PR Lighting CSL 1037 User manual

CSL 1037

PR-3206D

This product manual contains important information about the safe installation and use of this unit. Please

read and follow these instructions carefully and keep this manual in a safe place for future reference.

PR LIGHTING LTD.

http://www.pr-lighting.com

2/14

INDEX

SAFE USAGE OF THE UNIT 3

INSTALLING THE UNIT

POWER SUPPLY-MAINS 4

CONTROLCONNECTION 6

DMX TERMINATOR 7

SETUP OPTIONS-UNIT CONFIGURATION 7

TO SETTHE DMX STARTADDRESS 8

OPERATION MENU 8

DMX PROTOCOL 8

MAINTENANCE 9

TROUBLESHOOTING 9

TECHNICALDATA 10

ELECTRICALDIAGRAM 12

COMPONENT ORDER CODES 13

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to

change without notice. Whilst every care is taken in the preparation of this manual we reserve the right to change

specifications in the course of product improvement. The publishers cannot be held responsible for the accuracy of the

information herein, or any consequence arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the

unit are in good condition before installation and use. Should there be any damage caused by transportation, consult

your dealer and do not use the unit. Any damage caused by improper use will not be assumed by the manufacturer and

/ or dealer.

ACCESSORIES

These items are packed together with the unit:

Name Quantity Unit Remark

Barn Door 1 Pc

Clamp 1 Pc

Safety Cord 1 Pc

XLR Cable 1 Pc With male and female sockets

Power Cord 1 Pc

User’s Manual 1 Pc

When unpa

any damage

The unit ca

with water o

The unit is n

The unit is o

Do not proj

Avoid direct

Do not atte

Electrical co

Before insta

It is essentia

Do not conn

Make sure t

Only handle

When the u

fixing for sa

Exterior sur

There is no

If any questi

Alwa

maintena

king and befo

caused by tran

only used

other liquids.

t designed or

ly intended fo

ct the beam on

exposure to th

pt to dismantl

nection must

lation, ensure t

that each unit

his device

at the powe

the powe

-cor

is hanged t

ety seasons. F

ace temperatur

ser serviceabl

ns, don’t hesit

isconnectio

ce work !

e disposing o

portation, con

ndoors, IP20.

ntended to be

installation, o

o inflammable

light from the

and/or modif

nly be carried

at the voltage

s correctly eart

o any other ty

ord is never cr

by the plug.

a high place,

r details, refer

s of the unit a

parts inside th

te to consult y

from th

AFE U

the carton, ch

ult your dealer

he fixture sho

ounted directl

eration and m

surfaces, mini

lamp. The ligh

the unit in any

ut by qualifie

nd frequency

ed and that el

es of dimmer

mped or dam

ever pull out t

lease use a s

o “INSTALL

er 5 minutes’

unit, do not o

ur dealer or

power, w

3/14

AGE OF

ck there is no

and do not use

ld be kept in

on to inflam

intenance by

um distance i

is harmful to

way.

personnel.

f power suppl

ctrical installat

paratus.

ged by sharp e

e plug by

ugg

fety cord prov

HE UNIT “se

peration is 45

℃

en the housin

anufacturer.

en the de

THE UN

ransportation

the apparatus.

ry place with

able surfaces.

ualified person

2m. 2m

yes.

match the po

on conforms t

ges. Never le

ng the powe

ded to pass th

tion.

℃

, when achie

and never ope

ice is not

amage before

ut excessive d

el.

er requireme

all relevant st

the power-cord

ord.

ough the unit’

ing steady stat

ate the unit wi

in use or

using the unit.

mpness, heat,

ts of the unit.

ndards.

comeinto conta

support as a

it is 60℃.

h the covers re

efore clea

Should there

dust and conta

twithothercabl

econdary safe

oved.

or an

4/14

INSTALLTHE UNIT

Safety Cord Clamp

Knob

Barn Door

The fixture works while being hung. Its head can be manually rotated with the range of 240 degrees. Before moving the head, loosen the

two angle-knobs.After the head is at the angle desired, tighten the two knobs.

Take 1 clamp and 1 safety cord out from the package and mount 1 clamp on the axis of the support with 1 retainer. Hang the fixture on

the structure and fasten the screws attached to the clamp. Always ensure that the fixture is firmly anchored to avoid vibration

and slipping whilst functioning. Always ensure that the structure to which you are attaching the unit to is secure and

strong enough to support the weight of the fixture. For safety the unit should have a secondary fixing with a safety

cord through the support of the unit to ensure safe mounting.

Warning:

1. Clamp is only used for installation. The unit MUST be lifted or carried via supporting frame instead of clamps.

2. For safety the safety cord should afford 10 times of the unit’s weight

5/14

POWER SUPPLY-MAINS

Connect the power cord as follows:

L (live) =brown

E (earth) =yellow/green

N (neutral) =blue

Before connection with mains power, make sure that the voltage and frequency marked on the rating plate of the projector match what

are supplied. It is recommended that each projector be supplied separately so that they may be individually switched on and off.

Note: If some fixtures are connected in series via POWER INs and POWER OUTs, connect the POWER IN of the first fixture with

external power and connect its POWER OUT with the POWER IN of the second fixture and so on till all the fixtures are connected.If

the voltage is 200V~240V, 12pcs can be connected at maximum. If the voltage is 100V~120V, the maximum is 6pcs. The diameter of

the core of the wire of the XLR cable should be equal or bigger than 2.5mm2

IMPORTANT

It is essential that each fixture is correctly earthed(yellow/green twin wire) and the electrical installation conforms to all

relevant standards.

POWER POWER OUTPOWER IN POWER OUTPOWER IN POWER OUTPOWER IN

6/14

CONTROL CONNECTION

4N/C

N/C

PIN FUNCTION

GND

3DATA+

DATA-2

DMX 512

5 PIN

DMX IN

DMX OUT

Connection between the controller and a unit and between one unit and another must be made with a 2 core-screened cable, with each

core having at least a 0.5mm diameter. Please use the unit’s cannon 5- pin signal input and output cables as connection. The 5-pin

signal connections are connected as shown in the figure above.

Note: Care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of the plug is not

connected in any way. The unit accepts digital control signals in protocol DMX512 (1990).

The maximum of units in parallel for operation is 32 pcs. Connect the controller’s output to the first fixture’s input using 5-pin XLR

cable, and connect the first fixture’s output to the second fixture’s input and connect the rest fixtures in the same way. Eventually

connect the last fixture’s output to a DMX terminator as shown in the figure below. Note: for synchronous control, the start addresses

of all slaves should be same.

Each unit should be connected to power supply individually and the voltage and frequency of the power supply should match those

indicated on nameplate.

DMX OUT

DMX IN TERMINOTER

DMX IN

DMX OUTDMX IN FROM

CONTROLLER

7/14

DMX TERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents

electrical noise from disturbing and corrupting the DMX control signals.

The DMX terminator is simply an XLR connector with a 120Ω(ohm) resistor connected across pins 2 and 3, which is then plugged

into the output socket on the last unit in the chain. The connections are illustrated below.

SETUPOPTIONS-UNIT CONFIGURATION

Press the buttoms gentally to set the DMX address and other settings.

To browse through or change configurations, press ENTER button for about 3s to unlock the digtial display. The display will

show its menus. Each main menu has its own sub-menus. And each menus stands for designated funciton. For details, pleaes

refer to “Opertaion Menu” hereinafter.

To set or browse through funtions or settings , pess FUNC button.

Press buttonENTER to save changes or enter into sub-menus. Press buttoms UP or DOWM to change numbers(plus or

minus)

PressFUNC to go back to main menus or the upper level menus.

Afte the exit of the menus, the birghtness of the display is the one currently set .(the display’s range is between 0 and 255)

If DMX signal available, the display will show current DMX address

8/14

TO SET THE DMX STARTADDRESS

Each unit must be given a DMX start address so that the correct unit responds to the correct control signals. This DMX start address is

the channel number from which the unit starts to “listen” to the digital control information being sent out from the controller. The unit

has 2 DMX channels, so set the No. 1 unit’s address 001, No. 2 unit’s address 003, No. 3 unit’s address 005, and so on.

While the display is locked( initial stage of the display), press the FUNC for more than 3 seconds to unlock it,

Press FUNC to locate menu

Press ENTER to show DMX address

Press UP or DOWN to set or change parameters

While the set address is flashing, press ENTER to confirm. After this, the start address has been automatically stored. After

power-on next time, the latest number will be shown.

Press FUNC to go back t o1st level menus

Operations Menu

1ST Level menu 2nd level menu 3rd level menu Remarks

DMX Address（ADDR）

XXX

（DMX：001~512）

DMX Address

Configuration （CNFG）

Display settings（DISP）

（Default：ON）

(

)

Digital Display always

（OFF）

The digital display off

3 minutes after no

buttons are pressed

after the exit of the

menus

Dimme

（DIMM）

000-255

From Dark to Bri

Brightness Value

Displayed

Information （INFO）

Fixture’ s temperature

（TEM

）

XXX Fixture’s Temperature

Fixtur

’s hours （

IME）

XXXX Fixture’s use time

Software Version（VE

）

X.X.X Version Displayed

DMX PROTOCOL

CHANNEL FUNCTION DMX DESCRIPTION

1 Dimmer 000-255 From dark to bright

2 Strobe

000 - 007 NO strobe

008 - 255 Strobe speed from slow to fast

9/14

MAINTENANCE

To prolong the life of the unit, it is very important to do the maintenance work. If the unit is idle for a long time, damp, smoke or

particularly dirty surroundings can cause greater accumulation of dirt on its cover and housing. So it should be cleaned to maintain

an optimum light output and at the same time to prevent it from being corrupted by acid gas.

Cleaning frequency depends on the environment in which the fixture operates. Soft cloth and typical glass cleaning products should be

used for cleaning. It is recommended to clean unit at least once every 20 days.

Do not use any organic solvent, e.g. alcohol, to clean housing of the apparatus.

TROUBLESHOOTING

PROBLEM ACTION

The unit doesn’t switch on

¾Power connection is not correct.

¾Power supply is damaged or abnormal. Call a qualified personnel to fix

it.

¾Connection of control board is not correct. Call a qualified personnel to

fix it.

The unit can be turned on, but LEDs do not emit

light and are out of control.

¾Connection of LED board is not correct. Call a qualified personnel to fix

it.

The lamp comes on but the unit doesn’t respond

to the controller

¾Make sure that the unit is correctly configurated.

¾Replace or repair the DMX cable.

The beam appears dim ¾The unit is too hot.Take ventilation measures to make it cool.

10/14

TECHNICAL DATA

VOLTAGES:

100V~240V AC，50/60Hz

POWER CONSUMPTION:

330@220V

LED:

Power consumption 10W

Quantity 37pcs

CRI

5600K

Ra≥70

Manufacturers Rated LED Life 50000 Hours

DIMMER:

0-100% linearly adjustable

STROBE:

Electronic Strobe,0.3-20 F.P.S

BEAMANGLE:

FieldAngle (θ1/2 peak) 14.7°

CONTROL:

DMX512, 5pin interfaces

2Channels

OTHE FUNCTIONS:

Display of fixture’s hours

Display of software version

Display of LED lamp PCB’s temperature

Input signal isolation

LED over-temp protection

HOUSING:

High-intensity aluminum alloy, IP20

WORK ENVIRONMENTTEMPERATURE:

-20°C~40°C

WEIGHT:

7KG

Table of contents

Other PR Lighting Dj Equipment manuals

PR Lighting

PR Lighting PR-8242 User manual

PR Lighting

PR Lighting PILOT 300 User manual

PR Lighting

PR Lighting XLED 6007 User manual

PR Lighting

PR Lighting JNR PAR COB User manual

PR Lighting

PR Lighting XR 380 Beam User manual

PR Lighting

PR Lighting XPar 1012 User manual

PR Lighting

PR Lighting XR480 BEAM User manual

PR Lighting

PR Lighting XR 1700 FRAMING User manual

PR Lighting

PR Lighting AQUA 580 BEAM User manual

PR Lighting

PR Lighting LED Studio 3201D User manual

PR Lighting

PR Lighting XPar 348 User manual

PR Lighting

PR Lighting JUNIOR JNR-8146C User manual

PR Lighting

PR Lighting XR 1000 Framing User manual

PR Lighting

PR Lighting XLED 300 Beam User manual

PR Lighting

PR Lighting ARC LED 1054 User manual

PR Lighting

PR Lighting PR-8802 User manual

PR Lighting

PR Lighting Theatre Master PR-3010 User manual

PR Lighting

PR Lighting OMEGA User manual

PR Lighting

PR Lighting PR-8330 User manual

PR Lighting

PR Lighting AQUA LED 600 SPOT User manual

PR Lighting

PR Lighting XLED 6019 User manual

PR Lighting

PR Lighting XRLED 3000-W Framing User manual

PR Lighting

PR Lighting XPar 336-W User manual

PR Lighting

PR Lighting XR480S BWS User manual

Popular Dj Equipment manuals by other brands

ALPHA LITE

ALPHA LITE ALPHA 1500 User manual book

Chauvet

Chauvet OVATION E-930VW Quick reference guide

Zumtobel

Zumtobel APHRODITE Home Instructions for use

Snow Masters

Snow Masters Zig Oscillator user manual

EuroLite

EuroLite 50530554 user manual

Beamz

Beamz BUV243 user manual

thomann

thomann Stairville DJ Lase 40-G MK-III user manual

Eagletone

Eagletone 6 Eyes Flower user manual

EuroLite

EuroLite FLD-1508 user manual

Technical Pro

Technical Pro LG8xSEA user manual

JB Systems

JB Systems Lounge Laser DMX Operation manual

Lightmaxx

Lightmaxx Vega Halo 90 user manual

Elation

Elation FUZE WASH Z350 user manual

Maverick

Maverick MK3 WASH Quick reference guide

Infinity

Infinity TF-260C7 Fresnel manual

Chauvet

Chauvet EVE E-50Z Quick reference guide

Eliminator Lighting

Eliminator Lighting E 138 manual

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC user manual