Planet IGS-5225-4T2S User manual

Industrial L2+ Multi-Port Full Gigabit

Managed Ethernet Switch

IGS-5225-4T2S/IGS-5225-4P2S/IGS-5225-4UP1T2S

IGS-5225-8P4S/IGS-5225-8P4S-12V/IGS-5225-8P2T2S

IGS-5225-8P2T4S

Quick Installation Guide

Table of Contents

1. Package Contents................................................................................. 3

2. Requirements....................................................................................... 5

3. Wiring the Power Inputs ....................................................................... 6

3.1 Grounding the Device..................................................................... 8

4. Terminal Setup..................................................................................... 9

4.1. Logging on to the Console............................................................ 10

 4.2 ConguringIPAddress ................................................................. 11

5. Starting Web Management .................................................................. 13

5.1 Logging in to the Industrial Managed Switch .................................. 13

 5.2 SavingCongurationviaWeb ....................................................... 15

6. RecoveringBacktoDefaultConguration ............................................. 16

7. Customer Support .............................................................................. 19

1. Package Contents

Thank you for purchasing PLANET L2+ Industrial Managed Switch, IGS-5225

Series. The number of the ports of these models is as follows:

GbECopper

Ports

PoEPorts GbESFPPorts

at/af bt* 1G 2.5G*

IGS-5225-4T2S 4- - - 2

IGS-5225-4P2S 4 4 -2-

IGS-5225-4UP1T2S 5-4-2

IGS-5225-8P4S 8 8 -2 2

IGS-5225-8P4S-12V 8 8 -2 2

IGS-5225-8P2T2S 10 8- - 2

IGS-5225-8P2T4S 10 8-2 2

*bt:Compatiblewith802.3at/afPoE

*2.5G:Compatiblewith1000BASE-SX/LX/BXSFPtransceiver

“Industrial Managed Switch” mentioned in this Quick Installation Guide

refers to the above models.

Open the box of the Industrial Managed Switch and carefully unpack it.

The box should contain the following items for each model of the Industrial

Managed Switches:

The

Industrial

Managed

Switch

Quick

Installation

Guide

Sheet

Wall

Mounting

Kit

DB9 to

RJ45,

RS232

Console

Cable

RJ45

Dust

Cap

SFP

Dust

Cap

IGS-5225-

4T2S     5 2

IGS-5225-

4P2S     5 2

IGS-5225-

4UP1T2S     6 2

IGS-5225-

8P4S     9 4

IGS-5225-

8P4S-12V     9 4

IGS-5225-

8P2T2S     11 2

IGS-5225-

8P2T4S     11 4

If any of these are missing or damaged, please contact your dealer

immediately. If possible, retain the carton including the original packing

materials to enable you to repack the product in case there is a need to return

it to us for repair.

2. Requirements

The Industrial Managed Switch provides remote login interface for

management purposes. The following equipment is necessary for further

management:

zWorkstations running Windows 10/11, MAC OS 10.15 or later, Linux, UNIX,

or other platforms are compatible with TCP/IP protocols.

zWorkstationsareinstalled withEthernetNIC(NetworkInterfaceCard)

zSerialPortConnection(Terminal)

 The above Workstations come with COM Port (DB9) or USB-to-RS232

converter.

 The above Workstations have been installed with terminal emulator, such

as putty or tera term.

 Serial cable -- one end is attached to the RS232 serial port, while the

other end to the console port of the Industrial Managed Switch.

zEthernetPortConnection

 Network cables -- Use standard network (UTP) cables with RJ45 connec-

tors.

The above PC is installed with Web browser.

It is recommended to use Chrome 98.0.xxx or above to access

the Industrial Managed Switch.

3. Wiring the Power Inputs

The Upper Panel of the Industrial Managed Switch comes with one

6-contact terminal block. Please follow the steps below to insert the power

wire.

1.Insert positive/negative DC power wires into Contacts 1 and 2 for Power 1,

or Contacts 5 and 6 for Power 2.

IGS-5225-8P4S/IGS-5225-8P2T2S/IGS-5225-8P2T4S:DC48~54V

PWR1 PWR2

Alarm

DI1 DO0 DO1DI0 GNDGND

DC Input:

48-54V , 6A max.

Max. Fault Alarm Loading: 24V, 1A

1 2 3 4 5 6

Figure 3-1: IGS-5225-8P4S/IGS-5225-8P2T2S/IGS-5225-8P2T4S Upper Panel

IGS-5225-4UP1T2S:DC48~54V

DI1 DO0 DO1DI0 GNDGND

DC Input:

48-54V , 8.3A max.

Dual power input is required

for maximum PoE loading.

Refer to user’s manual for

more details.

PWR1 Alarm PWR2

V1+ V2+

Max. Fault Alarm Loading: 24V, 1A

1 2 3 4 5 6

Earth Ground

Figure 3-2: IGS-5225-4UP1T2S Upper Panel

IGS-5225-4T2S:DC12~48V,AC24V

Max. Fault Alarm Loading: 24V, 1A

DC Input: 12-48V

, 1.7A max.

AC Input: 24V

, 1A max.

V1+ V2+

PWR1 PWR2Alarm

1 2 3 4 5 6

Figure 3-3: IGS-5225-4T2S Upper Panel

IGS-5225-4P2S:DC48~56V

FaultPWR1

V1+ V2+

PWR2

Max. fault loading: 24V, 1A

DC Input: 48-56V

3.5A max.

1 2 3 4 5 6

Figure 3-4: IGS-5225-4P2S Upper Panel

IGS-5225-8P4S-12V:DC12~54V

PWR1 PWR2

Alarm

DI1 DO0 DO1DI0 GNDGND

DC Input:

12-54V , 6A max.

Max. Fault Alarm Loading: 24V, 1A

1 2 3 4 5 6

Figure 3-5: IGS-5225-8P4S-12V Upper Panel

2.Tightenthewire-clampscrewsforpreventingthewiresfromloosening.

123456

V+ V- V+ V-

Power 1 Power 2

Positive(+)Pin Negative(-)Pin

IGS-5225Series Pin 1/5 Pin 2/6

1. The wire gauge for the terminal block should be in the range

from 12 to 24 AWG.

2.Please check the wire AWG Ampere specification before

connectingPLANETIndustrialManagedSwitch.

PWR1 and PWR2 must provide the same DC voltage for pow-

er load balance while operating with dual power input.

3.1 Grounding the Device

Users MUST complete grounding wired with the device; otherwise, a sudden

lightning could cause fatal damage to the device.

PWR1 PWR2

Alarm

DI1 DO0 DO1DI0 GNDGND

DC Input:

48-54V , 6A max.

Max. Fault Alarm Loading: 24V, 1A

1 2 3 4 5 6

EMD(Lightning)damageisnotcoveredunderwarranty.

4. Terminal Setup

To congure the system, connect a serial cable to a COM port on a PC or

notebook computer and to RJ45 type serial (console) port of the Industrial

Managed Switch. The console port of the Industrial Managed Switch is DCE

already, so that you can connect the console port directly through PC without

the need of null modem.

PC/Workstation with

Terminal Emulation Software

RJ45 to DB9 RS232 Cable

Serial Port

Console Port

115200,N,8,1

IGS Industrial Managed Switch

Console

115200,N,8,1

P1 P2 Fault

DIDO

Ring

R.O.

PoE Usage

ACT1000 LNK

ACT100 LNK

A terminal program is required to make the software connected to the

IGS-5225seriesIndustrialManagedSwitch.

1. Run terminal program on the OS.

2.When the followingscreenappears,makesurethatthe COM port should be

conguredas:

Baud: 115200

Parity:None

Data bits: 8

Stop bits: 1

Flowcontrol:None

4.1. Logging on to the Console

Once the terminal has been connected to the device, power on the Industrial

Managed Switch and the terminal will display “running testing procedures”.

The following console screen is based on the IGS-

5225-4UP1T2S. The display of the other IGS-5225 series is the

sameasthatoftheIGS-5225-4UP1T2S.

Then, the following message asks to log in user name and password. The

default user name and password are shown as follows and the login screen in

Figure4-1appears

Username:admin

Password: admin

Figure 4-1: Console Login Screen

The user can now enter commands to manage the Industrial Managed Switch.

For a detailed description of the commands, please refer to the following

chapters.

1.For security reason, please change and memorize the

new password after this first setup.

2. Only accept command in lowercase letter under console inter-

face.

Other manuals for IGS-5225-4T2S

This manual suits for next models

Table of contents

Other Planet Switch manuals

Planet

Planet WGSW-28040 Installation instructions

Planet

Planet GSD-1022UP User manual

Planet

Planet FSD-808P User manual

Planet

Planet GS-5220 Series User manual

Planet

Planet IGS-824UPT User manual

Planet

Planet FSD-1008HP User manual

Planet

Planet FSD-1603 User manual

Planet

Planet USB 2.0 External Hub UH-421 User manual

Planet

Planet IFGS-1022HPT User manual

Planet

Planet VC24024 Operator's manual

Planet

Planet IGS-4215-8UP4X User manual

Planet

Planet IGS-1020TF User manual

Planet

Planet SGSD-1022 User manual

Planet

Planet XGSW-28040 User manual

Planet

Planet ISW-800T-M12 User manual

Planet

Planet GSW-1602SF User manual

Planet

Planet VC-1602 User manual

Planet

Planet VC-820M User manual

Planet

Planet MGS-6320-8HP2X User manual

Planet

Planet IGS-4215-4P4T User manual

Planet

Planet FGSW-262 User manual

Planet

Planet NOVASwitch FNSW-8086F User manual

Planet

Planet EMQ-SGS-5240 Series User manual

Planet

Planet GSW-1402S User manual

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual