Planar Dome E4c User manual

Dome E4c Display

Quick Reference

Windows XP

Windows 2000

020-0437-03A_1.indd 1020-0437-03A_1.indd 1 11/28/06 10:59:59 AM11/28/06 10:59:59 AM

Display Features

•AMLCD color panel designed for

widescreen diagnostic imaging.

•High resolution and high contrast

ratio combined for viewing color and

grayscale images simultaneously.

•Bezel-free framing of 4 megapixels

of data presented in a landscape

resolution of 2560 x 1600 pixels.

•Gamma correction achieved on

true color display from a palette of

1786 near-gray values.

•Integrated RightLight technology

applied to monitor and stabilize

backlight luminance.

System Requirements

•Intel Pentium 4/Xeon;

AMD Athlon 64/K7/XP or compatible

•PCI Express x16 lane slot

•50 MB hard disk space

•256 MB RAM

•CD-ROM drive

•Power supply, 350 watts or greater

•Windows XP Service Pack 2 or

Windows 2000 Service Pack 4

Read all instructions before setting up the Dome E4c display. Improper use of

the display can result in electric shock, re, or damage to display components.

Go to www.planar.com/support for more product documentation.

Warning

Avertissement

Avvertenza

Advertencia

Warnung

Wear an antistatic heel or wrist strap

when installing the video card to avoid

damage to computer components.

020-0437-03A_1.indd 2020-0437-03A_1.indd 2 11/28/06 11:00:00 AM11/28/06 11:00:00 AM

Check the contents of your Dome E4c display package for all the items shown

here. Save the original packaging materials for storage and shipping.

IMPORTANT: Read “Handling the Display” on page 10 before you set up

the display.

Unpacking the Display

Software CDsPower cord

Graphics card Power adapter

Option available: VESA wall mounting kit.

020-0437-03A_1.indd 3020-0437-03A_1.indd 3 11/28/06 11:00:00 AM11/28/06 11:00:00 AM

Display Components

The LED on the display front

indicates display status. Green, the

display is connected and running

properly. Amber, the video signal is

not being received.

The integrated video cable and

input power port are located on

the back. NOTE: You can connect

the video cable to either port

of the graphics card. Both ports

support the display with the full,

non-scaled 2560 x 1600 resolution.

In operation, when the cable is

disconnected, the display backlight

turns o and the unit enters power-

saving mode.

No other user-accessible controls

are available. You must use the

Dome CXtra software to control

display brightness and power-

saving functions.

After installation, the display turns

on automatically when you turn

on your computer system.

LED

020-0437-03A_1.indd 4020-0437-03A_1.indd 4 11/28/06 11:00:01 AM11/28/06 11:00:01 AM

(bottom view without stand)

Integrated

DVI cable

Power

port

020-0437-03A_1.indd 5020-0437-03A_1.indd 5 11/28/06 11:00:02 AM11/28/06 11:00:02 AM

Installing the Display Controller

To install the controller

1 Turn o your computer and all

peripherals. Disconnect all cables

from your computer. Leave the

power cord plugged into the

grounded outlet.

2 Remove the computer cover.

3 Remove any existing graphics card

and video signal cable, if necessary.

4 Remove the blank bracket from the

available PCI Express slot.

5 Insert the controller into the slot,

align the connector pins, and

press the board down until it

is rmly seated.

6 Secure the mounting bracket.

7 Reattach the computer cover

and the peripherals.

Remove any existing graphics card and its driver from your computer system

before you install the AX5 controller and driver. Also disable any onboard

graphics capability on the motherboard. See safety precautions on page 2.

Open PCI Express slot

Blank bracket

AX5 controller installed

020-0437-03A_1.indd 6020-0437-03A_1.indd 6 11/28/06 11:00:02 AM11/28/06 11:00:02 AM

Connecting the Display

To connect the display

1 Connect the DVI cable to either port

of the installed controller board.

NOTE: The AX5 board provides

dual-head functionality: You can run

two Dome E4c displays from one AX5

board. Both DVI ports provide dual-

link functionality and support each

Dome E4c display with the full,

non-scaled 2560 x 1600 resolution.

2 Plug the power cord into the input

power port on the connector plate.

3 Plug the other end of the power

cord into a grounded outlet.

NOTE: The display turns on automatically

when you turn on your computer system.

Use only the power cord supplied with your display.

AX5 controller

installed

DVI cable

The bottom port of the

AX5 board has

primary assignment.

020-0437-03A_1.indd 7020-0437-03A_1.indd 7 11/28/06 11:00:03 AM11/28/06 11:00:03 AM

Before you install the driver, remove any previously installed display driver

for the display controller from your system.

To install the display driver

1 Start the system. Click Cancel on the Found New Hardware Wizard.

Click No when the system prompts you to restart the computer.

2 Insert the driver installation CD and run Setup.exe.

3 Click Next.

4 Click Yes to the license agreement. The installation starts.

5 Follow the onscreen instructions to complete the installation.

Planar recommends that you select the Express installation option.

6 When the Setup complete message appears, select Yes, I want to

restart my computer now and click Finish.

7 If the Digital Signature Not Found message appears, click Yes or

Continue to complete the driver installation.

Installing the Display Driver

020-0437-03A_1.indd 8020-0437-03A_1.indd 8 11/28/06 11:00:03 AM11/28/06 11:00:03 AM

Use the Display Properties dialog to make changes to the video settings.

To congure the display

1 Right-click the desktop and select Properties > Settings.

2 Use the native resolution of the display.

3 Click OK until you return to the desktop.

To set the brightness

You must have the Dome CXtra software installed to change the display

brightness. Adjust the value of the white level on the Backlight tab of

the RightLight Panel Conguration dialog.

Adjusting the Display Properties

020-0437-03A_1.indd 9020-0437-03A_1.indd 9 11/28/06 11:00:04 AM11/28/06 11:00:04 AM

Handling the Display

•Set up your display on a stable,

level surface away from any direct

light or heat source, but near a

grounded AC outlet.

•Choose a well-ventilated location

with an adequate amount of space.

Do not block the vents on the back

of the display.

•Never lift the display by the desk

stand. Use both hands to lift or

move the display. Avoid touching

the screen.

•Never apply pressure to the screen

or touch the screen with bare ngers

or with any objects.

•Allow the display unit to reach room

temperature before you power it on.

Ambient room temperature ranges

from 20°C to 25°C (68°F to 77°F).

•Avoid sudden temperature changes

in the environment, as this may cause

condensation in the display.

•Never remove the back cover or

disassemble the display. There are

no user-serviceable parts inside.

•When troubleshooting, check that all

cables are properly connected and

that your computer is turned on or

not in power-saving mode.

•Follow your local governing

ordinance for proper disposal or

recycling of electronic components.

Hand injury may result from misuse of the desk stand when

lowering the display height. Avoid holding the bottom area

of the display. Never place your hands between the display

and the desk stand.

To lower the display height, grasp both sides of the display

and push down.

020-0437-03A_1.indd 10020-0437-03A_1.indd 10 11/28/06 11:00:04 AM11/28/06 11:00:04 AM

Other manuals for Dome E4c

Table of contents

Popular Monitor manuals by other brands

Linear Acoustic

Linear Acoustic LQ-1000 user guide

AOC

AOC I2579V user manual

Gateway

Gateway FPD1520 user guide

Furuno

Furuno Mu 120c Operator's manual

Asus

Asus VB171D - 17" LCD Monitor Service manual

Dell

Dell S2230MX Setting up

Philips

Philips 107C64 user manual

Dell

Dell S2409WFP user guide

EverFocus

EverFocus EN-7517E instruction manual

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Service manual

Dell

Dell Precision 7680 Connection guide

LG 50PM1M - - 50" Plasma Panel Service manual

Bosch

Bosch DDU 9 manual

Acer

Acer A231HL user manual

Philips

Philips 86BDL4152T user manual

NEC

NEC AccuSync LCD5V user manual

Emay

Emay SleepO2 user manual

IBM

IBM 6360 Product support manual