Planet FT-802S User manual

10/100Base-TX to 100Base-FX

TP to Fiber

Ethernet Bridge Converter

Trademarks

Contents subject to revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp.

The information in this manual is subject to change without notice.

All other trademarks belong to their respective owners.

FCC Warning

This equipment has been tested and found to comply with the

regulations for a Class A digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed

and used in accordance with this user’s guide, may cause harmful

interference to radio communications. Operation of this equipment

in a residential area is likely to cause harmful interference, in

which case the user will be required to correct the interference at

his own expense.

CE Mark Warning

This is a Class A product. In a domestic environment, this product

may cause radio interference, in which case the user may be

required to take adequate measures.

Revision

User's manual for PLANET Fast Ethernet Converter

Multi-mode: FT-801, FT-802

Single-mode: FT-802S

Rev 1.0 (Oct. 2000)

Part No. EMFT801

1. Overview

Thank you for purchasing PLANET FT-80X family 10/100Mbps

Ethernet Twisted pair to 100Base-FX Fiber-optic Bridge

Converter. This converter is used to convert one type media signal

to other type equivalent that allows two type segments connect

easily, efficiently and inexpensively. This converter can be used as

a standalone unit or as a slide-in module to the 19” media chassis

(up to 10 units) for a TP and Fiber combined networks at a central

wiring closet. Please contact with your sales representative for

more about the 19” media chassis.

2. Model List

Your Fast Ethernet Converter comes with one of the following

models.

ðFT-801 : on board ST fiber connector

ðFT-802/S : on board SC fiber connector

Models with last character “S” indicate the fiber-port is with

“Single-Mode” optic fiber connector.

In the following sections, the term “FT-80X” indicates the product

family above.

3. Checklist

Your FT-80X carton should contain the following items:

ðThe Fast Ethernet Bridge Converter

ðAC-DC Power Adapter (Output: 5VDC, 2 A max.)

ðThis user’s guide

If any item is missing or damaged, please consult the dealer from

whom you purchased your Fast Ethernet Converter.

4. Product Outlook

Right View

One RJ-45

Twisted-Pair

jack, one

fiber-optic

connector and

six LED

indicators.

Left View

One DC jack for

DC power input.

One DIP switch

for Fiber-optic

mode selection,

FDX for

full-duplex, and HDX for falf-duplex.

Side View

DTE MPR

One DIP Switch for TP Device selection.

5. Installing the Converter

Please follow these steps to install the converter:

•Turn off the power of the device/station in a network to which

the FT-80X will be attached

•Ensure that there is no activity in the network

•Attach fiber cable from the FT-80X to the fiber network. TX,

RX must be paired at both ends

•Attach a Cat. 5 UTP cable from the 10/100Base-TX network

to the RJ-45 port on the FT-80X.

•Connect the 5VDC power adapter to the FT-80X and verify

that the Power LED lights up.

•Turn on the power of the device/station, the TX Link and FX

Link LEDs should light when all cables are attached

FT-80X

10/100Base-TX

Cat. 5/5e TP

Cable Network

100Base-FX

Fiber Network

10/100Base-TX to 100Bas-FX

Note:

nRJ-45/STP, UTP Cat 5, straight-through cable is accepted

nCabling from FT-80X TP port to a TP device is as below:

qTo Workstation: DIP switch on DTE

qTo Hub/Switch: DIP switch on MTR

nPlease refer to section 8 for more about the wiring distance of

your TP, Optic-fiber networks.

6. Duplex Mode setting

The TP port of FT-80X support duplex mode detection by

auto-negotiation (A-N). The following is the duplex mode

parameters:

Fast Ethernet Device FT-80X Duplex

Mode support

Ethernet / Fast Ethernet Hub Half-Duplex

Ethernet / Fast Ethernet Switch (without A-N)

Half-Duplex

Fast Ethernet Devices *

Support Auto-Negotiation Full-Duplex /

Half-Duplex

Note: Normally, an A-N switch will detect and set to

full-duplex, where a dual-speed hub will detects Half.

There is a DIP-switch as in the left view above. Please check

and follow the duplex mode of the fiber device and have the

duplex selection to your FT-80X.

7.LED indication

LED COLOR

DESCRIPTION

Blinks when any FX packets transmitting

FX Link

/ACT Green

Lit when Fiber connection is good

Blinks when any FX packets receiving

Blinks when any TP packets transmitting

TP Link/

ACT Green

Lit when TP connection is good

Blinks when any TP packets receiving

FDX/COL

*Green

Lit when Full-duplex mode is enabled in

FX port and blink shows collision detected.

100 Green

Lit when the port runs in 100Mbps.

Remains off while LINK LED lit represent

the port runs in 10Mbps

PWR Green

Lit when +5VDC power detected

Note: Fiber-optic Partner should be set to the correct mode

according to this FDX indicator for optimal network performance.

8. Cable Connection Parameter

The limitations are as below:

Duplex Connection Limitation (max.)

Twisted Pair

Half / Full

Node to Node

Node to Switch/Hub 100 meters

Multi-Mode Converters

MM Half Node to Node

Node to Switch 412 meters

MM Full Node to Node

Node to Switch 2 kilometers

Single-Mode Converters (FT-80XS)

SM Full Node to Node

Node to Switch 20 kilometers

9. FT-80X Technical Specifications

The FT-80X comes with the following standard features:

•Standard : IEEE802.3/u, 10/100Base-TX and 100Base-FX

•Connectors :

ðOne RJ-45 Twisted Pair, EIA568

ðOne Fiber-optic, 1300nm wavelength, connector-type vary

with model

•Data Transfer Rate :10/100Mbps ( TP), 100Mbps (FX)

•Duplex mode support :Full or half-duplex mode by Auto-

Negotiation (TP)

•LED indicators :PWR, TX Link/ACT, FX

Link/ACT, FDX, 100, FDX

•Power Requirement :5V DC, 2A

•Ambient Temperature:0°to 50°C (operating)

•Humidity :5% to 90% (non-condensing)

•Dimension : 26 x 70 x 97mm (HxWxD)

•Cable:

ðUTP : Cat 5 UTP cable

ðFiber : MM: 50/125 µm or 62.5/125 µm optic fiber

ðFiber : SM: 8.3/125, 8.7/125, 9/125 µm optic fiber

Connecting to Router, Bridge, or Switch, Hub, please refer to the

device’s Technical Manual.

10. Power information

The power jack of FT-80X is with 2.5mm in the central post and

required +5VDC power input. It will conform to the bundled

AC-DC adapter and Planet’s Media Chassis. Should you have the

problem to make the power connection, please contact your local

sales representative.

Please keep the AC-DC adapter as spare parts when your FT-80X

is installed to a Media Chassis.

Part No.:EM-FT801 ISO9002

This manual suits for next models

Table of contents

Other Planet Media Converter manuals

Popular Media Converter manuals by other brands

SoundTraxx

SoundTraxx Blunami BLU-2200 user guide

SPROLINK

SPROLINK VA1 user manual

Acclaim Lighting

Acclaim Lighting DDC-1-AC user guide

Nikon

Nikon AF-S TC-20E III user manual

Axis

Axis AXIS Q7406 user manual

Omega

Omega TAC80B-J instruction sheet

Zoom

Zoom Thunderbolt TAC-2R Operation manual

OST

OST iConverter 10/100M quick start guide

Vertiv

Vertiv Netsure user manual

birddog

birddog MINI user guide

Roland

Roland GI-10 owner's manual

Wallenstein

Wallenstein WX310 Operator's manual

Pace

Pace MSS 200-1 Service manual

Solar Converters

Solar Converters EQ 12/24-50 manual

CYP

CYP EL-7400V Operation manual

TIE

TIE MIDI 1i1o user manual

DCS

DCS Vivaldi Upsampler user manual

Westermo

Westermo MCW-211 SERIES user guide