Polarlite 1493203 User manual

Outdoor

Operating instructions

Decoration

LED projector “Snowﬂakes”

Item no. 1493203

Intended use

Use this product to decorate interior and exterior spaces (IP44).

For safety and approval purposes, you must not rebuild and/or

modify this product. If you use the product for purposes other

than those described above, the product may be damaged. In

addition, improper use can cause hazards such as short-circuiting,

ﬁre, electric shock etc. Read the instructions carefully and keep

them. Make this product available to third parties only together

with its operating instructions.

This product complies with the statutory national and European

requirements. All company names and product names are

Delivery content

• LED projector • L-shaped spanner

• Transformer • Operating instructions

• Ground spike

Safety instructions

Read the operating instructions carefully and especially

observe the safety information. If you do not follow the

safety instructions and information on proper handling

in this manual, we assume no liability for any resulting

personal injury or damage to property. Such cases will

invalidate the warranty/guarantee.

a) Persons / Product

• The device is not a toy. Keep it out of the reach of children and

pets.

• Do not leave packaging material lying around carelessly. These

may become dangerous playing material for children.

• Always check the product for damages before use. Should you

discover any damage, cease use of the product. If you discover

damages while the product is in use (i.e. damaged transformer),

do not touch the product, risk of fatal injury due to electric

shock! First disconnect the mains outlet to which the product

is connected from the power supply (ﬂip o the fuse and/or

automatic circuit breaker and then turn o the residual current

operated circuit breaker to disconnect the power outlet at all

phases). Now unplug the transformer from the power outlet.

Discontinue use of the product immediately, dispose of it in an

environmentally friendly fashion.

• Protect the product from extreme temperatures, strong jolts,

ﬂammable gases, vapours and solvents.

• Do not place the product under any mechanical stress.

• If it is no longer possible to operate the product safely, take it

out of operation and protect it from any accidental use. Safe

operation can no longer be guaranteed if the product:

– is visibly damaged,

– is no longer working properly,

– has been stored for extended periods in poor ambient

conditions or

– has been subjected to any serious transport-related stresses.

• Please handle the product carefully. Jolts, impacts or a fall even

from a low height can damage the product.

• The LEDs get hot during use. Keep the product away from

easily ﬂammable materials when in use.

• The product generates heat during use. Do not cover the

product during use.

• The product is suitable for both indoor and outdoor use.

• Attention, LED light: Do not look directly into the LED light! Do

not look into the beam directly or with optical instruments!

• The mains outlet must be located near to the device and be

easily accessible.

• Only the included transformer may be used as a power supply.

• The transformer may be supplied with power only via a properly

installed power outlet connected to the public supply mains.

Before plugging in the transformer, verify that the transformer's

nominal voltage complies with the voltage of your power supply

company.

• Never plug in or unplug the transformer with wet hands.

• Do not unplug the transformer by tugging on the cord, grasp

and pull the power plug using the provided gripping surface.

• When setting up the product, make sure that the cables are not

pinched, kinked or damaged by sharp edges.

• Always lay the cables so that nobody can trip over or become

entangled in them. This poses a risk of injury.

• Unplug the transformer in case of a thunder storm for safety

reasons.

• Do not over-tighten the screws. Over-tightening the screws may

cause damage to the threading and can impair the strength of

screw connections.

b) Miscellaneous

• Consult an expert when in doubt about operation, safety or

connection of the device.

• Maintenance, modiﬁcations and repairs are to be performed

exclusively by an expert or at a qualiﬁed shop.

• If you have questions which remain unanswered by these

operating instructions, contact our technical support service or

other technical personnel.

Product overview

310 mm

98 mm

5 m

Operation

Do not install or operate the product under water.

Make sure the cable hangs loosely and is not overly

tensioned. Failure to heed this warning may cause the

cables to tear.

Do not connect the product to the power supply while it

is still in the packaging. Uncoil the power cable fully.

Do not hang any objects from the product and do not

cover the product.

When inserting the ground spike into the soil, do not

use any tools (e.g. hammers), as such would damage the

product.

Check all screw connections from time to time. Screw

connections may loosen over time due to adjusting and

moving the product.

The LEDs are neither dimmable nor replaceable.

1. Uncoil the power cable fully.

2. Loosen the screw by turning it anticlockwise, and remove the

spring washer and ﬂat washer from the ground spike using

the spanner provided (see ).

3. Attach the lamp to the ground spike using the screw, spring

washer and ﬂat washer (see ).

4. Connect the plug of the power cable to the socket on the

transformer. It is only possible to connect in one way. Secure

the connection by turning the plug’s screw cap onto the

transformer’s thread (see ).

5. Choose a suitable location to set up the device with soft

ground. Stony ground will damage the ground spike.

Carefully insert the LED projector including the ground spike

all the way into the soil (see ).

6. Loosen the lateral hexagon screws using the hexagon key

provided. Adjust the angle of the projector as desired and

then retighten the screws.

7. Connect the transformer to a power outlet. The projector is

switched on and starts rotating.

The product has no power switch and is always on as long as

it is connected to the power supply. Disconnect the power

supply in order to switch the LED projector o.

Cleaning and care

• Disconnect the transformer from the mains socket and let the

LED projector cool down suciently before cleaning.

• Do not use any abrasive or chemical cleaners. To clean, use a

clean, dry, lint-free cloth. For stubborn dirt, slightly dampen the

cloth with water.

• Allow the product to dry completely before continued use.

Disposal

Electronic devices are recyclable waste and must not

be disposed of in the household waste. At the end of its

service life, dispose of the product in accordance with

applicable regulatory guidelines.

You thus fulﬁll your statutory obligations and contribute

to the protection of the environment.

These operating instructions are published by CEI Conrad Electronic International (HK) Limited, 18th Floor, Tower 2,

Nina Tower, No. 8 Yeung Uk Road, Tsuen Wan, New Territories, Hong Kong. All rights including translation reserved.

Reproduction by any method, e.g. photocopy, microﬁlming, or the capture in electronic data processing systems

require the prior written approval by the editor. Reprinting, also in part, is prohibited. These operating instructions

represent the technical status at the time of printing.

1493203_v1_0916_02_m_ls_EN(2)distributed by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau

Technical data

a) LED projector

Protection type ......................................IP44

Operating voltage.................................12 V/DC, 0.3 A

Power consumption.............................4.7 W

Number of lights....................................4 x 1 W LED

Light color ................................................Multicolor

Cable length.............................................5 m

Dimensions (Ø x W) ............................98 x 310 mm

Distance to illuminated area ............5 m

Illuminated area......................................5 x 5 m

Projector rotation..................................3 turns / minute

Operating conditions ..........................-20 to +40 °C / 0 – 100 % RH

Storage conditions ...............................-20 to +40 °C / 0 – 100 % RH

Weight ........................................................760 g

b) Transformer RSS1002-036120-W2E-F

Protection type ......................................IP44

Input voltage ...........................................100 – 240 V/AC, 50/60Hz

Output voltage.......................................12 V/DC

Output current .......................................300 mA

Output power .........................................max. 3.6 W

Table of contents

Other Polarlite Outdoor Light manuals

Polarlite

Polarlite Iron-Ice User manual

Polarlite

Polarlite Spot 8 User manual

Polarlite

Polarlite 1497354 User manual

Polarlite

Polarlite 1558362 User manual

Polarlite

Polarlite Basis70 User manual

Polarlite

Polarlite 1518441 User manual

Polarlite

Polarlite 1642711 User manual

Polarlite

Polarlite PWL 10 User manual

Popular Outdoor Light manuals by other brands

Sealey

Sealey LED37 instructions

nordlux

nordlux VEJERS Mounting instruction

SImx

SImx ELITE LED LHTC637 installation instructions

GEV

GEV CAROLINE 10833 manual

NEBO

NEBO NEB-LSP-0020 Use and care guide

WE-EF

WE-EF PFL540 LED Installation and maintenance instructions

Lindby

Lindby 9949029 Intended use

HEPER

HEPER DOGO Side LW6048.585-US Installation & maintenance instructions

HEPER

HEPER LW8034.003-US Installation & maintenance instructions

Maretti

Maretti VIBE S 14.6080.04.A quick start guide

BEGA

BEGA 84 253 Installation and technical information

HEPER

HEPER MINIMO Installation & maintenance instructions

LIGMAN

LIGMAN BAMBOO 3 installation manual

Maretti

Maretti TUBE CUBE WALL 14.4998.04 quick start guide

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB installation instructions

urban ambiance

urban ambiance UQL1273 installation instructions

TotalPond

TotalPond 52238 instruction manual

Donner & Blitzen

Donner & Blitzen 0-02661479-2 owner's manual