PowerWalker VFI RT HID Series User manual

ENGLISH

Quick Guide

PowerWalker VFI RT HID Series

I. Assembly

The UPS can be assembled in a rack form using rack ears (Rack Mount Kit is not included) or in

tower form using tower holder. The LCD part can be taken out and turned 90 degrees to align

with orientation of the UPS.

Internal batteries are disconnected for transportation. It is necessary to open front panel (2

screws on the side, 1 screw behind the LCD) and connect the two available connectors before

first usage. External batteries are connected in front using third connector.

Details at https://support.powerwalker.com/kb/faq.php?id=83 (faq.powerwalker.com)

II. Display Panel

The LCD uses blue back-light as standard. In case of critical

error the back-light changes to red. Buttons react to:

Click – Press the button for around 1s and

release

Press – Press and hold for more than 3s, release

Press long – Press and hold for more than 10s,

release

Control

Button

Switch

Function

ON /

Alarm

Silence

Press to turn on the UPS.

Click to disable alarm buzzer (press during battery mode).

Press long to perform battery life test

OFF

Press to turn off the UPS. (UPS will switch to bypass if it is configured)

Click to disable alarm buzzer in bypass mode.

Press to release the UPS from fault mode or EPO status.

Select

Press the Select button to select the settings value one by one

Enter

Press to enter settings mode (depending on the UPS Mode)

Click to enter settings item (settings string will flash)

Click to confirm settings

Press to exit Settings mode

III. Description of LCD display function

No.

Description

Function

Input frequency and

voltage

Indicates the value of input frequency and voltage

Input plug indicator

Lights on when the input power is at no loss.

LCD Screen

ON Button/

Alarm Silence OFF-Button Select-Button Enter-Button

ENGLISH

Output frequency and

voltage

Indicates the value of output frequency and voltage

Output plug indicator

The UPS has two groups of outlets. The output plug

indicator will light on if there is output power

respectively.

UPS status/user setting

display String

Strings Indicate the UPS status( see Table 4)

Strings Indicate user setting options( see Table 5)

Warning indication

Lights on when the UPS is failure or alarm.

Settings

Lights on when the UPS under settings mode.

Battery volume level

display

Indicates the amount of battery volume remaining.

Each battery volume level bar indicates approximately

20% of total battery volume

Load Power level display

Indicates the load level of the UPS. Each level bar

indicates approximately 20% of the total UPS output

Power.

IV. Rear Panels

VFI 1000-1500-2000 RT

VFI 3000 RT

250V 10A 250V 10A

INTELLIGENT SLOT

RS232

LS2 AC OUTPUT

LS1 AC OUTPUT

250V 16A

USB

AC INPUT

DRY IN

EPO

DRY OUT

AC Output

ENGLISH

V. Connection of the UPS

The UPS should be protected with circuit breaker on the

input. Minimum rating should 10A for 1000VA, 12A for

1500VA, 16A for 2000VA and 20A for 3000VA. For output

connection please use original cables and share the load

equally among outlets.

VI. Connecting Battery Packs

Remove front panel, connect the battery via Anderson PP45 connectors. Make sure you

are connecting with correct polarity (red to red, black to black). Make sure the wires are

connected tight. Close front panel. Setup the amount of battery packs in the settings.

VII. Communication Ports

A Local communication with the software can be

established via USB or RS232 connector. Alternatively UPS

can be controlled using dry contacts.

VIII. DB9 Female (RS232) pin description

PIN #

Signal name

Function

Direction from the UPS

Transmit to external device

Out

Receive from external device

GND

Signal common (tied to chassis)

Not applicable

Other

Not Used

Dry contacts are not available for VI ERT series.

IX. Dry contact port and EPO

The relay output contact must not be connected to any utility connected circuits.

Reinforced insulation to the utility is required. The relay output contact has a maximum

rating of 30Vac/1A.

The signal input to control UPS On/Off status is the same as one button to control UPS

On/Off status. The relay output can be configured by protocol command:

Dry out signal

Description

Summary Alarm

[DEFAULT]

Activated when any warning happens

Dry contact input / EPO

USB Port

AC Input

Dry contact output

Intelligent Slot

RS232

Earth Line Port

ENGLISH

On Battery

Activated when the UPS operates on battery

Battery Low

Activated with the “bLOW” alarm

UPS ok

Activated when the UPS has no alarms and no fault.

On Bypass

Activated when the UPS has bypass output.

Dry in signal

Description

UPS On/Off

One second pulse activate, if active, the UPS turns off when UPS is

on inverter; the UPS turns on when UPS is not on inverter. It is the

same as a remote button to control UPS On/Off status.

For more information visit our website.

X. Extension Slot

UPS allows extending communication means by extension cards. Please check product

website for list of accessories.

XI. UPS Initial Startup

1. Verify that the internal batteries (behind front panel) and optional battery packs are

connected.

2. Plug the equipment (load), but do not turn it on

3. Plug in the UPS input power cord. The UPS front panel display illuminates and UPS

status display shows “INIT” for initialization and then settles on “STbY”

4. Press and hold the ON/OFF button more than 3 seconds. The UPS status display

changes to “LINE”

5. Configure the UPS (i.e. EBM battery settings)

At initial startup, the UPS sets system frequency according to input line frequency.

XII. User Setting String

Settings should be done in standby (no output) or bypass mode. Load Segments can be

also changed in Line Mode

LCD String

Description

Values

OPV

Output Voltage

208/220/230/240 (Volt)

OPF

Output Frequency

50/60 (Hz)

bYPA

Bypass Status

Enable (001) / Disable (000)

MOdE

Operating Mode

UPS/ECO/CVF

LS1 / LS2

Load Segments

On (001) / off (000)

EbM

External Battery Modules

0-9

XIII. [UPS] Normal Operating Mode

UPS works in normal double conversion mode, providing clean and filtered power.

XIV. [CVF] Frequency Converter Mode

When input frequency is within 40 Hz to 70 Hz, the UPS can be set at a constant output

frequency, 50 Hz or 60 Hz. The UPS will still charge battery under this mode. Frequency

Converter requires de-rating of the UPS Power to 70%.

XV. [ECO] Economy Mode

It is also referred to as high efficiency mode. The load is supplied directly from mains via

internal filter when input voltage is within the allowed range. If the input is abnormal,

UPS would switch to battery mode. A transfer time up to 10ms is present during switching

to battery mode.

XVI. Configuring EBM quantity

ENGLISH

Setting correct EBM (External Battery Module) quantity is critical for reaching the desired

backup time. Only if this value is set correctly, UPS will be able to maximize the battery

usage. The value represents amount of original battery packs fitted with 2 strings of 9Ah

batteries.

XVII. Configuring Load Segment

Load segments are groups of outlets that can be configured through the display. VFI RT

HID models have two configurable load segments. When UPS is turned on (it has

activated output), you can turn off a load segment. If the UPS is turned off (no output),

then a load segment cannot be turned on.

XVIII. Bypass Mode

If the bypass is set to enabled (value = 001), then the UPS would provide output to the

load as long as there is input. Turning off the UPS would essentially switch off the inverter

and supply unfiltered power to the load.

XIX. UPS Status Display String

LCD Display String

Description

STbY

UPS work at Standby mode (no output)

LINE

UPS work in Line mode

bYPA

UPS work in Bypass mode (no backup function!)

bATT

UPS work in Battery mode (no AC input)

TEST

UPS work in battery life/function test mode

ECO

UPS work in ECO mode

CVCF

UPS work in converter mode

SITE

Site fail, check input connection

FANF

Fan fail, check if fan is not blocked

bLOW

Battery low, recharge or replace batteries

bOPN

Battery open, check battery circuit connection

bATF

Battery fault, replace batteries

EPO

EPO, deactivate EPO

OVLD

Overload, disconnect load

AMbH

Ambient temperature too high

For following errors contact our technical support: CHGF / TEPH / SHOR / ISFT / bSFT / OVTP /

INVL / INVH / bUSH / bUSL / bUSE / bUSS / HIGH / NTCO

XX. Indicators and Audible alarm

Audible alarm

Backup Mode

Sounding every 4seconds

“bATT” on the screen

Low Battery

Sounding every second

“bLOW” on the screen

UPS Fault

Continuously Sounding

Red display

Overload

Sounding every second

“OVLD” on the screen

Battery Replacement

Sounding every second

Alarm can be muted when it is activated, but it will sound in case of low battery, fan

fault, overheat and other major fault.

XXI. Technical Specification

ENGLISH

Model

1000 RTS

1000 RT

1500 RT

2000 RT

3000 RT

Power

Watt

900W

1350W

1800W

2700W

Input

Input voltage range

161-276VAC

Frequency range

45-55 or 54-66 Hz for Normal Mode

Output

Voltage

220/230/240VAC

Voltage Regulation

±5% in battery mode

Frequency

50Hz or 60Hz ±0.2Hz

Waveform

Pure sinewave

Overload rating

12s @102%-130%; 1.5s @130%-150%; 100ms @ >150%

Internal

battery

Battery Type

external

3x12V/7A

4x12V/7A

4x12V/9

6x12V/9A

Recharge Time to

90% after

discharged

N/A

3 hours

Temperature

0 to 40°C

Humidity

0%-95% relative humidity (non-condensing)

Altitude

＜1000m

Storage Temperature

0-45 degC

Net weight

8.4kg

16.2kg

19.7kg

28.6kg

Dimensions

438 x 86.5 x 436

438X87x6

This manual suits for next models

Table of contents

Other PowerWalker UPS manuals

PowerWalker

PowerWalker VFI 10000CRM LCD User manual

PowerWalker

PowerWalker VFI 1000R/1U User manual

PowerWalker

PowerWalker VI 2000 LCD User manual

PowerWalker

PowerWalker VI 1000 User manual

PowerWalker

PowerWalker 1000 LCD/UK User manual

PowerWalker

PowerWalker VFI CG PF1 Series User manual

PowerWalker

PowerWalker VFI 20000-40000TAP 3/3 BI User manual

PowerWalker

PowerWalker VI CSW Series User manual

PowerWalker

PowerWalker VFI 10000P/RT LCD User manual

PowerWalker

PowerWalker PowerWalker VFI 10000RT LCD User manual

PowerWalker

PowerWalker VI 750 PSW User manual

PowerWalker

PowerWalker VFI 1000 RMG PF1 User manual

PowerWalker

PowerWalker VFI 3000 LCD Installation guide

PowerWalker

PowerWalker VFI 3/3 Series User manual

PowerWalker

PowerWalker VFI 160K CPG 3/3 BX User manual

PowerWalker

PowerWalker VFI 10000CP 3/3 User manual

PowerWalker

PowerWalker VI RT HID Series User manual

PowerWalker

PowerWalker VFI 6000RT LCD User manual

PowerWalker

PowerWalker PF 1 6K User manual

PowerWalker

PowerWalker 1000 LCD/UK User manual

PowerWalker

PowerWalker VI 400 User manual

PowerWalker

PowerWalker VFD 400 IEC User manual

PowerWalker

PowerWalker VFI 2000RT User manual

PowerWalker

PowerWalker VI RLP Series User manual

Popular UPS manuals by other brands

Pylontech

Pylontech Victron & Pylontech US5000 manual

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 user manual

Mecer

Mecer ME-1000-WTU user manual

Mustek

Mustek PowerMust 530(B) Plus Startup manual

Emerson

Emerson Liebert NXL series Operation and maintenance manual

MAKELSAN

MAKELSAN BOXER SERIES user manual

Block

Block PC-0524-400-0 manual

CyberPower

CyberPower CP585LCD user manual

Eaton

Eaton 3S Advanced user's guide

CyberPower

CyberPower Office Tower Series UPS 1000 user manual

CyberPower

CyberPower BM100 quick start guide

Best Power

Best Power 610 quick start guide

Best Power

Best Power Unity/I UT3K user manual

Mustek

Mustek PowerMust 400 Offline user manual

Xantrex

Xantrex Trace 512 UR-UPS owner's manual

Forza

Forza SL-1501UL user manual

LEGRAND

LEGRAND keor 310081 quick start guide

ABB

ABB Conceptpower DPA 500 operating manual