Polytron Headend Series User manual
1
PXU 848 C/T
Compact Headend with multiplexing
User manual
MADE IN GERMANY
0902008
2
Contents
1. Mounting and safety instructions 3
2. General information 5
3. Description 5
4. Scope of delivery 5
5. Input circuit 6
6. Mounting 6
6.1 Grounding 7
7. Installation 7
7.1 Pre-programming 8
7.2 Input level 8
7.3 Output level 8
8. General programming 9
8.1 Software installation at PC/Laptop 9
8.1.1 Installation of the driver 9
8.1.2 Installation of the programming software 10
8.2 Programming of the device parameters 11
8.2.1 Input parameters SAT reception 12
8.2.2 Input parameters for terrestrial range 14
8.2.3 Output parameters DVB-C 15
8.2.4 Output parameters DVB-T 16
8.3 Function “Multiplexing“ 18
8.3.1 Multiplexing of services (programs) 18
8.3.2 Selection of the channels to be encoded 20
8.3.3 LCN function 21
8.3.4 SID remapping - manual assignment of service IDs 22
8.4 Creation of NIT (Network Information Table) 24
8.4.1 NIT-Mode _____________________________________________________________ 25
8.4.2 Device NIT ____________________________________________________________ 25
8.4.3 Combined NIT__________________________________________________________ 26
8.5 Storage of the programming 33
8.5.1 Storage of settings 33
8.5.2 Loading of settings 33
8.5.3 Restart of the device_____________________________________________________ 34
8.6 CI menu __________________________________________________________________ 34
8.7 LAN function ______________________________________________________________ 35
8.7.1 Creating headends 36
8.8 Diagnostics 38
8.8.1 LED analysis 39
8.9 Firmware update 40
8.9.1 Overview firmware version 40
8.10 Changing the output window 42
8.11 Extras/additional adjustments _______________________________________________ 42
8.11.1 Function “Password“43
8.11.2 Teletext ON / OFF 44
8.11.3 EIT PID remapping _____________________________________________________ 45
8.11.4 Monitoring CI__________________________________________________________ 45
9. Application example_____________________________________________________________ 46
10. Technical data 47
3
1. Mounting and safety instructions
4
ATTENTION
This module contains ESD components! (ESD = Electrostatic Sensitive Device).
An electrostatic discharge is an electrical current pulse, which can flow also through an electrically
insulated material, when triggered by large voltage difference.
To ensure the reliability of ESD components, it is necessary to consider their most important handling rules:
Electrostatic sensitive components can be processed only on electrostatic protected area (EPA)!
Pay attention permanently to potential equalization (equipotential bonding)!
Use wrist straps, approved footwear for personnel grounding!
Avoid electrostatically chargeable materials such as normal PE, PVC, polystyrene!
Avoid electrostatic fields >100 V/cm!
Use only labeled and defined packing and transportation materials!
Damage caused by faulty connections and / or improper handling are excluded from any
liability.
Waste disposal
Electronic equipment does not belong in household waste, but must be disposed of properly in accordance
with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste
electrical and electronic equipment (WEEE).
Please return this device to the designated public collection points at the end of its use for disposal.
WEEE-Reg.-Nr. DE 51035844
GENERAL INFORMATION ON THE OPERATING INSTRUCTIONS
All parameter data are examples only.
User adjustable parameters are freely selectable.
Menu views can vary slightly depending on the software version; the operability does not change as a result.
The images in this manual are for illustrative purposes only.
5
2. General information
The new models PXU 848 C and PXU 848 T of the compact headend series enable the combined processing of
encrypted and open channels. This allows an easy and cost-effective extension with centrally decoded services for
the community antenna system. Also possible is the use as a free-to-air basic supply in a small boarding house or
hotel, because 40 programmes of 8 transponders are available. The compact headends PXU 848 C/T are used
wherever PAY-TV content and free-to-air channels are to be combined.
3. Description
The compact headends PXU 848 C/T convert the content of eight SAT transponders, terrestrial or cable channels to
either DVB-C or DVB-T. The reception mode can be selected individually at each of the eight inputs: DVB-S/S2,
DVB-T/T2 or DVB-C. Four of the eight channel strips are each provided with a CI interface for decoding encrypted
signals. The integrated multiplex function allows the generation of new output channels with contents of the different
input transponders. For this, the contents of various transponders can be decrypted via one smartcard and thus the
capacities of the smartcards can be optimally utilized. Via the USB interface, the headend can be programmed easily
and quickly. No knowledge regarding the allocation and management of IP addresses is required for this. The
selected settings can be printed, saved and also transferred to other devices via a USB stick. Due to the integrated
LAN connection, remote control of all parameters is possible. The supply voltages can be activated separately for the
SAT and terrestrial inputs with jumpers.
PXU 848 C = DVB-C output
PXU 848 T = DVB-T output
4. Scope of delivery
1 x PXU 848 X
1 x Power cable
1 x USB cable
1 x USB stick (programming software)
1 x LAN patch cable
1 x User manual
1 x Installation accessories
6
5. Input circuit
In the PXU 848 C/T, signals are directly fed to the input tuners. Due to the triple tuners, there are eight inputs each
for SAT and eight for terrestrial signals (DVB-T/T2 or DVB-C). In the ‘factory settings’ condition, there is a 12 VDC
voltage for LNB supply on SAT input tuners 1, 2, 5 and 6. This can be switched by corresponding jumpers J1, J2, J4
and J5. On tuners 4 and 8, a 12 V supply voltage for the terrestrial range can be activated by inserting the
corresponding jumpers J3 and J6. The operating states are indicated by external LEDs.
6. Mounting
The compact headend must be mounted in a well-ventilated room. The environmental temperature may not exceed
45 °C. It must be ensured that the air can circulate freely through the ventilation holes, especially in horizontal 19”
mounting. There must be at least 15 cm space around the device ventilation holes, so that the air can circulate
properly. For mounting or when working on the wiring, the power plug must be disconnected.
15 cm
15 cm
= Heat accumulation!!!
J3 > 12V on/off tuner 4 terr.
J5 > 12V on/off SAT tuner 6
J2 > 12V on/off SAT tuner 2
J1 > 12V on/off SAT tuner 1
J4 > 12V on/off SAT tuner 5
J6 > 12V on/off tuner 8 terr.
7
6.1 Grounding
The device must be grounded according to EN 60728-11.
- Strip approximately 15 mm of the cable insulation of the grounding cable (4mm2).
- Slide the stripped end under the earth screw and tighten the screw.
7. Installation
Connection of the input signals
Connect the SAT signals directly or via splitter(s) to the SAT tuner inputs. At SAT input tuners 1, 2, 5 and 6, a 12 V
DC voltage is applied for LNB supply.
DVB-T and DVB-C are connected via the terrestrial input. A 12 V supply is optionally available at the terrestrial input
tuners 4 and 8.
Please note the current consumption of each input may not exceed 250 mA. A total of
500 mA is available.
Input 4
SAT
Input 3
SAT
Input 7
SAT
Input 8
SAT
Input 2
SAT
LNB DC
Input 1
SAT
LNB DC
Input 6
SAT
LNB DC
Input 5
SAT
LNB DC
Input 1
Terr.
Input 2
Terr.
Input 3
Terr.
Input 4
Terr.
DC
Input 5
Terr.
Input 6
Terr.
Input 7
Terr.
Input 8
Terr.
DC
8
Insertion of the CI modules
To insert the CI modules, the covers must be removed. The picture shows the assignment of the CI slots to the
inputs. For wall mounting as shown in the picture, the double ridge guide of the CAMs must always be on the left
side. On the right side, the CAM has only a single guide ridge.
7.1 Pre-programming
The inputs and outputs of the device are pre-programmed ex-works with a standard frequency assignment. A
separate supplementary sheet with the pre-programming is included with the device. In this condition, all input
channels are present at the output. As described above, for reception of the pre-programmed ASTRA transponders,
the SAT inputs must be connected to the LNB in accordance with information on the polarization levels from the
supplement.
7.2 Input level
To ensure perfect reception, make sure that the level at the inputs is between 50 and 80 dBµV.
When receiving digital signals, it is advantageous to have a lower input level rather
than an excessively high one.
If the input level is too high, an attenuator must be used.
7.3 Output level
The output level at delivery is 90 dBµV. This can be changed via device programming. At the TEST socket, an
output level reduced by 20 dB is available.
CI slot 4
CI slot 2
CI slot 3
CI slot 1
Test -20 dB
Output
112-862 MHz
Network
management
port
USB port
Status LED
9
8. General programming
After connection, the device runs through an internal routine and all 8 channels are set up according to the previously
stored data. During this time, the Status LED next to the USB port flashes green. A connection between the PXU
848 X and the PC/laptop is only possible after the Status LED lights up permanently green or orange.
8.1 Software installation at PC
Download the software package from the homepage www.polytron.de (SATC12_Vxxx.zip) and unzip in the
directory of your choice (e.g. C:\ PXU 848).
The software can also be loaded from the enclosed USB stick.
8.1.1 Installation of the driver
Start the file Install_driver.cmd.
Follow the instructions on the screen.
Sometimes during first installation, the following dialogue can appear. This depends on the operating system. Carry
out the following instructions and select the fields as shown:
Then click the button Weiter to start the installation of the software.
No, not this time
Install software automatically
10
Then click the button Fertig stellen to finish the installation of the software.
The installation of the driver software is now finished.
8.1.2 Installation of the programming software
Install the software by starting the „Setup.exe“ program in the desired folder.
Follow the instructions on the screen.
Close the screen displays once the installation has ended.
After the installation of the programming software on the PC, the
PXU 848 X can be connected to the PC with the USB cable.
If this notice is displayed:
Continue the installation
The software was
installed for the following
hardware
USB
This manual suits for next models
2
Table of contents
Popular Multiplexer manuals by other brands
ADTRAN
ADTRAN Frameport 768 Specifications
Elo TouchSystems
Elo TouchSystems E247 Operation manual
Paradyne
Paradyne Hotwire 8786 installation instructions
RFL Electronics
RFL Electronics 9508D UCC instruction manual
Miranda
Miranda AMX-101i Guide to installation and operation
ShipModul
ShipModul MiniPlex-AIX NMEA-0183 manual
