Power Fist Sump pump User manual

V1.0 8887184

Please read and understand all instructions before use. Retain this manual for

future reference.

8887184 1/3 HP Sump Pump V1.0

2 For technical questions call 1-800-665-8685

SPECIFICATIONS

Horsepower 1/3 HP

Voltage / Amperage 115 VAC / 4.6 A

Duty Cycle Continuous

Discharge Size 1 1/2 in.NPT with 1 1/4 in. adapter

Max. Discharge Head 27 ft

Flow Rate @ 5 ft 2,840 GPH

Flow Rate @ 10 ft 2,480 GPH

Flow Rate @ 15 ft 2,050 GPH

Flow Rate @ 20 ft 1,460 GPH

Material Housing Thermoplastic

Impeller Nylon

Volute Thermoplastic

Dimensions (L x W x H) 7.9 x 7.9 x 10.8 in.

Switch Type Tethered Switch

Cord Length 10 ft

Ambient Temperature 104°F (40°C)

Fluid Temperature 77°F (25°C)

HAZARD DEFINITIONS

Please familiarize yourself with the hazard notices found in this manual. A

notice is an alert that there is a possibility of property damage, injury or

death if certain instructions are not followed.

DANGER! This notice indicates an immediate and specific hazard that

will result in severe personal injury or death if the proper

precautions are not taken.

WARNING! This notice indicates a specific hazard or unsafe practice that

could result in severe personal injury or death if the proper

precautions are not taken.

CAUTION! This notice indicates a potentially hazardous situation that

may result in minor or moderate injury if proper practices are

not taken.

NOTICE! This notice indicates that a specific hazard or unsafe practice

will result in equipment or property damage, but not personal

injury.

V1.0 1/3 HP Sump Pump 8887184

Visit www.princessauto.com for more information 3

SAFETY

WARNING! Read and understand all instructions before using this tool. The

operator must follow basic precautions to reduce the risk of personal injury

and/or damage to the equipment.

Keep this manual for safety warnings, precautions, operating or inspection

and maintenance instructions.

WORK AREA

1. Operate in a safe work environment. Keep your work area clean, well-

lit and free of distractions. Place lights so you are not working in a

shadow.

2. Keep anyone not wearing the appropriate safety equipment away from

the work area.

3. Store unused tools properly in a safe and dry location to prevent rust

or damage. Lock tools away and keep out of the reach of children.

4. Do not install or use in the presence of flammable gases, dust or

liquids.

PERSONAL SAFETY

WARNING! Wear personal protective equipment approved by the Canadian

Standards Association (CSA) or American National Standards Institute (ANSI).

PERSONAL PROTECTIVE EQUIPMENT

1. Always wear impact safety goggles that provide front and side

protection for the eyes. Eye protection equipment should comply with

CSA Z94.3-07 or ANSI Z87.1 standards based on the type of work

performed.

2. Wear gloves that provide protection based on the work materials or to

reduce the effects of tool vibration.

3. Wear protective clothing designed for the work environment and tool.

4. Non-skid footwear is recommended to maintain footing and balance in

the work environment.

5. Wear a NIOSH approved respirator when working on materials that

produce hazardous fumes, dust or particulate matter.

PERSONAL PRECAUTIONS

Control the tool, personal movement and the work environment to avoid

personal injury or damage to tool.

8887184 1/3 HP Sump Pump V1.0

4 For technical questions call 1-800-665-8685

1. Do not operate any tool when tired or under the influence of drugs,

alcohol or medications.

2. Avoid wearing clothes or jewelry that can become entangled with the

moving parts of a tool. Keep long hair covered or bound.

3. Do not overreach when operating a tool. Proper footing and balance

enables better control in unexpected situations.

SPECIFIC SAFETY PRECAUTIONS

WARNING! DO NOT let comfort or familiarity with product (gained from

repeated use) replace strict adherence to the tool safety rules. If you use

this tool unsafely or incorrectly, you can suffer serious personal injury.

1. Use the correct tool for the job. This tool was designed for a specific

function. Do not modify or alter this tool or use it for an unintended

purpose.

2. Do not use the tool if any parts are damaged, broken, or misplaced.

Repair or replace the parts.

3. Do not run the pump if there is no water in the system.

4. Do not use pumps in water over 40°C (104°F). Avoid draining hot water

tanks into sump pits.

5. Do not power this device with anything other than a 120 volt power

source.

6. Do not use pumps for pumping mud, sand, cement, fats, salt, waste

water from toilets, oils, combustible or explosive substances or

chemicals.

7. The appliance is intended for pumping rainwater, fresh water, mains

water and chlorinated swimming pool water.

8. The pump must not be used for drinking water supply or for the

delivery of foodstuffs.

9. The device is not suitable for commercial or industrial use.

10. Risk of fire or explosion. Do not pump flammable or explosive fluids

such as gasoline, fuel oil, kerosene, etc.

11. Do not lift the pump by the power cord.

12. Be certain the pump power source is disconnected before installing or

servicing the pump.

13. Do not expose the pump to freezing temperatures. Freezing could

cause severe damage and will void the warranty.

V1.0 1/3 HP Sump Pump 8887184

Visit www.princessauto.com for more information 5

14. Do not insert fingers or any object into the pump or motor openings.

15. The pump normally runs hot. To avoid burns when servicing the pump,

allow it to cool for twenty minutes after shutdown before handling it.

16. Always check the pump before each operation. A damaged pump must

not be used. Have the pump serviced by a qualified service technician.

ELECTRICAL SAFETY

WARNING! Hazardous voltage can shock, burn or kill. When installing,

operating or servicing this pump, follow the safety instructions listed below.

1. Before installing this product, have the electrical circuit checked by an

electrician to ensure proper grounding.

2. Connect this product to a grounded circuit equipped with a Ground

Fault Circuit Interrupter (GFCI) device.

3. Do not install the pump in any location classified as hazardous by the

National Electrical Code, ANSI / NFPA 80-1984 or the Canadian Electrical

Code.

4. Do not allow the plug on the end of the electrical cord to be

submerged.

5. Do not use extension cords. They are a fire hazard and can reduce the

voltage sufficiently to prevent pumping and / or damage the motor.

6. Do not handle or service the pump while it is connected to the power

supply.

7. Ground the motor before connecting to an electrical supply.

8. Failure to ground the motor can cause severe or fatal electrical shock.

9. Do not ground to a gas supply line.

10. To avoid dangerous or fatal electrical shock, turn off the power to the

motor before working on electrical connections.

11. Check the voltage on the motor nameplate and make sure that the line

voltage of the electrical current supply is the same.

12. The supply voltage must be within 10% of the nameplate voltage.

Incorrect voltage can cause fire or seriously damage the motor and

voids the warranty. If in doubt, contact a licensed electrician.

13. Meet all national electrical code and local codes for all wiring.

14. Do not handle a pump or pump motor with wet hands, or when

standing on a wet or damp surface or in water.

8887184 1/3 HP Sump Pump V1.0

6 For technical questions call 1-800-665-8685

15. Always disconnect the power source before performing any work on or

near the motor or its connected load.

16. Protect yourself against electric shocks when working on electrical

equipment. Avoid body contact with grounded surfaces. There is an

increased chance of electrical shock if your body is grounded.

17. The fuse must be a residual current circuit-breaker with a measured

residual current of no more than 30 mA.

18. If the device is not in use, make sure that the plug is removed from the

power source.

19. Make sure that the device is switched off before plugging in the mains

cable.

20. Make sure that the device is switched off before unplugging it.

21. Disconnect the power supply before moving or transporting the device.

22. Do not install and switch on the pump if there are people or animals in

the medium, or have contact with the medium being pumped (such as

swimming pools).

WARNING! A qualified electrician should perform all wiring.

POWER CORD

1. Do not operate this tool if the power cord is frayed or damaged as an

electric shock may occur, resulting in personal injury or property

damage.

a. Inspect the tool's power cord for cracks, fraying or other faults in

the insulation or plug before each use.

b. Discontinue use if a power cord feels more than comfortably

warm while operating the tool.

c. Have the power cord replaced by a qualified service technician.

2. Keep all connections dry and off the ground to reduce the risk of

electric shock. Do not touch plug with wet hands.

3. Prevent damage to the power cord by observing the following:

a. Never use the cord to carry the tool.

b. Do not pull on the cord to disconnect the plug from an outlet.

c. Keep the power cord clear of the tool and the tool's work path

while in operation. The cord should always stay behind the tool.

d. Keep cord away from heat, oil, sharp edges or moving parts.

V1.0 1/3 HP Sump Pump 8887184

Visit www.princessauto.com for more information 7

4. Do not allow people, mobile equipment or vehicles to pass over

unprotected power cords.

a. Position power cords away from traffic areas.

b. Place cords in reinforced conduits.

c. Place planks on either side of the power cord to create a

protective trench.

UNPACKING

WARNING! Do not operate the tool if any part is missing. Replace the

missing part before operating. Failure to do so could result in a malfunction

and personal injury.

Remove the parts and accessories from the packaging and inspect for damage.

IDENTIFICATION KEY

A Carrying Handle

B Float Switch

C Pump Casing

D Discharge Outlet

ASSEMBLY & INSTALLATION

When this manual refers to a part number, it refers to the included Parts

Identification section.

HOSE CONNECTION

IMPORTANT! All threaded connections must be sealed with thread sealing

tape.

1. Connect the pressure pipe onto the pressure connection. For occasional

use, use a suitable water hose.

2. The use of rigid pipes with a non-return valve is recommended for use

at a fixed location. This prevents the return flow of liquid when

switching the pump off.

IMPORTANT! When using a hose, screw a suitable hose adapter onto the

pressure connection. Push the hose firmly onto the hose adapter and secure

with a hose clamp.

8887184 1/3 HP Sump Pump V1.0

8 For technical questions call 1-800-665-8685

LOCATION

1. The minimum diameter of the sump pit is 14 in. The minimum depth of

the pit is 16 in. The float switch must be able to move freely so that it

functions properly.

2. Make sure to locate the pump in a stable position (especially for

automatic operation).

3. Make sure that the pump is located in a way that ensures the inlet

openings at the suction base are unobstructed. Place the pump on a brick

or cement, do not place the pump directly on open earth or gravel.

4. Do not use the power cable or float switch to carry or hang the pump.

INSTALLATION

Tools Required for Assembly: Wrench, Phillips screwdriver.

1. The discharge port for this pump is 1-1/2 in. If a 1-1/4 in. discharge pipe

is already in place, wrap the threads of the included 1-1/4 in. adaptor

with sealant tape and thread into pump discharge port (Fig. 2-1).

2. Install a sump pump check valve (not included) into the pump (Fig. 3-1).

3. Connect a flexible connector (not included) to the check valve (Fig. 4-1).

Place the pump in the sump pit. Make sure the float switch operation is

not impaired by the connector.

4. Remove all small stones, gravel, mud, or other debris from the sump pit

before installing the pump.

5. A rigid discharge pipe is recommended to prevent the pump from

moving. If a flexible discharge hose is used, the pump must be secured

to prevent movement. The float switch could be trapped between a

moving pump and the sump wall, preventing the pump from turning on

or off.

6. Plug the pump into a GFCI outlet. The pump is now ready for use.

Fig. 2

Fig. 3

Fig. 4

V1.0 1/3 HP Sump Pump 8887184

Visit www.princessauto.com for more information 9

7. Check the pump by filling the sump pit with water

and observe the pump's operation through one

complete cycle and make sure the pump cannot

move in the sump pit and that the float switch

moves freely up and down (Fig. 5-1).

NOTICE! Do not adjust the tether length. The factory

has set the tether length to 4 inches. Altering the

length can result in pump failure.

OPERATION

1. Submerge the pump at an angle into the liquid to be pumped so that

no air pocket forms on the underside of the appliance. Suction would

be prevented by this air pocket. Once the pump is submerged, it can be

righted again.

2. Leave the pump on the bottom of the liquid source.

3. After the pump has been connected to the main power supply, the

pump will begin operating.

CAUTION! The float switch must be able to move so that the submersible

pump cannot run dry.

OPERATING TIPS

1. Dry-running operation causes increased wear and is to be avoided.

Therefore, the pump must be immediately switched off when water

fails to flow.

2. After having pumped chlorinated swimming pool water or other liquids

leaving residues, the pump should be rinsed with clean, clear water.

3. Sand and other abrasive materials in the liquid cause increased wear

and reduce the pump’s output.

4. If the pump becomes air locked, shut the power off for approximately 1

minute then restart the pump. Repeat several times to clear the air

from the pump.

CARE & MAINTENANCE

WARNING! Disconnect the mains plug before carrying out any work on the

device.

WARNING! All gaskets must be replaced after each disassembly of

components.

Fig. 5

8887184 1/3 HP Sump Pump V1.0

10 For technical questions call 1-800-665-8685

1. Maintain the tool with care. A tool in good condition is efficient, easier

to control and will have fewer problems.

2. Make certain that the power source conforms to the requirements of

your equipment.

3. When wiring an electrically driven device, follow all electrical and

safety codes, as well as the most recent Canadian Electrical Code (CE)

and the Canadian Centre for Occupational Health and Safety (CCOHS).

4. Always disconnect the pump from the power source prior to repairs.

Always reconnect the pump to the power source after the repairs.

5. Inspect the tool fittings, alignment, hoses and power supply cord

periodically. Have damaged or worn components repaired or replaced

by an authorized technician. Only use identical replacement parts

when servicing.

6. Only use accessories intended for use with this tool.

7. Maintain the tool’s labels and name plates. These carry important

information. If unreadable or missing, contact Princess Auto Ltd. for

replacements.

WARNING! Only qualified service personnel should repair the tool. An

improperly repaired tool may present a hazard to the user and/or others.

CLEANING

Rinse with clean water. Remove stubborn contamination with a brush and

detergent. Submerge the pump in a container with clean water and switch

on for a short time to rinse the inside of the pump.

CLEANING THE SUCTION AREA

Clean all accessible insides of the casing. Remove fibres which have wound

around the rotor shaft by opening the pressure connection. Remove

stubborn contamination with a brush and detergent.

IMPORTANT! Before using the pump again, first soak the pump so that any

possible dirt residues do not block the appliance.

MAINTENANCE SCHEDULE

BEFORE EACH USE

1. Perform a visual inspection of the pump casing and cables for damage.

2. Check the float switch for damage by lifting and shaking the switch to

check the free movement of the contained metal balls.

Table of contents

Languages:

Other Power Fist Water Pump manuals

Power Fist

Power Fist 8533614 User manual

Power Fist

Power Fist 8167561 User manual

Power Fist

Power Fist 8643108 User manual

Power Fist

Power Fist 8515736 User manual

Power Fist

Power Fist 8458440 User manual

Power Fist

Power Fist 8714784 User manual

Power Fist

Power Fist 8781460 User manual

Power Fist

Power Fist 8781593 User manual

Power Fist

Power Fist 8645830 User manual

Power Fist

Power Fist 8940041 User manual

Power Fist

Power Fist 8408890 User manual

Power Fist

Power Fist 5770096 User manual

Power Fist

Power Fist 8661621 User manual

Power Fist

Power Fist 8781510 User manual

Power Fist

Power Fist 8238347 User manual

Power Fist

Power Fist 8887150 User manual

Power Fist

Power Fist 8003174 Instruction Manual

Power Fist

Power Fist 8555724 User manual

Power Fist

Power Fist 8552937 User manual

Power Fist

Power Fist 180264 User manual

Power Fist

Power Fist 8167595 User manual

Power Fist

Power Fist 8265399 Instruction Manual

Power Fist

Power Fist 8643082 User manual

Power Fist

Power Fist 8605412 User manual

Popular Water Pump manuals by other brands

Neptun

Neptun NPHW 5500 operating instructions

Sensidyne

Sensidyne Gilian BDX-II Operation & service manual

Draper

Draper 47808 instructions

Trolla

Trolla 12820 manual

Sunfab

Sunfab SVH Series installation guide

WilTec

WilTec 50740 Operation manual

Fieldmann

Fieldmann FVC 5015 EK user manual

Everbilt

Everbilt EFSUB5-122HD Use and care guide

Graco

Graco Husky 3300e manual

esotec

esotec 101018 operating manual

moyno

moyno 2000 CC Service manual

Becker

Becker BASIC VASF 2.80/1-0.AC230 operating instructions

Sykes AmeriPumps

Sykes AmeriPumps GP100M Operation and maintenance instructions

DUROMAX

DUROMAX XP WX Series user manual

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 operating instructions

Franklin Electric

Franklin Electric IPS Installation & operation manual

Xylem

Xylem e-1532 Series instruction manual

Milton Roy

Milton Roy PRIMEROYAL instruction manual

Power Fist sump pump User manual

Popular Water Pump manuals by other brands