTRONICS PANEL.
5. Secure the ltghtbox to the cablnet
wlth the bolts and washers provlded.
TO REPLACE THE BACKGLASS, INSERT THE
DISPLAY/SPEÀKER PÀNEL, ENSURE THAT THE
METÀL TABS ON THE PANEL MATE INTO THE
I{OOD RETAINERS, SLIDE IN THE PIJEXIGLASS
PÀNEL AND INSERT THE IIHII RETAINING
CHANNEL.
SLIDE THE BACKGI,ASS UP INTO THE
I,IGHTBOX, PIVOT INWARDS AND SLTDE DOWN
INTO THE IIHII CHÀNNEL, TURN THE KEY A
QUÀRTER TURN COT]NTER.CLOCKWISE TO LOCK
THE LIGHTBOX.
6the cabinet door and loosen the
rnoulding locklng arrn.
7. Remove the front noulding from the
cabinet.
I. INSTALLATTON
hotd in place and insert the ProP
st,ick into the countersunk hole on
the underside of the P1aYfield.
CÀUTION!
Use prop stick when servicing under
the playfield.
lO.Unravel and straighten out the power
line cord located at the rear of the
cabinet.
ll.Proceed to rrB. CHECK-OUT||.
8. Slide the playfÍeld glass toward you
and remove it, carefull-y set aside.
9. Raise the playboard and pivot it
upwards anä uãcr towards- the lightbox,
B. CHECK-OUT
1. check that all cables are clear of
noving parts.
2. check for any loose wires.
3. Check switches for loose solder or
other foreign matter.
4. Be certaÍn alt fuses are fírmly seated.
5. Check transformer for any foreign
matter across terrninals.
6. Be sure that the Transformer Panel
porder input connector À12J5 r - .
õorrespoñds to the supply voltage.
7. Check the setting of the normally
oÞen tilt switch-on the underside of
the plavfield. One blade should be
free'-flôating with a weight on the
end.
8. The plu¡nb-bob tilt can be adjusted by
Ioosêning the clip and.raising the
r¡tumb-bob to increase its
^sensitivity, or lowering it to
decrease its sensitivitY.
g. Lower the playfield into the cabinet.
Using the Leg adjusters, l-eveÌ t'he
playfield and set the Pitch.
Recommended pitch is 6o. For
alternate settÍngs, see illustration
on facing page.
lO.PIug the line-cord into a properly
grounded 3-wire recePtacle ONLY!
ll.Refer to Section IIf to make all
necessary game adjustnents.
12.Re-install the playfield glass,
front moulding and lock the
cabinet door.
I3.CAUTION! If this game has been
suÐæd to extrerne cold, allow to
warm up to room tenPerature.
Open
front
il
