PRASTEL MT15000/2 Owner's manual

Technical Instructions

MT15000/2

MT15000/2-M

MT15000/2 – V1.0 ENGLISH

p.2/11

PRASTEL France SARL

ZI Athélia II, 225 Impasse du Serpolet, 13704 LA CIOTAT Cedex, France

Tel : +33.442.98.06.06 – Fax : +33.442.04.53.51 – infos@prastelfrance.fr

CONTENTS

Information and Recommendations................................................................................................3

Specifications....................................................................................................................................3

1) MT15000/2 .....................................

2) MT15000/2-M .................................

3) PROTECTION................................

Wiegand or data clock device connection.....................................................................................4

MT15000/EXT4 and MT15000/EXT4-M extension modules connection ......................................5

Connecting a fail-safe electric strike and electro magnet............................................................6

Connecting a standard strike ..........................................................................................................7

MT15000/2 control unit connection to Ethernet network..............................................................8

SWAMIGO3 dongle installation .......................................................................................................9

Terminal block features..................................................................................................................10

"Reset" buttons use........................................................................................................................11

Dear Customer,

You have purchased a MT15000/2 control unit produced by PRASTEL France.

We thank you for your interest in our products and wish you all the best with the installation procedure.

PRASTEL France

MT15000/2 – V1.0 ENGLISH

p.3/11

PRASTEL France SARL

ZI Athélia II, 225 Impasse du Serpolet, 13704 LA CIOTAT Cedex, France

Tel : +33.442.98.06.06 – Fax : +33.442.04.53.51 – infos@prastelfrance.fr

INFORMATION AND RECOMMENDATIONS

In accordance with UTE C00-200 European Directive describing Directives 89/336CEE and 92/31 EEC,

MT15000/2 complies with the following standards:

- NF EN 50081-1 on electromagnetic emissions and

- NF EN 50082-1 on electromagnetic sensitivity.

Wiring recommendations: the cables used to connect readers, network and other devices must be installed in

accordance with the instructions for Level 2, as set forth in standard NF EN 61000-4-4 (protected environment).

This product must be installed by a qualified company. Inappropriate installation and use may entail a risk of

electric shock or fire. Please read these technical instructions before installing the product and follow assembly

instructions thereof.

All internal capacitors in the 220V version will lose charge at a healthy level after 60 seconds once power

has been turned off, under normal conditions. However, in the event of a failure, the charge may be main-

tained for much longer and adequate precautions are required before using the product.

SPECIFICATIONS

1) MT15000/2

Maximum consumption............................... 300 Ma

Power voltage ............................................. 9 – 14VDC

Weight ........................................................ 150 g

Dimensions.................................................157 x 108 x 30 mm

Operating temperature................................ - 20°C to + 50°C

Relay outputs.............................................. 1A / 12V – 1A / 24V

2) MT15000/2-M

Weight, with housing...................................4 Kg

Housing dimensions ...................................330 x 330 x 90 mm

Operating temperature................................ - 20°C to + 50°C

Integrated 220V power supply:

Output voltage............................................. 12V

Maximum output current............................. 5A

Battery connection...................................... 13,6V

3) PROTECTION

The control unit is fitted with a fuse on 12V input inside the housing. Check the fuse if the power LED does not light

up when the module is under power.

MT15000/2 – V1.0 ENGLISH

p.4/11

PRASTEL France SARL

ZI Athélia II, 225 Impasse du Serpolet, 13704 LA CIOTAT Cedex, France

Tel : +33.442.98.06.06 – Fax : +33.442.04.53.51 – infos@prastelfrance.fr

WIEGAND OR DATA CLOCK PROTOCOL DEVICE CONNECTION

Information :

5 wires (3 pairs recommended)

Max distance : 100m

Cable type : 0,6mm (SYT advised)

Screen : Optional

Warning

Do not connect the jumper wires near other high voltage or current cables, including 220V and higher.

Note:

Each reader may support a separate technology

Example: Reader 1 in Wiegand, Reader 2 in Data Clock

WIEGAND :

o proximity reader

(PRASTEL, HID, STID, INDALA, …)

o keypad (PRASTEL, XPR, …)

o Biometric readers (PRASTEL, …)

o Radio receivers (PRASTEL, …)

o DALLAS (via interface)

DATA CLOCK :

o Magnetic strip readers

o Bar codes readers

o Proximity reader

o Radio receivers

Warning

If you use an external power supply for your

proximity readers, please be sure to connect

all different masses with the one on the

control unit.

MT15000/2 – V1.0 ENGLISH

p.5/11

PRASTEL France SARL

ZI Athélia II, 225 Impasse du Serpolet, 13704 LA CIOTAT Cedex, France

Tel : +33.442.98.06.06 – Fax : +33.442.04.53.51 – infos@prastelfrance.fr

MT15000/EXT4 AND MT15000/EXT4-M EXTENSION MODULES CONNECTION

MT15000/2

MT15000/EXT4

A A

B B

You may also use A and B terminal blocks on MT15000/EXT4 modules to connect your RS485 bus.

Information

2 wires (2 pairs recommended)

Max. Distance: 750m

Cable Type: 0.6 mm (SYT recommended)

Warning

Do not connect the wires near other high voltage or current cables, including 220V and higher. Make sure to use

the same pair for wires A and B.

Up to 10

modules per

MT15000/2 RS485

MT15000/2 – V1.0 ENGLISH

p.6/11

PRASTEL France SARL

ZI Athélia II, 225 Impasse du Serpolet, 13704 LA CIOTAT Cedex, France

Tel : +33.442.98.06.06 – Fax : +33.442.04.53.51 – infos@prastelfrance.fr

CONNECTING A FAIL-SAFE ELECTRIC STRIKE AND AN ELECTRO MAGNET

(electric stike and electro magnet remain operational when not receiving power)

Warning

The anti-reverse diodes delivered with the control unit must be used and connected as shown in the above wiring

diagram in order to avoid any unpredictable malfunctions caused by back-currents that might disturb the system’s

appropriate performance.

The above wiring diagram must be followed even when using an additional backup power supply for locking, which

is separate to the control unit power supply.

Power supply

+12V 0V

Diode

MT15000/2 – V1.0 ENGLISH

p.7/11

PRASTEL France SARL

ZI Athélia II, 225 Impasse du Serpolet, 13704 LA CIOTAT Cedex, France

Tel : +33.442.98.06.06 – Fax : +33.442.04.53.51 – infos@prastelfrance.fr

CONNECTING A STANDARD STRIKE

Warning

The anti-reverse diodes delivered with the control unit must be used and connected as shown in the above wiring

diagram in order to avoid any unpredictable malfunctions caused by back-currents that might disturb the system’s

appropriate performance.

The above wiring diagram must be followed even when using an additional backup power supply for locking, which

is separate to the control unit power supply.

Diode

Power supply

+12V 0V

MT15000/2 – V1.0 ENGLISH

p.8/11

PRASTEL France SARL

ZI Athélia II, 225 Impasse du Serpolet, 13704 LA CIOTAT Cedex, France

Tel : +33.442.98.06.06 – Fax : +33.442.04.53.51 – infos@prastelfrance.fr

MT15000/2 AND MT15000/2-M CONTROL UNIT CONNECTION TO ETHERNET NETWORK

Every MT15000/2 control unit has an IP address. This address is indicated on sticker on the control unit casing.

To set a different IP address, you can use the menu "automatic detection" of SWAMIGO3.

For that purpose, proceed as follows:

•After creating the installation, at the first launch, SWAMIGO3 suggests to create a new control unit

•Click « Search »

•A list of all the detected control units appears

•Double-click on the control unit you wish to add to the installation

•Check in the devices status that your control unit is connected.

Crossed cable

Straight

cable

Straight

cabl

MT15000/2 – V1.0 ENGLISH

p.9/11

PRASTEL France SARL

ZI Athélia II, 225 Impasse du Serpolet, 13704 LA CIOTAT Cedex, France

Tel : +33.442.98.06.06 – Fax : +33.442.04.53.51 – infos@prastelfrance.fr

SWAMIGO3 DONGLE INSTALLATION

To use SWAMIGO3 software, you may need, according to the site specifications (see following board), to install a

dongle on your control unit.

Dongle use :

Readers installed on site Software Dongle

Up to 2 readers SWAMIGO3 LIGHT No dongle required

Up to 10 readers SWAMIGO3-10 Dongle required

Up to 40 readers SWAMIGO3-40 Dongle required

Up to 140 readers SWAMIGO3-140 Dongle required

Up to 840 readers SWAMIGO3-840 Dongle required

Dongle installation : While power supply is turned off, install the dongle proceeding as follows :

To check if system is running regularly, SWAMIGO3 indicates the version you are using at the bottom of the main

window. The control unit must be connected so that the dongle can be identified.

If you haven’t installed the right dongle according to your installation, control units will show in the devices status

but no update and no events reports will be possible.

MT15000/2 – V1.0 ENGLISH

p.10/11

PRASTEL France SARL

ZI Athélia II, 225 Impasse du Serpolet, 13704 LA CIOTAT Cedex, France

Tel : +33.442.98.06.06 – Fax : +33.442.04.53.51 – infos@prastelfrance.fr

TERMINAL BLOCK FEATURES

This manual suits for next models

Table of contents

Other PRASTEL Control Unit manuals

PRASTEL

PRASTEL DOM1-L1SIM User manual

PRASTEL

PRASTEL SER30E User manual

PRASTEL

PRASTEL MT15000/EXT-IO Owner's manual

PRASTEL

PRASTEL M1000E User manual

PRASTEL

PRASTEL M1000 User manual

PRASTEL

PRASTEL CNCR EURO/SER User manual

PRASTEL

PRASTEL EASY-PAD User manual

PRASTEL

PRASTEL UNIK2E-V2 Technical document

PRASTEL

PRASTEL GT+ User manual

PRASTEL

PRASTEL FSTYLE25A User manual

PRASTEL

PRASTEL UNIK3I-V4 Safety guide

PRASTEL

PRASTEL UNIK1E User manual

PRASTEL

PRASTEL M2000PE User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual