Planet ERT-805 User manual

Table of Contents

Chapter 1 Package Contents 1

Unpacking the router 1

Hardware install section 2

Connect a Serial Device 2

Chapter 2 Terminal Setup 3

Chapter 3 Logon to the Console 5

Chapter 4 Configure Password 7

Chapter 5 Configuration IP Address 9

1

This page is intentionally left blank

1

Chapter 1

Package Contents

Thank you for purchasing ERT-805 Serial WAN Router.

This installation guide provides the basic information of the router, ERT-805, including,

hardware installation, console interface login and LAN interface setup. For more

information of the router, please also refer to the user’s manual of the router in the CD-

ROM.

Unpacking the router

Open the box of the ERT-805 router and carefully unpack it. The box should contain the

following items:

• ERT-805 Serial WAN Router

• Power Cord

• DB9 to RJ-45 changer

• RJ-45 to RJ-45 modem cable

• User’s Manual CD

• Quick installation Guide

 Note:

if any item is found missing or damaged, please contact your local

reseller immediately.

2

3

Hardware install section

To install ERT-805 serial router, just following the step:

• Connect an Ethernet device

• Connect a Serial device

• Connect a terminal or PC

• Connect the power supply

Connect a Serial Device

WAN Option WAN Encapsulation

Frame relay

X.25

Link control (HDLC) or ppp

Frame-relay

X.25

2

3

Chapter 2

Terminal Setup

To congure the system, connect the provided RJ-45 cable and DB9 connector to a COM

port on a PC or notebook computer and to serial (console) port of the device.

When the connection between the PC and ERT-805 is ready, run the Hyper Terminal and

congure its communication parameters. It can be accessed from the Start menu. Click

START, then Programs, Accessories and then Hyper Terminal.

The operating mode of the console port is:

• Baud rate: 9600

• Data bits: 8

• Parity: none

• Stop bits: 1

• Flow control: None

After nished the setting, click OK.

Or run the Mrcom32.exe under DOS mode (The program can be found in the CD-ROM,

directory “/utility”). It can access from START menu click RUN then type “e:/utility/

mrcom32 com1 9600” where assume ‘e’ drive is the CD-ROM drive.

4

5

This page is intentionally left blank

4

5

Chapter 3

Logon to the Console

Once the terminal has connected to the device, power on the device, the terminal will

display that it is running POST (Power on self-test) procedures.

Then, screen as below will show up. The ERT-805 will prompt with “>”. This means ERT-

805 is in operating mode now.

Types “enable” to enter privilege mode. The ERT-805 will prompt with “#” for privilege

mode. By default there is no password.

 Note:

For security reason, please follow the following section to change

the new password after this rst setup. Memorize the password

or write it down and store in a secured place.

6

7

This page is intentionally left blank

6

7

Chapter 4

Configure Password

1. Once log on to the console, the following screen displayed.

Fig 1: The privilege Screen of ERT-805

2. Types “cong terminal” to enter conguration mode. ERT-805 will prompt

“<console>#”

Fig 2: Conguration mode Screen

3. Then type command enable password “abc” to setup the enable privilege password

where abc is the password. ( password can be any alphabetic or numerical with up

to 16 ASCII character is allowed)

Fig 3: conguration for password

4. Key in “end” to close the congure mode and key in “wr” to store the setting and

make the setting activated right away.

8

9

This page is intentionally left blank

Other manuals for ERT-805

1

Table of contents

Other Planet Network Router manuals

Popular Network Router manuals by other brands

Allnet

Allnet ALL0333AU user guide

HomeSeer

HomeSeer HT-SEL Getting started guide

Sercomm

Sercomm Genesis OC3505D Quick installation guide

Billion

Billion BIPAC 5102 Series user manual

TP-Link

TP-Link TD-8817 QIG

Motorola

Motorola MR1900 user guide

Digi

Digi IX14 user guide

Cisco

Cisco NCS 540 Hardware installation guide

XAVi

XAVi X8821e user manual

BEC

BEC 6200WZL Quick installation guide

MikroTik

MikroTik hAP ac3 Series quick start

Korenix

Korenix JetNet 5428G Series user manual

NETGEAR

NETGEAR FS526T - Switch installation guide

Korenix

Korenix JetNet 5710G Series user manual

Automated Logic

Automated Logic ZN551 Technical instructions

Cisco

Cisco ASR 1000 Series Installation and configuration guide

EnGenius

EnGenius ESR-9710 quick start guide

Cisco

Cisco 805 Series Product overview