PL&T PLT-11397 User manual

Installation Instruction

TYPEA(Slip-ﬁtter)

Step 1: Loosen the 4 screws on the lamp

holder,connect the wires correctly and

put the wires into the lamp pole, then lock

the screws well to ﬁx the lamp on the lamp

pole.

Step 2: Loosen the locking bolt with tools,

rotate the lamp and lock the screw after

determining required angle.

Notice: Locking bolt can be only compatible

with a lamp pole that the outer diameter is

¢60, lamp adjustable angle is 0-90°

Step 1.Use tools to take screw apart and

put installed iron bar away, remove ﬁxed

screw and open junction box, then pass

the AC wire through it.

Step 2.Use tools to ﬁx the lamp on square

lamp pole, connect the wires correctly

and make waterproof measures well,

close the junction box and ﬁnish installation.

Step 3.Notice: Remove the rubber mat

when the lamp is installed on round lamp

pole

Notice: Lamp adjustable angle is 0-30°

TYPEB(Square/Round pole mount with slip-ﬁtter function)

TYPEC(Square/Round pole mount)

Step 1.Use tools to take screw apart and

put installed iron bar away, remove ﬁxed

screw and open junction box, then pass

the AC wire through it.

Step 2.Use tools to ﬁx the lamp on square

lamp pole, connect the wires correctly and

make waterproof measures well, close the

junction box and ﬁnish installation.

Notice: Remove the rubber mat when the

lamp is installed on round lamp pole.

Installation Instruction

TYPED(Trunnion)

Step 1.Mark the position of the ﬁxing

holes with foold lightbracket, then drill

the ﬁxing holes.

Step 2.Input two expansion bolts.

Step 3: Waterproof measures must be taken

after connecting the wire correctly, install the

lamp well after putting the wires back into the

trunking.

Attention: Lamp adjustable angle is 0-90°

wall hammer

expansion bolt

electrical drill

TYPEE(Yoke)

Step 3:Waterproof measures must be taken after connecting the wire correctly, install

the lamp well after putting the wires back into the trunking.

Attention: Lamp adjustable angle is 0-90°

Installation Instruction

Step 1.Mark the position of the ﬁxing

holes with foold lightbracket, then drill

the ﬁxing holes.

Step 2.Input two expansion bolts.

wall hammer

expansion bolt

electrical drill

Other PL&T Outdoor Light manuals

PL&T

PL&T PLT-11562 User manual

Popular Outdoor Light manuals by other brands

Sealey

Sealey LED37 instructions

nordlux

nordlux VEJERS Mounting instruction

SImx

SImx ELITE LED LHTC637 installation instructions

GEV

GEV CAROLINE 10833 manual

NEBO

NEBO NEB-LSP-0020 Use and care guide

WE-EF

WE-EF PFL540 LED Installation and maintenance instructions

Lindby

Lindby 9949029 Intended use

HEPER

HEPER DOGO Side LW6048.585-US Installation & maintenance instructions

HEPER

HEPER LW8034.003-US Installation & maintenance instructions

Maretti

Maretti VIBE S 14.6080.04.A quick start guide

BEGA

BEGA 84 253 Installation and technical information

HEPER

HEPER MINIMO Installation & maintenance instructions

LIGMAN

LIGMAN BAMBOO 3 installation manual

Maretti

Maretti TUBE CUBE WALL 14.4998.04 quick start guide

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB installation instructions

urban ambiance

urban ambiance UQL1273 installation instructions

TotalPond

TotalPond 52238 instruction manual

Donner & Blitzen

Donner & Blitzen 0-02661479-2 owner's manual